Advertisement
•
Once the terminal is connected, press
<ENTER>
1, 1, 1, 1, 2, 2, 2, 7
<
>
•
Press the
or
the COM0(serial) and USB connections.
•
Once the correct connection is selected, press
<ENTER>, press
<ENTER>
The terminal should now display 'CONFIG
REQUIRED' .
•
Press
<Func>
9, 9, 0, 5
•
The terminal should now display 'Swipe merchant
card' . Swipe your respective green ANZ multiPOS
and EFTPOS Merchant Card (Terminal ID Card). If you
do not have this, press
in the Terminal ID, then press <ENTER>.
<ENTER>
•
Keep pressing
main screen.
<Func>
•
Press
2, 4, 6, 8
until it goes back to the main screen.
•
Press
<Func>
8, 7,
<ENTER>
•
The screen will display 'Initialising Please Wait'
Once complete, the terminal will return to the home
screen and is ready to process transactions.
Note: if the screen does not display "Initialising Please
^
Wait", please contact ANZ Merchant Services on 1800
039 025 for further assistance.
INIT REQUIRED
If the terminal is displaying 'Init Required' , press
<ENTER>
<ENTER>. If the terminal again displays
8, 7,
'Init Required' , follow the steps below:
•
Disconnect the cable from the back of the terminal
and wait 30 seconds.
•
Reconnect the cable at the back of the terminal and
wait for the terminal to revert to the 'Init Required'
screen.
<Func>
<ENTER> <ENTER>
• Press
8, 7,
the terminal.
The terminal will start initialising, taking approx. 1 - 2
minutes to complete. If 'Init Required' still appears,
please call ANZ Merchant Services on 1800 039 025 for
further assistance.
TERMINAL SECURITY
Please ensure that the terminal is placed in a secure
location enabling the cardholder to use the keypad
without being observed by security cameras, CCTV
devices or by any other person.
<Func>
<ENTER>.
<
>
buttons to cycle between
again under Protocol.
<ENTER>
<ENTER>.
<CLEAR>
and manually key
until you get back to the
<ENTER> <ENTER>
<ENTER>.
on
PC EFTPOS SUPPORT
PC EFTPOS provides the software that allows
communication between your point of sale software
and the terminal / modem. Their helpdesk is available:
Monday to Friday: 8:30am – 10:00pm (AEST)
Saturday:
Sunday:
PC-EFTPOS:
Telephone:
Note: PC EFTPOS support is available on public holidays
with the exception of Good Friday, Easter Sunday,
Anzac Day, Christmas Day and Boxing Day.
CONFIGURING COMMUNICATION MODE
If you require your terminal to change communication
modes between GPRS, Dial-up and IP, please follow the
and wait
steps below.
1. Press
2. At "Swipe Merchant Card" Press
.
^
3. Press
4. Press 1 to select Dial-up communication mode
Press 6 to select GPRS communication mode
Press 7 to select IP communication mode
5. Press
6. Press
<Func>
Logon Successful" should display on the terminal.
7. Press
Initialisation Approved" should display on the
terminal.
10:00am – 5:00pm (AEST)
10:00am – 3:00pm (AEST)
www.pceftpos.com
02 9998 9800
<Func>
9, 9, 0, 5 and then press
<ENTER>
to go to" COMMS MODE" Screen
<ENTER>
until the ANZ main screen appears
<Func>
2, 4, 6, 8 <ENTER><ENTER>. "TMS
<Func>
8, 7 <ENTER><ENTER>. "ANZ
<ENTER>
<ENTER>
Advertisement
