Explanation Of General View; Specifications; Intended Use; Power Supply - Makita 9561CH Angle Grinder

ENGLISH (Original instructions)
1-1. Shaft lock
2-1. Slide switch
3-1. Speed adjusting dial
5-1. Wheel guard
5-2. Bearing box
5-3. Screw
6-1. Wheel guard
6-2. Bearing box
6-3. Screw
7-1. Wheel guard
7-2. Bearing box
7-3. Screw
7-4. Lever

SPECIFICATIONS

Depressed center wheel diameter
Max. wheel thickness
Rated speed (n) / No load speed (n
Depressed center wheel diameter
Max. wheel thickness
Rated speed (n) / No load speed (n
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003

Intended use

The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.

Power supply

The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted
according to EN60745:

Explanation of general view

8-1. Screw
9-1. Lock nut
9-2. Depressed center grinding
wheel/Multi-disc
9-3. Inner flange
10-1. Lock nut wrench
10-2. Shaft lock
11-1. Lock nut
11-2. Abrasive disc
11-3. Rubber pad
12-1. Marking A
13-1. Marking B
14-1. Marking C
Model
Spindle thread
)
0
Overall length
Net weight
Safety class
Model
Spindle thread
)
0
Overall length
Net weight
Safety class
noise level determined
9561CH
115 mm
6.4 mm
M14
289 mm
2.2 kg
9561CVH
115 mm
6.4 mm
M14
289 mm
2.2 kg
ENE048-1
Model 9561CVH,9562CH, 9562CVH, 9564CV
Sound pressure level (L
Sound power level (L
ENF002-2
Uncertainty (K) : 3 dB (A)
Model 9565C, 9565CV
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
ENG905-1
4
15-1. Pin
15-2. Vent
17-1. Wire cup brush/Wire bevel brush
18-1. Lock nut
18-2. Abrasive cut-off wheel/diamond
wheel
18-3. Inner flange
18-4. Wheel guard for abrasive cut-off
wheel/diamond wheel
19-1. Exhaust vent
19-2. Inhalation vent
9562CH 9563C
125 mm 100 mm
6.4 mm 6.4 mm
M14 M10
-1
12,000 min
2.2 kg 2.1 kg
/II
9562CVH 9564CV
125 mm 115 mm
6.4 mm 6.4 mm
M14 M14
-1
12,000 min
299 mm
2.3 kg 2.3 kg
/II
) : 83 dB (A)
pA
) : 94 dB (A)
WA
) : 82 dB (A)
pA
) : 93 dB (A)
WA
Wear ear protection
9564C 9565C
115 mm 125 mm
6.4 mm 6.4 mm
M14 M14
299 mm
2.3 kg 2.3 kg
9565CV
125 mm
6.4 mm
M14
2.4 kg