Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for MyTek Stereo96ADC
Summary of Contents for MyTek Stereo96ADC
- Page 1 MYTEK DIGITAL.USA MASTERING ANALOG TO DIGITAL CONVERTER USER MANUAL VER.5/2005...
-
Page 2: Table Of Contents
Operation- Unbalanced Signal Source…….......10 For technical support, technical tips and support check: Sampling frequencies and External synchronization…..12 http://www.mytekdigital.com/products/stereo96adc.htm SuperShaper-HR ™ Noise shaping and dithering…..14 or contact Mytek tech support at: Rack mount shelf........….....17 info2005@mytekdigital.com Companion Stereo96 DAC……………………………..18 Specifications…………………………………………..19 or at: Warranty conditions……………………………………...20... -
Page 3: Introduction
"Internal jumper settings" for details. wordclock. The MYTEK Stereo96 series consists of two 1/3 rack units- the Stereo96 ADC and the Stereo 96 DAC. They are also a part of extended family of 1/3 rack units which also includes 192kHz capable converters, SRC and Studio Clock. - Page 4 Stereo96ADC internal trimpots and jumper assignments Stereo96ADC internal trimpots and jumper assignments (remove top cover to access) (remove top cover to access) Jumper JP5: Wordclock input 75 Ohm termination. Connect this jumper when Stereo96 ADC is the last destination in a chain fed by external wordclock source and the cable is long (above 6ft).
- Page 5 Mytek clock either through digital output 5. Select output wordlength- 24 bit full output is recommended. 16 and 20 signal or wordclock. In this configuration Mytek ADC serves as a very bit output are meant to be used when the destination (recorder such as stable low jitter house clock which increases the integrity and robustness CDR, ADAT tape machine) limits the wordlength.
- Page 6 When using internal trimpots analog input level needs to be aligned using an approx 1kHz sinewave fed from +4dB balanced source. The alignment Stereo96ADC can be operated with weaker consumer level unbalanced does not affect audio quality, only input sensitivity. The alignment is signal sources.
-
Page 7: Sampling Frequencies And External Synchronization
The quality of recorded signal signal or wordclock. In this configuration Mytek ADC serves as a very does not depend on how the digital destination is synchronized with stable low jitter house clock which increases the integrity and robustness Mytek AD converter. - Page 8 SuperShaper-HR ™ uses 9th order high resolution noise quality than 88.2k but the difference is very small and difficult to perceive shaping filters with proprietary filter coefficients developed by Mytek Inc. for most people. If the record is going to be mixed in analog domain, 96k The appropriate noiseshaping curve is programmed into noiseshaping might be a desirable choice for tracking.
- Page 9 More information about use of noise shaping in high resolution recording “Optimal Noise Shaping and Dither of Digital Signals” can be found in the following Audio Engineering Society Preprints ( http://www.aes.org ): Preprint Number: 2822 Convention: 87 1989-10 Author: Michael Gerzon “Coding Methods for High Resolution Recording Systems”...
-
Page 10: Rack Mount Shelf
The Stereo96 ADC is 1/3 rack space wide and 1U tall. Mytek provides a 1U rack mount shelf as accessory to mount up to 3 of 1/3 rack units. The units are attached to shelf with small screw connecting... -
Page 11: Specifications
Warranty Specifications This Stereo96ADC digital audio converter is warranted by Mytek to the original purchaser against defects in workmanship and materials used in Conversion: Linear, manufacture for a period of one year from the date of purchase. Faults due 128x oversampling at 44.1/48kHz to customer misuse, unauthorized modifications or accidents are not 64x oversampling at 88.2/96kHz...
Need help?
Do you have a question about the Stereo96ADC and is the answer not in the manual?
Questions and answers