AEG Favorit CE Instruction Book page 37

Water Hardness Settings:
When calling service functions, generally no rinsing program may be selected!
General Information
w Setting and adjusting the water hardness range is identical
with all designs and/or key arrangements.
w Always use the keys S0, S1 and S2, independently
of their model-related program assignment.
Generally applicable:
w Key S1 is ALWAYS the "Water hardness range key"
w In the works, hardness range value WH3 has been preset.
w With setting „WH1" no regeneration is usually carried out.
No adding of salt is required.
Any salt LED available will not be activated.
w Table of hardness range values:
General explications to key LED LD2* :
w This key LED goes on or flashes only if
the function "Rinsing agent stop" is programmed
on a certain machine model.
If the backlit function is not available on a certain
model, the respective LED is switched off in the mode Service Functions.
Calling / Modifying / Storing the Hardness Range Value
1.
S1
S2
b l i n k e n
2.
S1
LD1
LD2
S2
3. S1
LD1
LD2
5 s e k . l e u c h t e n
4.
LD1
3x blinken
5.
LD1
5 s e k . A u s
6.
LD1
3x blinken
7.
LD1
W i e d e r h o l u n g d e r b l i n k e n d e n
Wasserhärte-Anzeige bis ...
LD0
... AUS nac h 6 0 s e k . a u t o m a t i s c h
. . . A U S d u r c h m a n u e l l e B e t ä t i g u n g ü b e r E i n / A u s
Calling the function "Water hardness settings"
1. Press keys S1 and S2 simultaneously and ...
2. ... Keep them pressed until the machine is switched on
with the ON/OFF key S0. For acquittal, the respective key LED's
LD0
LD1 and LD2* are flashing (LD2* is only flashing if rinsing agent stop has been
programmed - see explanation opposite)
S0
3. Press the key S1 in order to call the water hardness function.
4. The acquittal LED LD1 lights up for 5 seconds.
LD0
5. Now the hardness range setting is displayed by
the key LED LD3 flashing:
(In the example left, WH3 is displayed by 3 times flashing)
6. / 7. This LED will then go dark for about 5 seconds ...
LD0
The operation is repeated on display for a maximum of 60 seconds.
(3x flashing – 5 sec pause – 3x flashing – 5 sec pause – etc.)
LD0
p r o T a s t e n d r u c k
LD0
A .
LD1
S1
LD0
5sek. leuchten
B .
LD1
X+1x blinken
C.
LD1
Storage of the water hardness settings
The hardness range selection is stored immediately upon each single input.
LD0
Exiting the function
S0
After 60 seconds after the last pushbutton operation on key
S1 or by switching the machine off by use of the ON/OFF key
S0, you automatically leave the special program.
Changing the preset hardness
A Press the key S1 to modify the
hardness range. The value is increased in
rotating manner.
B After pressing the key, the key LED LD1 will
go dark for about 3 seconds.
C The new value is then displayed by coded
flashing of LED LD1.
Further sequence as described under 6./ 7.
Any pressing of the key S1
will increase the hardness range rotatively.
(WH1, WH2 ... WH5, WH1, WH2, ...)