Modine Manufacturing Model FC series Installation And Service Manual page 7

MECHANICAL SPECIFICATIONS / UNIT
Dampers (optional equipment)
When specified, the unit shall be equipped with a 25% or 100%
galvanized steel fresh air blade damper. Model FC, floor units
only.
When dampers are specified, indicate one of the following:
1. These dampers shall be controlled from the end pocket
with a manual control assembly that indicates the open and
closed positions.
2. The damper shall be controlled by an electric, spring-return
type motor, which will be energized when the blower motor
is turned on thus moving the damper to the 25% or 100%
position. It will be de-energized and close the damper when
the blower motor is off.
Table 7.1
1 & 2 Row Unit Data Specifications
Unit Size
Coil
Standard – 1 Row Face Area, Ft.
High Capacity – 2 Row Face Area, Ft.
Standard Coil Connections . . . . . . . . . . .
High Capacity Coil Connections . . . . . . .
Blowers (Direct Drive)
No./Dia. x Width (Inches). . . . . . . . . . . . .
High Speed (Rpm) . . . . . . . . . . . . . . . . . .
Low Speed (Rpm) . . . . . . . . . . . . . . . .
➀
High CFM . . . . . . . . . . . . . . . . . . . . . . . . .
Low CFM . . . . . . . . . . . . . . . . . . . . . . .
➀
➁ ➂ Motor HP. . . . . . . . . . . . . . . . . . . . . . . . .
Volts/Phase/Hertz. . . . . . . . . . . . . . . . . . .
Amps, Standard Shaded Pole Motors . . .
Amps, PSC Motor . . . . . . . . . . . . . . . . . .
Amps, High Static Motor . . . . . . . . . . . . .
Unit Weight – Lbs.
Model FC . . . . . . . . . . . . . . . . . . . . . . . . .
Model WCC . . . . . . . . . . . . . . . . . . . . . . .
① Standard solid state speed control offers infinite speed control between high and low speed/CFM.
② Sizes 002-006 have one motor. Sizes 008-014 have two motors.
➂ High Static Motors are .4 HP for sizes 002-006 and .8 HP for sizes 008-014.
Table 7.2
3 & 4 Row Unit Data Specifications
Unit Size
Coil
High Capacity - 3 Row Face Area, Ft. 2
High Capacity - 4 Row Face Area, Ft.2
High Capacity Coil Connections . . . . . . .
Blowers (Direct Drive)
No./Dia. x Width (Inches). . . . . . . . . . . . .
High Speed (Rpm) . . . . . . . . . . . . . . . . . .
Low Speed (Rpm) . . . . . . . . . . . . . . . .
➀
High CFM . . . . . . . . . . . . . . . . . . . . . . . . .
Low CFM . . . . . . . . . . . . . . . . . . . . . . .
➀
Motor HP. . . . . . . . . . . . . . . . . . . . . . . . .
Volts/Phase/Hertz. . . . . . . . . . . . . . . . . . .
Amps, High Static Motor . . . . . . . . . . . . .
Shipping Weight – Lbs.
Model FC . . . . . . . . . . . . . . . . . . . . . . . . .
Model WCC . . . . . . . . . . . . . . . . . . . . . . .
002 003
1.0 1.3
2
1.1 1.5
2
3/4" NPT 3/4" NPT
5/8" ID 5/8" ID
Sweat Sweat
1 / 5-1/4 x 7 1 / 5-3/4 x 7
1050 1050
625 625
250 330
150 195
1/30 1/30
115/1/60 115/1/60
1.7 1.7
.7 .7
4.4 4.4
85 90
90 100
002 003
0.9 1.2
0.9 1.2
3/4" NPT 3/4" NPT
1 / 5-1/4 x 7 1 / 5-3/4 x 7
1625 1625
1370 1370
260 340
200 260
0.4 0.4
115/1/60 115/1/60
4.4 4.4
85 90
90 100
AIR11-500.6
Motors, Blowers and Drives
Blowers shall be of the centrifugal, forward curved type, to
provide even air distribution and low sound level.
All units shall have shaded pole (permanent split capacitor
available when specified as optional equipment) direct-drive
motors. The motor and blower assembly shall be capable
of being easily removed from the unit. Motors are built for
continuous duty to NEMA standards.
Grilles (optional equipment)
When specified, aluminum linear bar inlet and/or outlet grilles
shall be provided.
When specified, outlet grilles may have two-way deflection louvers.
Filters
All air, both fresh and return, shall be filtered by a cleanable
expanded aluminum filter.
004 006 008
1.6 2.3 3.4
1.8 2.7 3.6
3/4" NPT 3/4" NPT 1" NPT
5/8" ID 5/8" ID 1" NPT
Sweat Sweat
2 / 5-1/4 x 7 2 / 5-3/4 x 7 3 / 5-3/4 x 7
1050 1050 1050
625 625 625
450 620 840
270 370 545
1/20 1/20 1/30 1/20
115/1/60 115/1/60 115/1/60
2.1 2.1 3.8
1.05 1.05 1.75
4.4 4.4 8.8
105 125 185
115 135 205
004 006 008
1.5 2.3 3.6
1.5 2.3 3.6
3/4" NPT 3/4" NPT 1" NPT
2 / 5-1/4 x 7 2 / 5-3/4 x 7 3 / 5-3/4 x 7
1625 1625 1625
1370 1370 1370
470 650 880
360 500 730
0.4 0.4 0.8
115/1/60 115/1/60 115/1/60
4.4 4.4 8.8
105 125 185
115 135 205
010 012 014
3.4 4.6 4.6
3.6 4.8 4.8
1" NPT 1" NPT 1" NPT
1" NPT 1" NPT 1" NPT
3 / 5-3/4 x 7 4 / 5-3/4 x 7 4 / 5-3/4 x 7
1050 1050 1050
625 625 625
1050 1240 1430
685 805 930
1/30 1/20 1/20 1/20
115/1/60 115/1/60 115/1/60
3.8 4.2 4.2
1.75 2.1 2.1
8.8 8.8 8.8
185 210 210
205 240 240
010 012 014
3.6 4.6 4.6
3.6 4.6 4.6
1" NPT 1" NPT 1" NPT
3 / 5-3/4 x 7 4 / 5-3/4 x 7 4 / 5-3/4 x 7
1625 1625 1625
1370 1370 1370
1100 1300 1500
920 1080 1250
0.8 0.8 0.8
115/1/60 115/1/60 115/1/60
8.8 8.8 8.8
185 210 210
205 240 240
7
7