Related Manuals for Adtec Edje-2000
Summary of Contents for Adtec Edje-2000
- Page 1 -2000 Real Time MPEG 2 Streaming Encoder CAT-008-H1.3 Adtec Digital 408 Russell Street Nashville, TN 37206 www.adtecinc.com 615-256-6619 615-256-7593 Fax...
-
Page 2: Table Of Contents
Table of Contents ............................2 Contacting Adtec Digital ..........................4 Edje 2000 Hardware ............................5 Introduction ............................5 Figure 1.1 Edje-2000 front view.........................5 Identifier..............................6 Figure 1.2 Edje-2000 rear view .........................6 Connector..............................7 Physical Concerns ..........................7 Non Rack Mount Applications ........................7 Rack Mount Applications ..........................7 Power Concerns ..........................8... - Page 3 Serial Communications ..........................34 RS232 Port ............................34 Communications Port Interface Adapter ..................34 Connecting to the Edje-2000 Via RS232 ..................... 35 Connecting use the GUI ......................... 35 Connecting to the Edje-2000 Via Ethernet ....................36 IP Configuration Tab ..........................36 Unit Setup .............................
-
Page 4: Contacting Adtec Digital
1-615-256-6619 Support Phone Support Fax 1-615-256-6593 http://www.adtecinc.com/support.asp Sales 1-615-256-6619 http://www.adtecinc.com/ Manufacturing and Engineering Florida Office 2231 Corporate Sq. Blvd. Jacksonville, FL 32216-1921 USA Shipping 1-904-720-2003 ext 227 International Sales 1-904-720-5274 International Fax Adtec Digital, Inc. USA Page 4 of 4... -
Page 5: Edje 2000 Hardware
This amazingly small MPEG 2 encoding appliance provides real time encoding, multiplexing and distribution without the use of a PC. The IP output is intended to be Uni-cast or Multi-cast to Adtec Edje-1010 or Edje-1013 Network MPEG Decoding Appliances or desktop MPEG decoding applications. -
Page 6: Identifier
Edje-2000 Real Time MPEG 2 Streaming Encoder Version 1.3 Table 1.0 Edje-2000 Front View Description Identifier Reset switch. Must be held for one second to initiate reset. Power LED, illuminates when +12 DC power is applied to unit. Video LED, illuminates during encoding. Video must be present to the selected input for encoding to start. -
Page 7: Connector
Physical Concerns Non Rack Mount Applications There are no physical orientation concerns when placing the Edje-2000 on a desk or tabletop. The Edje-2000 is designed to run in 90-degree Fahrenheit (32 Celsius) Non-condensing 70% relative humidity ambient conditions. Rack Mount Applications The Edje-2000 can be rack mounted in the optional rack shelf (Item 200- 024-1A-KIT). -
Page 8: Power Concerns
Power Concerns Power Supply The Edje-2000 ships with a 24-watt external switching power supply and six (6) foot standard SJT power cord with a three (3) pin US type plug. Optionally, a European 3 PIN cord with plug is available. The power supply carries the CE, UL, CSA and TUV safety certifications. -
Page 9: Introduction Summary
Real Time MPEG 2 Streaming Encoder Version 1.3 Introduction Summary The Edje-2000 was designed to provide high quality MPEG 2 Program Streams via IP networks or MPEG 2 Transport Stream via IP or ASI networks. It will provide many years of maintenance free high quality reliable MPEG encoding. -
Page 10: Installing The Edje-2000 Application
Edje-2000 Real Time MPEG 2 Streaming Encoder Version 1.3 Installing the Edje-2000 Application Install Screens Install Dialog Adtec Digital, Inc. USA Page 10 of 10... -
Page 11: Dialog Table Options
Edje-2000 Real Time MPEG 2 Streaming Encoder Version 1.3 Dialog Table Options Option Action No Questions-Asked Install Edje-2000 Application installed to default location. Select Component No Affect on install Advanced Options Install Select destination folders Do Not Install Cancel the installation process... -
Page 12: Application License
Click the Thanks option to complete the installation and see the installed shortcuts. A shortcut to launch the application will be placed on the desktop. Desktop Edje-2000 Icon Edje2000.lnk Double click the icon to launch the application. Adtec Digital, Inc. USA... -
Page 13: Start Menu Shortcuts
Edje-2000 Real Time MPEG 2 Streaming Encoder Version 1.3 Start Menu Shortcuts Edje-2000 Main Screen Adtec Digital, Inc. USA Page 13 of 13... -
Page 14: Using The Edje-2000 Application
Edje-2000 Real Time Encoder. It provides serial RS232 and Ethernet Telnet connectivity. A simple Units pull down menu option provides a means to create connection parameters and access them by name. Connecting to the Edje-2000 is essential to use the application. Adtec RS232 Serial Default Parameters Variable... -
Page 15: Connecting To The Edje-2000
