Related Manuals for Aktakom AMM-1062
Summary of Contents for Aktakom AMM-1062
- Page 1 MULTI-TESTER AMM-1062 User’s Manual 6 IN 1 SOUND LEVEL LIGHT HUMIDITY TEMPERATUPRE MULTIMETER Non-contact AC Voltage Test http://www.tmatlantic.com...
-
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION………………………………………2 INFORMATION FOR SAFETY…………………………3 FEATURES………………………………………………4 SPECIFICATIONS………………………………………4 PANEL DESCRIPTION………………………………10 OPERATING INSTRUCTION…………………………12 MAINTENANCE………………………………………21... -
Page 4: Introduction
1. INTRODUCTION The 6 in 1 digital multi-tester has been designed to combine the functions of Sound Level Meter, Light Meter, Humidity Meter, Temperature Meter Non-contact AC Voltage Test Meter and Digital Multimeter. It is an ideal multi-function Instrument with scores of practical applications for professional and home use. -
Page 5: Information For Safety
2 SAFETY INSTRUCTIONS This meter has been designed for safe use, but must be operated with caution. The rules listed below must be carefully followed for safe operation. NEVER apply voltage or current to the meter that exceeds the specified maximum: Input Protection Limits Function Maximum Input... -
Page 6: Features
3 FEATURES 14 functions measure Sound level, Light, Humidity, Temperature, DC Voltage, AC Voltage, DC Current, AC Current,Resistance, Diode and Continuity test. 3 4/5Digital large LCD display with units of Lux, °C, % and dB indication. Easy to use with single function switch operating, pocket size and light weight. - Page 7 Dimensions: 170 (H)x78(W) x48(D) mm Weight: Approx: 335g including holster. Accuracy is given at 18 °C to 28 °C (65 °F to 83 °F), less than 70 % RH Sound Level Measurement range: 35-100dB Resolution: 0.1dB Typical instrument frequency range: 30Hz-10kHz Frequency Weighting: C –weighting Time Weighting: Fast Accuracy: ±...
- Page 8 Humidity/Temperature K type temperatur Measurement Range: Range Resolution Accuracy -4°F~+2372°F 1°F 3% of rdg ± 9 dgts -20°C~+1300°C 1°C 3% of rdg ± 5 dgts Input Impedance: 10M: Overload Protection: 250Vdc or ac rms. for 400mV range and 250V dc or 250V ac rms. for other ranges. Indoor Temperature Range: Range Resolution...
- Page 9 Input Impedance: 10M: Overload Protection: 600Vdc or ac rms. for 400mV range and 600V dc or 600V ac rms. for other ranges. AC Voltage (Auto-ranging except 400mV) Range Resolution Accuracy 400.0mV 0.1mV ± 1.5%of rdg ± 15dgts 4.000V 1.0mV ± 1.0% of rdg ± 4 dgts 40.00V 10mV 400.0V...
- Page 10 AC Current (Auto-ranging for uA and mA) Range Resolution Accuracy 400.0uA 0.1uA ± 1.2% of rdg ± 2 dgts 4000uA ± 1.2% of rdg ± 2 dgts 400.0mA 100uA ± 1.5% of rdg ± 2 dgts 10.00A 10mA ± 2.0% of rdg ± 5 dgts Overload Protection: 500mA /660V and 10A / 600V Fuse AC Response: 50 Hz to 400 Hz Maximum Input: 400mA dc or 400mA ac rms on uA / mA...
- Page 11 Capacitance (Auto-ranging) Range Resolution Accuracy 50.00nF 10pF ± 5.0% of rdg ± 7 dgts 500.0nF 0.1nF ± 3.0% of rdg ± 5 dgts 5.000μF ± 4.0% of rdg ± 5 dgts 50.00μF 10nF 100.0μF 0.1uF Input Protection: 600V dc or 600V ac rms Frequency (Auto-ranging) Range Resolution...
-
Page 12: Panel Description
Diode and Continuity check Diode: Test current 1.4mA dc and open circuit voltage 2.8V Continuity: Built in Buzzer will be sound if the circuit resistance is less than 50: Overload Protection: maximum 600V dc or 600V ac rms. PANEL DESCRIPTION Humidity &... - Page 13 11. Hold button The HOLD function allows the meter to "freeze" a measurement for later reference.Press the HOLD button to “freeze” the reading on the indicator. The “HOLD” message will be appear in the display. 12. Backlight button Press the backlight button for LCD light , again Press the backligh button to exit light mode.
-
Page 14: Operating Instruction
6. OPERATING INSTRUCTION Measuring Sound Level 1. Set the function switch to the green “dB” position. 2. Remove the meter and face the microphone to sound source in a horizontal position. 3. The C-weighting curve is nearly uniform over the frequency range from 30 to 10,000Hz, thus giving an indication of overall Sound level. - Page 15 When the measurement is completed. Replace the photo detector from the light source. Spectral sensitivity characteristic: To the detector, the applied photo diode with filters makes the spectral sensitivity characteristic almost meet C.I.E. (International Commission on Illumination) photopia curve V (O) as the following chart described. 100% (Relative Sensitivity) Spectral Sensitivity...
- Page 16 7. Recommended Illumination: Locations *Office Conference, Reception room. 200 ~ 750 Clerical work 700 ~ 1,500 Typing drafting 1000 ~ 2,000 *Factory Packing work, Entrance passage 150 ~ 300 Visual work at production line 300 ~ 750 Inspection work 750 ~ 1,500 Electronic parts assembly line 1500 ~ 3,000 *Hotel...
- Page 17 Measuring Temperature 1. Temperature Measurement for Outdoor: 2 Set the function switch to the green “0.1 °C” position or “1 °C” position . 3 Then the display will show the environment temperature reading value °C directly. 4 Insert the black plug of temperature probe the COM jack and red plug to the "...
- Page 18 Measuring AC Voltage 1. Insert the black test lead banana to the COM jack and red test lead banana to the “V/Hz%/ /Cap/ °C” jack. 2. Set the function switch to the green at AC ranges to be used and connect test leads connect test leads across the source or load under measurement.
- Page 19 6. Remove power from the circuit under test, then open up the circuit at the point where you wish to measure current. 7. Touch the black test probe tip to the negative side of the circuit. Touch the red test probe tip to the positive side of the circuit.
- Page 20 Touch the black test probe tip to the neutral side of the circuit. Touch the red test probe tip to the “hot” side of the circuit. Apply power to the circuit. Read the current in the display. 10. Press and hold the Hz% button to indicate “Hz”. 11.
- Page 21 Measuring Frequence Set the function switch to the Hz position. Insert the black test lead banana plug into the negative (COM) jack Insert the red test lead banana plug into the V/Hz%/ /Cap/°C jack. Touch the test probe tips to the circuit under test. Read the frequency in the display.
- Page 22 Measuring Diode 1. Set the function switch to the green position. 2. Insert the black test lead banana plug into the negative COM jack and the red test lead banana plug into the V/Hz%/ /Cap/°C jack. 3. Press the MODE button to indicate “ “...
-
Page 23: Maintenance
Non-contact AC Voltage Test (NCV) 1. Set the function switch to the ON position. 2. Remove the meter and face the NCV detector to ACV source. 3. If source votalge in 50-1000V the NCV indicate lamp will light. 7. MAINTENANCE Battery and Fuse Replacement If the sign “... - Page 24 v081020...