The Manhattan Ii Dac Standard Remote (Rc5) Setup; Technical Specification; Warranty; Important Safety Information - MyTek Manhattan II Owner's Manual

18

10.2 The Manhattan II DAC Standard Remote (RC5) Setup.

1. Turn the knob around until you see „Remote" menu then press the third button to activate the
menu.
2. Choose „RC5" option. „Remote Addr" appears on the left.
3. Activate „Remote Addr" menu by pressing the fourth button. The menu should be backlited with
blue colour.
4. Press any button on the RC5 compatible remote. The Manhattan II DAC will find the address
automatically
5. Done! - the remote is paired.

11. Technical Specification

ANALOG
• Analog Outputs Connectors: 2 XLR balanced outputs, 2 RCA unbalanced outputs
• Resolution DA: PCM 32bit / DSD up to 256 (11.2 Mhz)
• PCM Sample Rate: 44,1 / 48 / 88,2 / 96 / 176,4 / 192 / 384 Khz
• Dynamic Range: 130dB
• Output Impedance: 75 Ohm
• Headphone Amp: more than 500mA, 6 Watts
• High Current, High Slew Rate ultra low distortion, balanced
• Built-in Analog Preamp: Line level input or Phono M/M, M/C input, relay controlled
DIGITAL
• Computer Audio I/O: 2.0 Hi-Speed, data stream up to 480Mbits/384kHz, Type B, driverless.
• AES/EBU Input: XLR, 24Bits / 192 kHz, DSDx64 (DoP)
• TOSLINK Optical Input: up to 192kHz single wire
• S/PDIF Coaxial Input 1 & 2: up to 192kHz single wire, DSDx64 (DoP)
• SDIF DSD Input: DSD up to 256
• ADAT Input: up to 192kHz single wire
• WordClock I/O: BNC
• Clock: Mytek Femtoclock Generator (tm)" 0.82ps internal jitter, Wordclock Input and Output
(allows stacking multiple units for multichannel operation, includes mch DSD).
GENERAL
• Firmware: upgradable via USB Control panel, updates available online, periodic feature upgrades
• Power Supply: Internal switching PSU, 100 - 240 V AC
• External power supply: 12V, 4 - 6A / connector dimensions: 5,5 mm / 2,5 mm (inner pin)
• Dimensions [W x H x D]: 218 x 44 x 206 mm / 1U half rack
• Weight: 1,6 kg
Mytek Manhattan II DAC User's Manual

12. Warranty

Each individual Manhattan II DAC undergoes comprehensive quality control and a complete test before
shipping. This Manhattan II DAC is warranted by Mytek to the original purchaser against defects in
workmanship and materials used in manufacture for a period of two years from the date of purchase.
Faults due to customer misuse, unauthorized modifications or accidents are not covered by this
warranty. No other warranty is expressed or implied.
If you suspect that your product is faulty, please contact your local retailer. Prior to shipping customer
or retailer must obtain an RMA number from Mytek for warranty services. Units sent without RMA
number will not be accepted.
Mytek extends affordable repair service for all units manufactured to date that are

Important Safety Information

• Read, keep and follow these instructions.
• Connect all your devices before powering the unit.
• Do not expose this device to moisture, rain and liquid of any kind.
• Clean only with dry cloth.
• If any form of liquid or a forin object enter the device switch it off and unplug it from the power
source. Do not operate device until the foreign object is removed or the liquid has completly
dried. If in doubt please contact Mytek Digital.
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
19