Spectral 260 White Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear to be damaged from shipping or the carton itself shows signs of mishandling.
Page 4
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
Spectral 260 White Operating Determinations ● This device is not designed for permanent operation. Regular operation breaks will ensure that the device will serve you for a long time without defects. ● The minimum distance between light-output and the illuminated surface must be bigger than 0,5 meter.
Spectral 260 White Connection with the mains Connect the device to the mains with the power plug. Always check if the right color cable is connected to the right place. International EU Cable UK Cable US Cable BROWN YELLOW/COPPER PHASE...
Spectral 260 White Description of the device Features The Spectral 260 White is a compact indoor LED fixture from Showtec with 4x warm white and 3x cool white LEDs. ● Input Voltage: 100-240V AC Multi voltage ● Power consumption: 8 Watt at full output ●...
07) Special DMX-IN/ DMX-OUT cable Installation Remove all packing materials from the Spectral 260 White. Check that all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly.
Spectral 260 White No function #1, #3, #4 and #12 Program 4 (strobe) #1, #3 and #12 Program 5 (static) #1, #4 and #12 Program 6 (cool white) #1 and #12 No function #2, #3, #4 and #12 Program 7 (random strobe)
Spectral 260 White Multiple Spectrals (Master/Slave control) 01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Use the safety cable which is included. 03) Use a 3-p XLR cable to connect the Spectral and other devices.
Spectral 260 White Multiple Spectrals (DMX512 Mode) 01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Use the safety cable which is included. 03) Plug the end of the electric mains power cord into a proper electric power supply socket.
Spectral 260 White Dipswitch setting for DMX mode DMX products must have their own "address" to receive DMX signals. Addresses on the controller are set by flipping the appropriate DMX Dip switches #1-#9. Starting address: DMX channel 1 You need to know that DMX address settings are the sum of the dip switch values.
Spectral 260 White Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support.
Spectral 260 White DMX Modes The Spectral has 4 different DMX modes, see below. DIP Switches ON Function 2 CHANNELS (STD.W) 2 CHANNELS (STD.1) 3 CHANNELS (STD.D) 5 CHANNELS (S1.DS) Ordercode: 43518...
04) The electric power supply cables must not show any damages or material fatigue. The Showtec Spectral 260 White requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply and then wipe the cover with a damp cloth.
Page 18
Spectral 260 White Problem Probable cause(s) Remedy One or more No power to the fixture. ● Check if power is switched on and fixtures do not cables are plugged in function at all Fixtures reset The controller is not connected.
Spectral 260 White Product Specifications Model: Showtec Spectral 260 White Input Voltage: 100-240V AC Multi voltage Power consumption: 8 Watt Drive current: 350mA Dimensions: 175 x 110 x 155mm (LxWxH) Weight: 0,74 kg Operating and Programming: Signal pin OUT: Pin 1 (earth), pin 2 (-), pin 3 (+)