LED Blinder 2 COB Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling.
Page 4
For adult use only. The device must be installed out of the reach of children. Never leave the unit running unattended. • The user is responsible for correct positioning and operating of the LED Blinder 2 COB. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device.
LED Blinder 2 COB Operating Determinations • This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. • The minimum distance between light output and the illuminated surface must be bigger than 1 meter.
LED Blinder 2 COB The Stage Blinder can be placed on a flat stage floor or mounted to any kind of truss with a clamp. Improper installation can cause serious injuries and/or damage of property! Connection with the mains Connect the device to the mains with the power-plug.
LED Blinder 2 COB Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Description of the device Features The Showtec LED Blinder is our first LED light effect which matches the blinding light output of a conventional Audience Blinder. A sturdy housing, Powercon in-and output, 3-and 5-pin dmx connections and COB LED technology makes this a perfect show product which can be used in any situation.
LED Blinder 2 COB Backside Fig. 02 04) Ground/earth connection 05) Grey Pro Power connector 06) 5-pin DMX signal connector OUT 07) 3-pin DMX signal connector OUT 08) Safety Eye 09) LCD Display + 3 Menu buttons 10) 5-pin DMX signal connector IN...
LED Blinder 2 COB Control Modes There are 4 modes: • Built-in programs • Manual Mode • Master/Slave • DMX-512 (1CH, 2CH, 3CH and 4CH) One LED Blinder (Built-in programs and Manual Mode) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
LED Blinder 2 COB Multiple LED Blinders (DMX Control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Use a 3-pin XLR cable to connect the LED Blinders and other devices.
LED Blinder 2 COB Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support.
LED Blinder 2 COB The LED Blinder can be operated with a controller in control mode or without the controller in stand-alone mode. Control Panel A) LCD display MODE button C) UP button D) DOWN button Fig. 05 Control Mode The fixtures are individually addressed on a data-link and connected to the controller.
LED Blinder 2 COB Main Menu Options DMX 1-channel mode DMX 2-channel mode DMX 3-channel mode DMX 4-channel mode Built-in programs Program speed Warm White LED brightness (Manual Mode) Display lock Dimmer Curve 1. DMX 1-channel mode With this menu, you can set the DMX address in 1-channel mode.
LED Blinder 2 COB 6. Program speed With this menu, you can set the built-in program speed. 01) Press the MODE button until the display shows 02) Press the UP/DOWN buttons to increase/decrease the program speed. The adjustment range is between 1-16, from slow to fast.
Suspect three potential problem areas as: the power supply, the LEDs, the fuse. 01) Power supply. Check that the unit is plugged into an appropriate power supply. 02) The LEDs. Return the LED Blinder to your Showtec dealer. 03) The fuse. Replace the fuse. See page 17 for replacing the fuse.
Page 19
Turn up the air conditioning • Disconnect the fixture and Lamp is damaged replace the lamp • Return the device to your Showtec dealer The power supply settings do not • Disconnect fixture. Check settings match local AC voltage and...
LED Blinder 2 COB Product Specifications Model: Showtec LED Blinder 2 COB Input Voltage: 100-240VAC, 50/60Hz Power consumption: 110W (full output) DMX linking: 30pcs Dimensions: 393 x 138 x 185 mm (without bracket) (LxWxH) Weight: 4,14 kg Operating and Programming:...