Bosch GCM 12 GDL Professional Original Instructions Manual page 20

OBJ_BUCH-1464-001.book Page 20 Monday, May 9, 2011 3:47 PM
20 | English
76 Velcro strap
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Sliding Mitre Saw
Article number
3 601 M23 ...
Rated power input
No-load speed min
Reduced starting current
Laser type
mW
Laser class
Weight according to
EPTA-Procedure
01/2003
Protection class
Permissible workpiece dimensions (maximal/minimal) see page 24.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter
Assembly
Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material from the machine and the ac-
cessories provided.
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Sliding mitre saw with premounted saw blade
– Locking knob 15
– Dust bag 1
– Allen key 20
– Allen key 21
(below laser protection cap 27)
– Material clamp 22
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
1 609 929 Y62 | (9.5.11)
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Additionally required tools (not in delivery scope):
– Phillips screwdriver
– Open-end spanner (size: 8 mm)
GCM 12 GDL
– Ring, open-end or socket spanner (size: 10 mm and
Professional
... 680
Mounting the Locking Knob (see figure a)
... 640 ... 6B0
... 6L0 ... 6K0
– Screw the locking knob 15 into the corresponding drill
W 2000 1800
-1
3800 3800
nm 635 635
Stationary or Flexible Mounting
< 1 < 1
2 2
kg 32.1 32.1
Mounting to a Working Surface (see figure b1)
/II /II
– Fasten the power tool with suitable screw fasteners to the
Mounting to a Bosch Saw Stand
(GTA 2500 W, GTA 3700, GTA 3800) (see figure b2)
With the height-adjustable legs, Bosch GTA saw stands pro-
vide firm support for the power tool on any surface. The work-
mm 305
piece supports of the saw stand are used for underlaying long
mm 1.7–2.6
workpieces.
mm 25.4
– Mount the power tool in transport position on the saw
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dusts can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dusts, such as oak or beech dust, are considered as
carcinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be worked by specialists.
– Always use dust extraction.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
17 mm)
hole above the lever 16.
Always tighten the locking knob 15 firmly before saw-
ing. Otherwise the saw blade can become wedged in the
workpiece.
To ensure safe handling, the machine must be mounted
on a level and stable surface (e. g., workbench) prior to
using.
working surface. The mounting holes 12 serve for this pur-
pose.
Read all safety warnings and instructions included with
the worktable. Failure of observing safety warnings and
instructions can lead to electrical shock, fire and/or cause
serious injuries.
Assemble the worktable properly before mounting the
power tool. Perfect assembly is important in order to pre-
vent the risk of collapsing.
stand.
Bosch Power Tools