Adtec EN-31 Quick Start Manual

Thank you for your purchase of the Adtec
EN-31 Encoder/Modulator. This product is sold
with one or two encoder modules and with optional modulator hardware packages.
Some configurations may differ from the unit you have purchased if there is only
one encoder module installed. If you purchased this product without a modulator,
please disregard settings noted with an astericks.
Quick View Status
For information on the core systems of the encoder,
use the down arrow on the front panel to scroll
through these quick view menus.
Encoder Status TMR Auto Fill Encryption
ENCODING: 38.810Mb/s A/F: OFF CAS:BISS_1
TSI: 00001 SVC1: ON SVC2: OFF
Transport Stream ID Service 1 Service 2
Service1 ID Service1 Name Service1 Provider
SVC1: 00003 "AdtecHDTV1" Adtec Digital 1
SVC2: 00004 "AdtecHDTV2" Adtec Digital 2
Service2 ID Service2 Name Service2 Provider
Input 1: Resolution Frame Rate Source Mode
RES1: 1920x1080 25i INP: SDI MODE: AUTO
RES2: 720x480 59p INP: COMP MODE: SD
Input 2: Resolution Frame Rate Source Mode
Video Bit Rate CODEC Chroma
VRT1: 15000000b/s COD: MPEG2 CHR: 422
VRT2: 18242000b/s COD: H.264 CHR: 420
Video Bit Rate CODEC Chroma
Bitrate Type
Audio 1: 1 - 4
1:MU 384k 2:MU 384k 3:MU 384k 4:MU 384k
1:DD 192k 2:DD 192k 3:MU 384k 4:MU 384k
Audio 2: 1 - 4
Bitrate Type
Video1 PID Audio1 PIDs 1-4
VID: 0309 AUD:1: 0257 2: 0258 3: 0259 4: 0260
VID: 0308 AUD:1: 8180 2: 8181 3: 8182 4: 8183
Video2 PID Audio2 PIDs 1-4
RTP FEC Status Connector
TSoIP 1 - 4
1: SEND ON BUR GIGE 3: SEND OFF OFF GIGE
2: SEND ON OFF GIGE 4: OFF OFF OFF GIGE
ASI Remux Status Programs on Input
REMUX: ACTIVE PROGRAMS: 7
INPUT: 038.963Mb/s RESERVED: 040Mb/s
Input Data Reserved Bandwith
*Modulator Status Mod FEC Power Roll O
TX: Enable 32APSK_9/10 Pwr: -30dB RO: 25%
Freq: 1291MHz DVB-S2 Sym: 15.00Ms Pilot: ON
Frequency Mode Symbol Rate Pilot
Adtec Digital US Sales +1-615-256-6619 International Sales +1-904-394-0389
EN-31
Dual Channel Capable DSNG Encoder / Modulator
Services
TS Mux Rate
LED Status
Auto ll
Video
Blinking - No Video is detected
Tables
On - Video is detected
Encode TSID
Off - Device is not encoding
ASI Mode
On - Device is encoding
AVC
ASI Remux
Off - MPEG2 module installed
<< Ch1 - Ch2 >>
On - MPEG4 (H.264) module
installed
Active
HD
Off - Video Input is SD resolution
Service Name
On - Video Input is HD resolution
Svc Provider
A1 - A4
Off - Audio mode set to OFF
Program #
On - Encoding or Passthru audio
Logical Ch #
Blinking - Audio is active but there
is no source
Bars,Tones,ID
Alarm
Off - No system alarms
On - System alarm
BISS
Off - Encryption config is OFF
On - Encryption config is ON
Link
Modulator Line-UP *
Off - No network detected
This feature enables the operator to quickly view and/or configure select modulator
On - Connection active
RF output parameters. The parameters available in this menu are;
Busy
Off - No network activity
Carrier Mode: [PURE_CARRIER or MODULATED]
Use SELECT Button to toggle.
On - Network traffic present
Transmit: [ENABLED or DISABLED]
Use ENTER Button to toggle.
Reset:
Should you need to reset your
device, you can do so via the front
panel by pressing the MODE, ESCAPE
and RIGHT ARROW keys
simultaneously.
Video Encode AVC
HD
A1
A2
A3
EN-31
Dual MultiCODEC
Encoder/Modulator
A3
A2
A1
Video AVC HD
Encode
www.adtecdigital.com
*RF Tx IP Tx Video
Transmit << 1 - 4 >> << Ch1 - Ch2 >>
Type Mode Input
Mode IP Tx Mode SDI Mode
Local Oscillator Tx IP Address Chroma
Uplink Freq Tx Port Video Rate
Frequency(MHz) DVB per IP Aspect Ratio
Power(dBm) RTP AFD
Spectrum Invrsn FEC Mode GOP Type
Fec Frame FEC L GOP Structure
Roll O FEC D GOP Size
Pilot FEC TOS bits Fault Mode
Rate Priority Type of Service Fault Resolution
Symbol Rate TTL
Interface Rate Tx Connector
Carrier Mode Service Select
10 MHz Clock Mux Rate Mode
Clock Comb. Multicast Rate
For access, press the F1 and F2 keys simultaneously.
Output Power: [ in 0.5dB increments ]
Press or hold UP or DOWN arrows to adjust.
Uplink Frequency: [ in 1.0MHz increments ]
Press or hold LEFT or RIGHT arrows to adjust.
Carrier Mode Output Power
Carrier: PURE_CARRIER Power (dBm): -50.0
Tx: ENABLED Uplink (MHZ): 950.000
Transmit Uplink Frequency
A4 ENCODING:20.000M A/F:ON CAS:BISS_1 ENCODING:20.000M A/F:ON CAS:BISS_1
Alarm
BISS
TSI:00001 TSI:00001 SVC1:ON SVC1:ON
Link Busy
A4
Audio PIDS VBI
Video
Audio
<< Ch1 - Ch2 >> Source
ENC1 ENC2
<< 1 - 2 >> PMT PID Closed Cap.
Surround Mode PCR PID
<< 1 - 4 >> Video PID
Input Audio 1 PID
Model Indicators:
Mode Audio 2 PID
Type Audio 3 PID
No modulator
Rate Audio 4 PID
IF/LB/10M modulator
Level Teletext PID
Sync AMOL PID
Model Variety:
Format VITC Mode
Adtec offers MPEG2 and MPEG4 encoder
IFB VITC PID
modules. Depending on the type and
quantity of modules purchased,
SDI Pair Splice Mode
configurations may vary.
SDI Clock Source Splice PID
ECC
Front Panel Menus:
SDI Audio Grp.
Use Mode Button to move
MODE
through top layer menus.
Use arrows for navigation
in submenus.
Special Keys:
Use the F2 button as a decimal.
F2
SVC2:ON SVC2:ON
Quick Start Guide
Pro le CAS System
Select Mode Login
Save Clear SW Duration
Delete Encrypted SW Network Menu
User ID 1 Time Menu
User ID 2 NTP Menu
Alarm
SNMP Menu
COM2
Feature Menu
Hardware Info
Name
Firmware
Backlight
Use select to enter into edit
mode and enter to
SELECT ENTER
save selection.
Units ship with the front panel
logged in by default. If you become
logged out and are prompted for a
password, use the following key
sequence for access.
Press <Select> when panel displays
'User Login -- logged out'
Press <Up arrow>
Press <Select>
Press <Enter>
Press <Right arrow>
Press <Enter>
2015 Adtec Digital