Ltech WiFi-102 LED Controller User Manual page 2

.
3 SSID Number setting
Use code switch to set the controller's SSID Number-- WIFI-101-SSID-X, X is the code switch numerical value (total
16 No. from 0 to F). which means our product could set 16 isolated LAN in the same area. The controller will re-enter
initialization status once the code switch changes. RUN LED indicator light will flash quickly about 25 seconds, mobile
device need to search and connect WiFi again after Initialization finished.
EN
SC
FF
/O
R U N O N
ID
SS
Y
N K T KE
LI EX
TX
R X/
4. "ON/OFF" " Scene Key"
Press "ON/OFF "to turn on / off controller
Long press "Scene" to the 1st scene mode. short press
from 1 to 9, then changed back from 9 to 1.
AT &T AT &T 12:34 PM 12:34 PM AT &T AT &T
W W
110 60
Scene1
Scene2 Scene3
Scene4 Scene5 Scene6
Scene7 Scene8 Scene9
OK
Scene Settings
DIM driver scene
5 EXT Key network port .
EXT Key network port is used to connect the external button, 7 signal wires plus 1 GND wire,1# signal wire is the
ON/OFF button,2-7# signal wire represents 1-6 scene mode.
4. LED controller software instructions
(1) Ltech WIFI-100 software installation
this software has two versions -Android & iOS, choose the installation based on your mobile device. Check the
installation and usage of each version below
1) Installation of Android version: Transmit the installation package
Click to install.
)
2 installation of iOS version: A. search "WiFi-100 "
mobile device and install.
B. after connecting the mobile device with PC, search "WiFi-100"
through iTunes and install.
E
" "
Scene to scene mode sequentially , Scene mode changes
12:34 PM 12:34 PM AT &T AT &T 12:34 PM 12:34 PM
WW R G B
50 100 50 255 255 255 50
Scene1 Scene2 Scene3 Scene1 Scene2 Scene3
Scene4 Scene5 Scene6 Scene4 Scene5 Scene6
Scene7 Scene8 Scene9 Scene7 Scene8 Scene9
OK OK
Scene Settings Editor Scene Style Settings
RGB driver scene
CT driver scene
to the mobile device memory card and
in the App store
in the
3
(2) Software Operating Instructions
1. WiFi connection and settings
( ) 1 Click mobile devices' WiFi-setting, enable the WiFi function. The system will search automatically and list the
SSID No. for the controller (as shown below). Click the SSID No, to connect.
( ) 2 Click
to Enable software (if the Mobile devices'WiFi function is closed, the prompt box saying without WiFi
connection will pop up. Click "ok" to close the Dialog box and exit the application .go back to step (1) for the WiFi
connection.
Click settings to setting interface. Setting interface is used to switch among RGB, CT, DIM drivers and enter the
WiFi connection interface.
WiFi connection interface is for displaying the information of the connected controller.
Note: Device IP and port number are the fixed value, which are unchangeable.
Android WiFi connection
.
2 RGB,CT,DIM driver color wheel interface
Click" Setting "to setting interface, Select RGB, CT or DIM driver to get into each one's color wheel interface.
By touching the color wheel, the color, brightness, color temperature of the connected LED could be adjusted，
the brightness can also be changed by the brightness slider which is above the color wheel.
Click on the top right corner to turn on /off the controller. Click
save the scene
Scene save key
parameter values
brightness slider
color wheel
through
currently
selected color
Scene interface
key
return to a previous interface
AT &T 12:34 PM 12:34 PM AT &T 12:34 PM 12:34 PM
AT &T AT &T
Settings Settings
Driver
Driver
RGB Driver
CT Driver
DIM Driver
Wifi Connection
iOS WiFi connection setting interface
on the top left corner to Scene interface to
Save
AT &T AT &T 12:34 PM 12:34 PM AT &T AT &T 12:34 PM 12:34 PM AT &T AT &T
W 050 W 50 WW 100 R
Save Save Save
50
50 50
Current Current White White Current Current White White Current Current
Settings Settings
Scene Scene Editor
Dimming mode CT mode
4
12:34 PM
AT &T AT &T 12:34 PM
R G B
Save 255 255 255
50
Warning
Warning
Wifi is not enable currently! Wifi is not enable currently!
Do you want to turn it on now ?
OK
OK
Current White
Current White
Editor Scene Style Settings
prompt box saying without
WiFi connection
12:34 PM 12:34 PM
turn on/off the
255 G 255 B 255
controller
RGB editing interface
Click to restore the
default white
Modes
White White
Style Settings Setting
Scene
RGB mode