PC to the Edje-2000. Connection Status Bar When a serial or Ethernet connection is established, the edje-2000 GUI must retrieve the current encoding status and parameters. During this process, “ATTEMPTING TO LOAD UNIT SETTINGS” will be displayed. -
Page 16: Adding A Unit
Enter a Unit Name; select the port, IP Address (Ethernet), Unit User Name (Ethernet), Baud Rate (Serial), and Unit Password (Ethernet). Once a Unit is added (created), the Unit will be available through the Connect To Pull down option. Adtec Digital, Inc. USA Page 16 of 16... -
Page 17: Video Settings
1-volt P-P video input to the BNC connector. The input automatically terminates. The YC video input requires a 75-Ohm source with 0.7-volt P-P Y (Luminance) and C (Chrominance) video input to the 4-pin din. Adtec Digital, Inc. USA Page 17 of 17... -
Page 18: Mpeg Type
(see Data Rate Format) Horizontal Resolution (HIS) Horizontal pixel resolution of the image the edje-2000 encodes. Provides a pixel sampling circuit that provides macro-block (16 lines) scaling before feeding the uncompressed digital video to the IBM eNV encoder. -
Page 19: Horizontal Spatial Filter (Hsf)
(with-in the image) in the horizontal plane. The filter uses an 8-Tap Polyphase filter for Luminance and a 4-Tap filter for Chrominance pixel values. Adtec currently uses the IBM coefficient values when setting HSF. -
Page 20: Horizontal Luma Bandwidth (Hsb)
Note: HSB can be adjusted while encoding. Vertical Resolution (VSI) Vertical pixel resolution. The edje-2000 provides a pixel sampling circuit that provides macro-block (16 lines) scaling before feeding the uncompressed digital vi deo to the encoder ASIC. Range is Full D1 NTSC, 480;... -
Page 21: Vertical Spatial Filter (Vsf)
2-tap temporal filter. The 2-tap filter allows pixel values of the current incoming picture to be weighted against the corresponding pixel values of the previous input picture. Adtec currently uses the IBM coefficient values when setting VTF. VTF Configuration Table Option Note: VTF can be adjusted while encoding. -
Page 22: Audio Settings
Thousands of bits per second. i.e. 192 Kbits is equal to 192,000 bits per second Note: The edje-2000 can optionally add a stereo input so that it can support two (2) stereo audio encodes or four (4) monaural audio channels. Each stereo input can individually be set to a different Data Rate. -
Page 23: Stereo Input 1 Type (Primary Audio)
Stereo Input 1 Data Rate (Primary Audio) Based on Audio Type Set the Audio Type the select the Data Rate by the pull down menu. Layer 2, 48 KHz, 224 K is the preferred broadcast setting. Adtec Digital, Inc. USA Page 23 of 23... -
Page 24: Secondary Audio (Sap)
Stereo Input 2 Data Rate (Secondary) Based on Audio Type Set the Audio Type the select the Data Rate by the pull down menu. Layer 2, 48 KHz, 224 K is the preferred broadcast setting. Adtec Digital, Inc. USA Page 24 of 24... -
Page 25: Multiplex Settings
Destination Program Stream Transport Stream Yes (Default) Yes (requires special IP compatible STB) Yes (Default) Hard Drive Adtec edje decoders, Soloist 2, Mirage and Duet decoders currently do not support Transport streams. Adtec Digital, Inc. USA Page 25 of 25... -
Page 26: Multiplex Type
When the Stop button is hit, a rename modal pops up, enter the designated eight-character file name at that time. Group Of Pictures (GOP) A GOP defines the image frame structure. GOP options for Program Stream multiplex. Adtec Digital, Inc. USA Page 26 of 26... -
Page 27: Gop Type
Lower latency version of long GOP that provides similar efficiency to IBBP Low latency GOP with poor efficiency I frame only GOP, very poor efficiency requiring very high data rates for quality images Adtec Digital, Inc. USA Page 27 of 27... -
Page 28: Gop Size
Carrier Per Channel (SCPC) service. The TMR rate will provide the modulator the required data rate to establish the desired Symbol Rate. The following settings are Transport Stream use only. MPEG PIDs Adtec Digital, Inc. USA Page 28 of 28... -
Page 29: System Information Pids (Si)
An arbitrary number used in the transport stream, typically 1 no need to be changed. IP Configuration Note: IP settings are only used with Program Streams and when the Multiplex is set to IP. Adtec Digital, Inc. USA Page 29 of 29... -
Page 30: Connected Units Ip Address
Multicast Mode Not MPEG 2 distribution via Ethernet. Send Send MPEG 2 via Ethernet UDP Unicast or Multicast. Multicast Send IP Address Adtec Digital, Inc. USA Page 30 of 30... -
Page 31: Multicast Send Port
Multicast. Ping IP address Type in an IP address and hit enter, the response will be shown in the dialog box. In Field Programming (IFP) Adtec Digital, Inc. USA Page 31 of 31... - Page 32 Real Time MPEG 2 Streaming Encoder Version 1.3 IFP provides a way to update the Edje-2000’s firmware. Simply browse for the xxxxxxxx.S19 record, select a Unit and click Program Application. Note: The Connect to pull down option has selected the Default COM 1 38400 connection, which used a PC’s Com Port 1 with a speed of 38, 400...
