Related Manuals for SHOWTEC TECHNO DERBY V1
Summary of Contents for SHOWTEC TECHNO DERBY V1
- Page 1 MANUAL ENGLISH Techno Derby Ordercode: 43156 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Techno Derby Table of contents Warning ....................................2 Unpacking Instructions ..............................2 LED Expected Lifespan ..............................2 Safety Instructions ................................. 2 Operating Determinations ............................4 Rigging .................................... 4 Connection with the mains............................5 Return Procedure ................................6 Claims ....................................6 Description of the device .............................. -
Page 3: Warning
Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: • Showtec Techno Derby • IEC power cable (1,75 m) •... - Page 4 Leave the device switched off until it has reached room temperature. • If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
-
Page 5: Operating Determinations
Techno Derby Operating Determinations • This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. • The minimum distance between light output and the illuminated surface must be bigger than 1 meter. -
Page 6: Connection With The Mains
Techno Derby Mounting a clamp to the Techno Derby Improper installation can cause serious injuries to people and/or damage of property ! Connection with the mains Connect the device to the mains with the power plug. Always check if the right color cable is connected to the right place. International EU Cable UK Cable... -
Page 7: Return Procedure
Techno Derby Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture. -
Page 8: Description Of The Device
Techno Derby Description of the device Features The Showtec Techno Derby is a light fixture with high output and great effects. • Power: 100~240VAC 60/50Hz • Power consumption: 30W • 4-digit LED display • 1 and 4 DMX channels •... -
Page 9: Backside
Techno Derby Backside Fig. 02 08) IEC power connector OUT 09) IEC power connector IN + Fuse T1A/250V 10) 3-pin DMX signal connector OUT 11) 3-pin DMX signal connector IN 12) LED display + control buttons 13) Sound sensitivity control 14) Safety eye 15) Built-in microphone 16) Ground/earth connection... -
Page 10: Control Modes
Techno Derby Control Modes There are 4 modes: Built-in programs (stand-alone) Sound-controlled Master/Slave DMX-512 (1CH, 4CH) One Techno Derby (Stand-alone) 01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Plug the end of the electric mains power cord into a proper electric power supply socket. -
Page 11: Multiple Techno Derbys (Dmx Control)
Techno Derby Multiple Techno Derbys (DMX Control) 01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Plug the end of the electric mains power cord into a proper electric power supply socket. 04) Use a 3-p XLR cable to connect the Techno Derbys and other devices. -
Page 12: Fixture Linking
Techno Derby Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. -
Page 13: Control Panel
Techno Derby Control Panel A) LED display MENU button C) UP button D) DOWN button ENTER button Fig. 05 Control Mode The fixtures are individually addressed on a data-link and connected to the controller. The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it, the controller will display the saved DMX address the next time.) DMX Addressing The control panel on the front side of the base allows you to assign the DMX fixture address, which is the... -
Page 14: Menu Overview
Techno Derby Menu Overview Ordercode: 43156... -
Page 15: Main Menu Options
Techno Derby Main Menu Options Built-in Shows Sound-controlled Color Settings Strobe Shows DMX-512 Mode Master/Slave Mode System Settings 1. Built-in Shows 01) Press the MENU button until the display shows 02) Press the ENTER button to enter the menu. 03) Press the UP and DOWN buttons to choose between the 3 built-in shows: 04) Press the ENTER button to choose your preferred built-in show. -
Page 16: Color Settings
Techno Derby 3. Color Settings 01) Press the UP and DOWN buttons until the display shows 02) Press the ENTER button to proceed. The display will show 03) Press the ENTER button to enter the edition mode. 04) Repeatedly press the ENTER button to toggle between the following color settings: Red color intensity 000 = OFF, 255 = Full ON Green color intensity... -
Page 17: System Settings
Techno Derby 7. System Settings 01) Press the UP and DOWN buttons until the display shows 02) Press the ENTER button to enter the menu. 03) Repeatedly press the UP and DOWN buttons to toggle between the following system settings: LED power saving mode Setting Reset Test Mode... -
Page 18: Remote Control
Techno Derby Remote Control Button Function Description On / Off Switch the device ON or OFF Auto Mode Activate/deactivate Built-in Auto Shows mode Sound-controlled Mode Activate/deactivate Sound-controlled mode LED Mode Activate/deactivate LED mode Activate strobe shows (press repeatedly to toggle between Strobe Show different strobe shows) Strobe... -
Page 19: Channels
Techno Derby 4 channels Channel 1 – LED Color Settings Not functional 6-20 21-35 Green 36-50 Blue 51-65 White 66-80 Red + Green 81-95 Red + Blue 96-110 Red + White 111-125 Green + Blue 126-140 Green + White 141-155 Blue + White 156-170 Red + Green + Blue... -
Page 20: Maintenance
Techno Derby Maintenance The Showtec Techno Derby requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply and then wipe the cover with a damp cloth. Wipe the front glass panel clean with glass cleaner and a soft cloth. - Page 21 Techno Derby Problem Probable cause(s) Solution • Check if power is switched on and One or more No power to the fixture fixtures do not cables are plugged in function at all Primary fuse blown • Replace fuse Fixtures reset The controller is not connected.
-
Page 22: Product Specifications
Techno Derby Product Specifications Model Showtec Techno Derby Input Voltage: 100~240VAC 50/60Hz Power consumption: Fuse: T1A/250V Dimensions: 265 mm x 190 mm x 190 mm (LxWxH) Weight: 1,5 kg Operation and Programming Signal pin OUT: pin 1 earth, pin 2 (-), pin 3 (+) -
Page 23: Dimensions
Techno Derby Dimensions Ordercode: 43156... -
Page 24: Notes
Techno Derby Notes Ordercode: 43156... - Page 25 Techno Derby Ordercode: 43156...
- Page 26 ©2015 Showtec...