Danfoss VLT FC 100 Service Manual page 16

Introduction
1 1
FC 102, FC 202, and FC 103
High/Normal Load*
Typical Shaft output at 400 V [kW]
Typical Shaft output at 460 V [hp]
Typical Shaft Output at 480 V [kW]
Enclosure IP21
Enclosure IP54
Output current
Continuous (at 400 V) [A]
Intermittent (60 s overload) (at 400 V) [A]
Continuous (at 460/500 V) [A]
Intermittent (60 s overload) (at 460/500 V)
[kVA]
Continuous kVA (at 400 V) [kVA]
Continuous kVA (at 460 V) [kVA]
Max. input current
Continuous (at 400 V) [A]
Continuous (at 460/500 V) [A]
Max. cable size: line power, motor, brake
and load share [mm
Max. external electrical fuses [A]
Estimated power loss at 400 V [W]
Estimated power loss at 460 V [W]
Weight, enclosure IP21, IP54 kg (lbs)
Weight, enclosure IP20 kg (lbs)
4)
Efficiency
Output frequency
*Normal overload = 110% current for 60 s
Table 1.12 Line Power Supply 3x380–480 V AC
1) For type of fuse, see the Instruction Manual.
2) American Wire Gauge
3) Measured using 16.5 ft [5 m] shielded motor cables at rated load and rated frequency.
4) The typical power loss is at nominal load conditions and within ± 15% (depending on various voltage and cable
conditions).
5) Field wiring terminals on FC 102 N132, N160, and N315 models are not intended to receive conductors one size
larger.
Values are based on a typical motor efficiency (eff2/eff3 border line). Motors with lower efficiency add to the
power loss in the adjustable frequency drive and those with higher efficiency decrease it.
The losses are based on the default switching frequency. The losses increase significantly at higher switching
frequencies. LCP and typical control card power consumption values are included. Further options and customer
load may add up to 30 W to the losses. (Though typically, only 4 W extra for a fully loaded control card, or options
for slot A or slot B, each).
14
Service Manual
N110
NO
110
150
132
D1h
D1h
D3h
212
233
190
209
147
151
204
183
2 ] (AWG 2) ) 5)
1) 315
4) 2555
2257
Danfoss A/S © Rev. 2014-02-10 All rights reserved.
N132 N160
NO NO
132 160
200 250
160 200
D1h D1h
D1h D1h
D3h D3h
260 315
286 347
240 302
264 332
180 218
191 241
251 304
231 291
2x95
(2x3/0)
350 400
2949 3764
2719 3622
62 (135)
62 (135)
0.98
0–800 Hz
N200 N250 N315
NO NO
200 250
300 350
250 315
D2h D2h D2h
D2h D2h D2h
D4h D4h D4h
395 480
435 528
361 443
397 487
274 333
288 353
381 381 463 463
348 348 427 427
2x185
(2x350)
550 630
4109 5129 6663
3561 4558 5703
125 (275)
125 (275)
0–600 Hz
MG94A222
NO
315
450
355
588
647
535
588
407
426
567
516
800