-
Page 33: Terminal
Real Time MPEG 2 Streaming Encoder Version 1.3 Terminal Terminal provides a very basic interface to send Terminal Commands to the edje-2000 RTE. See Appendix C for a list of API commands. Adtec Digital, Inc. USA Page 33 of 33... -
Page 34: Serial Communications
Computer connector DB9F to RJ-11 DB25 RJ-11 RJ-11 Notes Female Function Function Short to 7 inside 9 pin housing Transmit Receive No Connect Ground No Connect Short to 1 inside 9 pin housing No Connect Adtec Digital, Inc. USA Page 34 of 34... -
Page 35: Connecting To The Edje-2000 Via Rs232
1. Connect the 9 Pin to RJ-11 adaptor to the PC Communication Port. 1 (Com 1). 2. Connect the Adtec provided serial cable (RJ11 to RJ-11) to the adaptor and RS232 In on the Edje-2000. This is an industry standard modem cable that Adtec uses for serial RS232 communications. -
Page 36: Connecting To The Edje-2000 Via Ethernet
It is unlikely that the local network will be in the 192.168.10.xxx address range. Therefore a serial connection will be required to configure the Edje-2000 for the local network. A serial connection must be made then the Ethernet Variables can be modified in the edje GUI. -
Page 37: Unit Setup
IP Address. Please see your network administrator to obtain IP Address. 10.10.101.125 for this example User Name Telnet User Name. Default is ADTEC This case sensitive Password Telnet User Name. Default is NONE This is case sensitive Note: Since the Port is Network the Baud Rate is disabled. -
Page 38: Connecting The Edje 2000 Encoder To Edje 1013 Decoder
Audio from studio from studio Edje-2000 Encoder Console parameters 38,400 8 1 N Composite Video Un-Balanced analog to preview monitor Audio to preview monitor Edje-1013 decoder Console parameters 38,400 8 1 N Adtec Digital, Inc. USA Page 38 of 38... -
Page 39: Connecting The Edje 2000 To The Ip Express Router
Cross Over CAT 5 IPExpress ML CAT 5 CAT 5 CAT 5 Straight Straight Straight Through Through Through Console parameters 9600 8 1 N RJ-48 T1 RJ-48 T1 at CPE at CPE Adtec Digital, Inc. USA Page 39 of 39... -
Page 40: Terminal Commands
SETS VIDEO BIT RATE VBITRATE TRANSPORT MUX RATE TRANSMUXRATE TRANSPORT QUERY TRANSPORT TRANSPORTSTREAMID TRANSTREAMID VERTICAL SPATIAL FILTER VFILTERSPATIAL VERTICAL TEMPORAL FILTER VFILTERTEMPORAL VERTICAL OFFSET VOFFSET VERTICAL SIZE VSIZE VIDEO PID VIDEOPID VIDEO MODE VIDEO Adtec Digital, Inc. USA Page 40 of 40... -
Page 41: Glossary
D/A - Digital to Analog Converter. DAVIC - Digital Audio Visual Council. DBS - Direct Broadcasting Satellite or system. DCT - Discrete Cosine Transform. Temporal-to-frequency transform used during spatial encoding of MPEG video. Adtec Digital, Inc. USA Page 41 of 41... - Page 42 Elementary Stream. A bit stream that includes video, audio or data. It represents the preliminary stage of the Packetized Elementary Stream (PES). ETR - ETSI Technical Report. ETR 290 - ETSI recommendation regarding measurement of MPEG-2?DVB transport streams. Adtec Digital, Inc. USA Page 42 of 42...
- Page 43 Main Profile at Main Level. MPEG-2 specifies different degrees of compression vs. quality. Of these, Main Profile at Main Level is the most commonly used. MPEG - Moving Picture Experts Group, also called Motion Picture Experts Group. Adtec Digital, Inc. USA Page 43 of 43...
- Page 44 PSI tables include PAT, CAT, PMT and NIT. PSIP - Program and System Information Protocol. The ATSC protocol for transmission of data tables in the transport stream. Mandatory PSIP tables include MGT, STT, RRT, VCT and EIT. Adtec Digital, Inc. USA Page 44 of 44...
- Page 45 System Time Table. An ATSC PSIP table that carries time information needed for any application requiring schedule synchronization. It provides the current date and time of day and is located on PID 0x1FFB. Adtec Digital, Inc. USA Page 45 of 45...
- Page 46 VoD - Video on Demand. VSB - Vestigial Sideband Modulation. This is the terrestrial modulation method used in the ATSC. It can have either 8 (8VSB) or 16 (16 VSB) discrete amplitude levels. Adtec Digital, Inc. USA Page 46 of 46...
- Page 47 Edje-2000 Real Time MPEG 2 Streaming Encoder Version 1.3 Adtec Digital 408 Russell Street Nashville, TN 37206 www.adtecinc.com 615-256-6619 615-256-7593 Fax Adtec Digital, Inc. USA Page 47 of 47...