Table of Contents
Advertisement
GENERAL INFORMATION
1.7 UNPACKING
AND INSPECTION
1.7.1 Inspection
for Damage
Upon receiving the Model 7072, carefully unpack it from
its shipping
carton and inspect the card for any obvious
signs of physical damage. Report any such damage to the
shipping agent immediately.
Save the original packing car-
ton for possible future reshipment.
1.7.2 Shipment
Contents
The following
items are included
with every Model 7072
order:
l
Model 7072 Semiconductor
Matrix
Card.
l
Model 7072 Instruction
Manual.
l
Coaxial jumper cables (4) for matrix expansion.
l
Additional
Accessories as ordered.
1.7.3 Instruction
Manual
-
The Model 7072 Instruction
Manual is three-hole
drilled
so that it can be added to the three-ring
binder
of the
Model 707 Switching
Matrix
Instruction
Manual.
After
removing
the plastic wrapping,
place the manual in the
binder after the mainframe instruction
manual. Note that
a manual identification
tab is included and should precede
the matrix card instruction
manual.
If an additional
instruction
manual is required,
order the
manual package, Keithley
part number 7072-901-00. The
manual package includes an instruction
manual and any
pertinent
addenda.
1.8 REPACKING
FOR SHIPMENT
Should it become necesary to return the Model 7072 for
repair, carefully pack the card in its original packing car-
ton
or the
equivalent,
and
include
the
following
information:
l
Advise as to the warranty
status of the matrix card.
l
Write ATTENTION
REPAIR DEPARTMENT
on the ship-
ping label.
l
Fill out and include the service form located at the back
of this manual.
1.9 OPTIONAL
ACCESSORIES
The following
accessories are available to make connec-
tions to the Model 7072.
Model 61713~slot Male to 2-lug Female Triaxial Adapters-
The Model 6l7I allows male 2.lug triaxial cables to be con-
nected to the Model 7072.
Model 7078-TRX-T 3-Lug Trim Tee Adapter-The
Model
7078-TRX-T allows multiple
trim connections
to the Model
7072 column or row jacks.
Model 707%TRX-BNC 3-Lug Triax to BNC Adapter-The
Model 7078~TRX-BNC allows BNC cables to be connected
to the Model 7072.
Model
7078-m
Triaxial
Cables-The
Model
7078-TRX
cables are terminated
with 3-slot male triaxial connectors.
The Model 7078-TRX-3 is 0.9m (3 ft.) in length,
and the
Model 7078-TRx-10 is 3m (10 ft.) long.
Model 7078-TBC 3-Lug Female Trim Bulkhead Connector
with Cap-The
Model 7U78-TBC can be used for applica-
tions such as test fixtures.
Model 7U78-CSHP Cable Set--The Model 707%CSHP Cable
Set includes the necessary cables and adapters to connect
the Model
7072 to the Hewlett-Packard
Model
4145
Semiconductor
Parameter
Analyzer.
The
Model
707%CSHP includes
four Model 7078.TRX-10 loft. 3-lug
triaxial cables, four Model 7051-10 loft. BNC cables, and
four Model 7078-TRX-BNC 3-lug triax to BNC adapters.
1.10 COAXIAL
JUMPER
ACCESS
Coaxial jumpers can be installed to expand rows A, B, G
and H of the matrix using two or more Model 7072 Cards.
An access door on the mainframe
allows access to these
jumpers. To allow access when the Model 7W is mounted
in a rack, it is recommended that the Model 7079 Slide Rack
Mount
Kit be used.
l-2
I
Advertisement
Table of Contents
