Download  Print this page

Advertisement

INSTRUCTION MANUAL
Angle Grinder
9561CH
9561CVH
9562CH
9562CVH
9563C
9564C
9564CV
9565C
9565CV
007357
DOUBLE INSULATION
IMPORTANT: Read Before Using.
1

Advertisement

   Related Manuals for Makita 9561CH

   Summary of Contents for Makita 9561CH

  • Page 1 INSTRUCTION MANUAL Angle Grinder 9561CH 9561CVH 9562CH 9562CVH 9563C 9564C 9564CV 9565C 9565CV 007357 DOUBLE INSULATION IMPORTANT: Read Before Using.
  • Page 2: Specifications

    ENGLISH (Original instructions) SPECIFICATIONS Model 9561CH 9562CH 9563C 9564C 9565C Depressed center wheel diameter 115 mm 125 mm 100 mm 115 mm 125 mm Spindle thread Rated speed (n) / No load speed (n 12,000 min Overall length 289 mm...
  • Page 3 ) : 7.5 m/s EC Declaration of Conformity h,AG Uncertainty (K) : 1.5 m/s Makita Corporation responsible manufacturer declare that the following Makita Model 9564CV machine(s): Designation of Machine: Work mode : surface grinding with normal side grip Angle Grinder Vibration emission (a ) : 8.0 m/s...
  • Page 4 Keep children and bystanders away while 15. Do not overreach. Keep proper footing and operating a power tool. Distractions can cause balance at all times. This enables better control you to lose control. of the power tool in unexpected situations. Electrical safety 16.
  • Page 5: Grinder Safety Warnings

    Service power tool at maximum no-load speed for one 25. Have your power tool serviced by a qualified minute. Damaged accessories will normally break repair person using only identical replacement apart during this test time. parts. This will ensure that the safety of the power Wear personal protective...
  • Page 6 accessory’s rotation at the point of the binding. d) Always use undamaged wheel flanges that For example, if an abrasive wheel is snagged or pinched are of correct size and shape for your selected by the workpiece, the edge of the wheel that is entering wheel.
  • Page 7 Safety Warnings Specific Wire Brushing 32. Pay attention that the wheel continues to Operations: rotate after the tool is switched off. a) Be aware that wire bristles are thrown by the 33. If working place is extremely hot and humid, or brush even during ordinary operation.
  • Page 8: Functional Description

    To stop the tool, release the slide switch toward the "O FUNCTIONAL DESCRIPTION (OFF)" position. Speed adjusting dial CAUTION: For 9561CVH, 9562CVH, 9564CV, 9565CV Always be sure that the tool is switched off and • unplugged before adjusting or checking function on 1.
  • Page 9 clockwise or counterclockwise. Be sure to tighten the ASSEMBLY screw securely. To remove wheel guard, follow the installation procedure in reverse. CAUTION: For tool with clamp lever type wheel guard Always be sure that the tool is switched off and •...
  • Page 10: Optional Accessory

    attachment in the vent. 1. Lock nut wrench 2. Shaft lock 1. Pin 2. Vent 007363 To remove the wheel, follow the installation procedure in 005262 reverse. Dust cover attachment can be removed by hand. Installing or removing dust cover attachment NOTE: (Optional accessory) Clean out the dust cover attachment when it is...
  • Page 11 Operation with abrasive cut-off / diamond wheel (optional accessory) 1. Lock nut 2. Abrasive cut-off wheel/diamond wheel 3. Inner flange 4. Wheel guard for abrasive cut-off 007364 wheel/diamond wheel 010855 The direction for mounting the lock nut and the inner flange varies by wheel thickness.
  • Page 12: Optional Accessories

    If you need any assistance for more details regarding breakage and overheating of the motor may occur. these accessories, ask your local Makita Service Center. Do not start the cutting operation in the workpiece. •...
  • Page 16 Makita Corporation Anjo, Aichi, Japan www.makita.com 884674D229...

Comments to this Manuals

Symbols: 0
Latest comments: