ADJ COB Cannon Wash DW User Instructions page 7

COB Cannon Wash DW
Static Color Mode:
1. Plug the fixture in and press the MODE button until "CLXX" is dis-
played.
2. There are 8 colors to choose from. Select your desired color by
pressing the UP and DOWN buttons. After you have selected your
desired color you can activate strobing by pressing the SET UP
button to enter the Flash (strobe) mode.
3. "FS.XX" will be displayed, this is Flash mode. The Flash can be
adjusted between "FS.00" (flash off) to "FS.15" (fastest flash).
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. The
COB Cannon Wash DW has 6 DMX modes: 1 channel mode, 2 chan-
nel mode, 3 channel mode, 4 channel mode, 5 channel mode, and a 6
channel mode. See page's 7-9 for each mode's DMX traits.
1. This function will allow you to control each individual fixture's
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
"d.XXX" is displayed. "XXX" represents the current displayed DMX
address. Use the UP or DOWN buttons to select your desired
DMX address, then press the SETUP button to select your DMX
Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 1 Channel Mode, press the MODE button until "Ch01"
is displayed. This is the 1 Channel DMX Mode.
• To run the 2 Channel Mode, press the MODE button until "Ch02"
is displayed. This is the 2 Channel DMX Mode.
• To run the 3 Channel Mode, press the MODE button until "Ch03"
is displayed. This is the 3 Channel DMX Mode.
• To run the 4 Channel Mode, press the MODE button until "Ch04"
is displayed. This is the 4 Channel DMX Mode.
• To run the 5 Channel Mode, press the MODE button until "Ch05"
is displayed. This is the 5 Channel DMX Mode.
• To run the 6 Channel Mode, press the MODE button until "Ch06"
is displayed. This is the 6 Channel DMX Mode.
4. Please see pages 7-9 for DMX values and traits.
ADJ Products, LLC - www.adj.com - COB Cannon Wash DW User Manual Page 12
Operating Instructions
COB Cannon Wash DW
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-
ler.
Default Running Mode:
This is a default running mode. When this mode is activated all modes
will return to their default settings.
1. Plug the fixture in and press the MODE button until "dXX" is dis-
played. "XX" represents either "on" or "oFF".
2. Press the SET UP button until "dEFA" is displayed.
3. Press the UP and DOWN buttons simultaneously. Press the
MODE button to exit.
DMX State:
This mode can be used as a precaution mode, that in case the DMX
signal is lost, the operating mode chosen in the setup is the running
mode the fixture will go into when the DMX signal is lost. You can also
set this as the operating mode you would like the unit to return to when
power is applied.
1. Plug the fixture in and press the MODE button until "d.XXX" is dis-
played. "XXX" represents the current displayed DMX address.
2. Press the SET UP button so that "nodn" is displayed. Use the UP
and DOWN buttons to scroll through the DMX states.
• "bLAC" (Blackout) - If the DMX signal is lost or interrupted,
the unit will automatically go into stand by mode.
• "LASt" (Last State) - If the DMX signal is lost or interrupted,
the fixture will stay in the last DMX set up. If power is applied and
this mode is set, the unit will automatically go into the last DMX set
up.
• "ProG" (Auto Run) - If the DMX signal is lost or interrupted,
the unit will automatically go into Auto Run mode.
3. Use the UP and DOWN buttons to find your desired DMX state
and press SET UP to confirm and exit.
Dimmer Curve:
This is used to set the dimming curve used with DMX mode. See
page 18 for the dimming curves chart.
1. Plug the fixture in and press the MODE button until "d.XXX" is dis-
played. "XXX" represents the current displayed DMX address.
ADJ Products, LLC - www.adj.com - COB Cannon Wash DW User Manual Page 13
Operating Instructions