Download Print this page

Makita 9560CV Instruction Manual

100 mm (4”), 115 mm (4-112”), 125 mm (5”)
Hide thumbs Also See for 9560CV:

Advertisement

a
9 5 6 1 C V
_ _ _
Angle Grinder
2.800 -
10,5001min
2 8 9
mm
( 1 1 318")
1
7
k g
( 3
7 Ibs)
518"
100
mm
(4")
MODEL 9 5 6 0 C V
115 mm (4-112")
MODEL 9 5 6 4 C V
100 mm (4")
MODEL
9 5 6 3 C V
125
m m
(5")
MODEL
9 5 6 5 C V
115 mm (4-112")
MODEL 9 5 6 1 C V
9 5 6 5 C V
I
2 , 8 0 0
~~
10,50O/min.
I
2 9 9 mm ( 1 1-314")
INSTRUCTION MANUAL
1 8
kg ( 4 . 0
Ibs)
518"
DOUBLE
INSULATION
SPECIFICATIONS
MODEL
1
No
load speed
(RPM)
I
Overall
lenqth
I
Net weiaht
1
Spindle thread
9 5 6 0 C V
1
2 , 8 0 0
10,5001min
1
2 8 9
m m
( 1 1 318")
1
1 7 k q ( 3 . 7 Ibs)
I
M I 0 x 1 2 5
9 5 6 3 C V
I
2 , 8 0 0
~
10,5001min.
I
2 9 9
mm
( 1 1 - 3 1 4 " )
1
1 . 8 ka ( 4 . 0
Ibsl
1
M I 0
x
1 . 2 5

Advertisement

loading

Summary of Contents for Makita 9560CV

  • Page 1 Angle Grinder (4”) MODEL 9 5 6 0 C V 100 mm (4”) MODEL 115 mm (4-112”) MODEL 9 5 6 1 C V INSTRUCTION MANUAL SPECIFICATIONS MODEL (RPM) load speed 9 5 6 0 C V 2 , 8 0 0...
  • Page 2: General Safety Rules

    GENERAL SAFETY RULES WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
  • Page 3 Avoid accidental starting. Be sure switch is tools with your finger on the switch or plugging in tools that have the switch on invites accidents. Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result injury.
  • Page 4 Specific Safety Rules Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury.
  • Page 5 The followings show the symbols used for ? . , .../ SYMBOLS tool. volts amperes herts alternating current no load speed Class Construction revolutions or reciprocation per minute...
  • Page 6: Functional Description

    FUNCTIONAL DESCRIPTION Switch action CAUTION: Before plugging in the tool, always check to see that the switch actuates properly and returns to the "OFF" position when the side of the switch lever is depressed. To start the tool, slide the switch lever to "I"...
  • Page 7 ASSEMBLY Installing and removing wheel cover Installing Pull the lever in the direction of the arrow after loosening the screw. Install the wheel cover on the bearing box by adjusting the convex of the wheel cover to the concave of the bearing box. Turn the wheel cover by 180 degrees.
  • Page 8: Operation

    15" workpiece surface. During the break-in period with a new wheel, do not work the grinder in the direction or it will cut into the workpiece. Once the edge of the wheel has been...
  • Page 9 To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjust- ment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. tool...
  • Page 10 ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present The accessories or attachments should be used only in the proper and intended manner.
  • Page 11 742074-8 742075-0 7420768 (For abrasive disc) 9565CV Wire cup brush 75 For Model Wire bevel brush 85 9560CV 9563CV Wheel guard assembly (For cut-off wheel) For Model Part 3561CV 3564CV E65CV Part No. For Model 9565CV 9565CV 9560CV. 9563CV 192476-6...
  • Page 12 For masonry and concrete. For steel and cast iron. Knotted-Twist Wire cup brush 9564CV Lock nut wrench 9565CV Grip Part No. 152490-4 For Model For use For Model 9560cv 9563CV For Model 9561CV 743212-A 9564CV 9565CV Part No. ForModel 9561 CV 9565CV...
  • Page 14 SWITCH STll5A-40 COVER SWITCH LEVER COMPRESSION SPRING 4 NO USED ITEM NO DESCRIPTION BRUSH HOLDER MOTOR HOUSING MAKITA LABEL SWITCH KNOB CORD GUARD 8 POWER SUPPLY CORD REAR COVER TAPPING SCREW 4x18 INDICATION LABEL CONTROLLER A C CARBON BRUSH CB-318...
  • Page 15 MAKITA LIMED ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted t o be free of defects from workmanshlp and materials for the period of ONE YEAR from the date of original purchase.

This manual is also suitable for:

9563cv9561cv9565cv9564cv