Sharp MD-X7H Service Manual page 55

2. AUTO adjustment mode
Step No. Setting Method
Step 1 Testmode STOP state
Step 2 Press the CD PLAY button two times. AUTO adjustment menu
Step 3 Press once the MD PLAY button. The slide moves to the innermost periphery, and automatic
End of adjustment
Step 4 Adjustment value output
Press the MD PLAY button.
Press the MD STOP button.
Step 5 Continuous playback (pit section)
Continuous playback (groove section)
Step 6 Press the CD STOP button.
Press the MD STOP button.
Step 7 Adjustment value output
Press the MD STOP button.
• : Adjustment name,
3. RESULT sub-mode
Step No. Setting Method
Step 1 Testmode STOP state
Step 2 Press the CD PLAY button three times. RESULT sub-menu
Step 3 Press once the MD PLAY button. Indication of measurement value
Step 4 Press once the CD PLAY button. Indication of measurement value
Step 5 Press once the CD PLAY button. Indication of measurement value
Step 6 Press once the CD PLAY button. Indication of measurement value
Step 7 Press once the CD PLAY button. Indication of measurement value
Step 8 Press once the CD PLAY button. Indication of measurement value
Step 9 Press once the CD PLAY button. Indication of measurement value
Step 10 Press once the CD PLAY button. Indication of measurement value
Step 11 Press once the CD PLAY button. Indication of measurement value
Step 12 Press once the CD PLAY button. Indication of measurement value
Step 13 Press once the CD PLAY button. Indication of measurement value
Step 14 Press once the CD PLAY button. Indication of measurement value
Step 15 Press once the CD PLAY button. Indication of measurement value
Step 16 Press once the CD PLAY button. Indication of measurement value
Step 17 Press once the CD PLAY button. Indication of measurement value
Step 18 Press once the CD PLAY button. Indication of measurement value
Step 19 Press once the CD PLAY button. Indication of measurement value
Step 20 Press once the CD PLAY button. Indication of measurement value
Step 21 Press once the CD PLAY button. Indication of measurement value
Step 22 Press once the CD PLAY button. Indication of adjustment error sequence No.
Step 23 Press once the CD PLAY button. Indication of adjustment status
Step 24 Press once the CD PLAY button. Indication of pre-adjustment not completed (00)/completed (4B)
Step 25 Press once the MD PLAY button. RESULT sub-menu state
• : Measurement value,
• ressing the REC button causes reversing.
• If the VOL UP button is pressed while the set value is indicated, the set value increases, and the new set value is stored in RAM.
• If the VOL DOWN button is pressed while the set value is indicated, the set value reduces, and the new set value is stored in RAM.
• If the VOL UP/VOL DOWN button is held down, the set value changes continuously with 100 ms cycle.
• The digit of increase/decrease by the VOL UP/VOL DOWN button can be shifted with the aid of CD STOP button.
adjustment is started.
• In case of high reflection disc
PEG→HAG
•In case of low reflection disc
PEG→LAG→GCG→GEG→LAG
If adjustment is OK, Step 4.
If adjustment is NG, Step 7.
STEP 5
STEP 2
Continuous playback (groove section)
STEP 2 AUTO adjustment menu
STEP 2 AUTO adjustment menu
: Measurement value,
: Adjustment value,
Remarks
changes as follows.
changes as follows.
: Address
Remarks
: Other various informations
– 19 –
MD-X8H
Display
[ t s m e ]
[ A U T O _ A J S T _ ]
[ : _ _ _ _ _ _ ]
[ _ C O M P L E T E _ ]
[ s c ]
[ a c ]
[ a a ]
[ C a n ' t _ A D J . ]
Display
[ t s m e ]
[ _ R S T _ Y O B I _ ]
[ R F G : _ _ _ ]
[ R C G : _ _ _ ]
[ R T G : _ _ _ _ _ ]
[ G T G : _ _ _ _ _ ]
[ P C H : _ _ _ _ ]
[ G C H : _ _ _ _ ]
[ S A G : _ _ _ ]
[ S B G : _ _ _ ]
[ S E G : _ _ _ ]
[ S F G : _ _ _ ]
[ H A O : _ _ _]
[ H B O : _ _ _]
[ H E O : _ _ _]
[ H F O : _ _ _]
[ L A O : _ _ _]
[ L B O : _ _ _]
[ L E O : _ _ _]
[ L F O : _ _ _]
[ T C O : _ _ _ _]
[ Y O B : _ _ _ _]
[ D I F : _ _ _ _]
[ A D J : _ _ _ _]
[ _ R S T _ Y O B I _ ]