Related Manuals for Pepperl+Fuchs OBD10M-R2000-4EP
Summary of Contents for Pepperl+Fuchs OBD10M-R2000-4EP
- Page 1 FACTORY AUTOMATION MANUAL 2-D Laser Scanner OBD10M-R2000-4EP OBD30M-R2000-4EP OBD30M-R2000-4EP-T OBD10M-R2000-4EP OBD30M-R2000-4EP OBD30M-R2000-4EP-T...
- Page 2 2-D Laser Scanner With regard to the supply of products, the current issue of the following document is applicable: The General Terms of Delivery for Products and Services of the Elec- trical Industry, published by the Central Association of the Electrical Industry (Zen- tralverband Elektrotechnik und Elektroindustrie (ZVEI) e.V.) in its most recent version as well as the supplementary clause: "Expanded reservation of proprietor- ship"...
-
Page 3: Table Of Contents
2-D Laser Scanner Contents 1 Introduction................. 2 Purpose of this quick start guide ..............2 Product documentation on the internet............2 Intended Use ....................2 Validity ......................2 2 Safety ................... 3 Laser Class 1 ....................3 3 Product Description ............4 Indicators and Operating Controls ..............4 Interfaces and Connections ................4 Included in Delivery..................5 Accessories ....................6... -
Page 4: Introduction
2-D Laser Scanner Introduction Introduction Purpose of this quick start guide This quick start guide contains basic instructions for operating the device. However, the manual takes priority over the quick start guide. Product documentation on the internet You can view all the relevant documentation and additional information on your product at http://www.pepperl-fuchs.com. -
Page 5: Safety
2-D Laser Scanner Safety Safety Laser Class 1 Class 1 Laser Product This sensor is certified according to laser protection class 1. Warning! Class 1 laser light The laser light can be an irritant, especially in a dark environment. Do not point lasers at people! Maintenance and repairs should only be carried out by authorized service personnel! -
Page 6: Product Description
2-D Laser Scanner Product Description Product Description Indicators and Operating Controls Figure 3.1 Indicators and Controls Designation Color Operating status indicator Green Error indicator "Next" menu button "Return" menu button Q2—input/output 2 Yellow Q1—input/output 1 Yellow Laser face Ethernet link indicator Green Ethernet activity indicator Yellow... -
Page 7: Included In Delivery
2-D Laser Scanner Product Description MultiPort An 8-pin M12 connector is located on the rear of the housing. Inputs/outputs 3 and 4 are located here DNC (Do not connect) DNC (Do not connect) DNC (Do not connect) I/Q3 I/Q4 DNC (Do not connect) DNC (Do not connect) DNC (Do not connect) All pins with "DNC (Do not connect)"... -
Page 8: Accessories
2-D Laser Scanner Product Description Accessories The following products are available as accessories. Designation Description V1SD-G-2M-PUR-ABG-V45-G Patch cable M12 to RJ45, length 2 m V1SD-G-5M-PUR-ABG-V45-G Patch cable M12 to RJ45, length 5 m V1SD-G-ABG-PG9 Single-ended male cordset, M12 D-coded, 4-pin for bus cable V1-G-2M-PUR Single-ended female cordset, straight, M12, 4-pin, PUR cable, length 2 m... -
Page 9: Installation
2-D Laser Scanner Installation Installation Mounting Caution! Safety information Do not point the sensor into the sun. Protect the sensor against direct and prolonged sunlight. Prevent condensation from forming by ensuring that the sensor is not subjected to any major temperature fluctuations. Do not subject the sensor to aggressive chemicals. -
Page 10: Device Connection
2-D Laser Scanner Installation Note! Keep the emitting/receiving area clear During assembly, make sure that the emitting/receiving area is kept clear. If the emitting/receiving area is covered, this reduces the performance of the 2D laser scanner. Device Connection Electrical connection in line with IP65 Put protective covers on unused M12 connectors. -
Page 11: Commissioning
2. There is another initialization phase that lasts approx. 10 seconds. The display turns on and shows circles moving downward. 3. After the initialization phase, the Pepperl+Fuchs logo will appear. The device is ready for operation. To achieve the best measurement accuracy, allow the device to warm up for 30 minutes. - Page 12 2-D Laser Scanner Commissioning DHCP Set the device to DHCP under the "Address mode" menu item. The DHCP configuration requires a DHCP server in the local network, e.g., a router. See the "Auto IP" item for information on this. Manual IP Set the device to manual under the "Address mode"...
- Page 13 Twinsburg, Ohio 44087 · USA Tel. +1 330 4253555 E-mail: sales@us.pepperl-fuchs.com Asia Pacific Headquarters Pepperl+Fuchs Pte Ltd. Company Registration No. 199003130E Singapore 139942 Tel. +65 67799091 E-mail: sales@sg.pepperl-fuchs.com www.pepperl-fuchs.com Subject to modifications Copyright PEPPERL+FUCHS • Printed in Germany DOCT-3777C 03/2016...