Safety Instructions 安全说明 该产品应由具有相应资质或经过培训的人员,遵守相关安全应 The products may be assembled and installed exclusively by 用规范进行安装。 suitably qualified and trained specialists duly observing all ap- Stäubli不承担由于不遵守这些警告而产生的任何责任。 plicable safety regulations. Stäubli Electrical Connectors (Stäubli) does not accept any li- ability in the event of failure to observe these warnings. Use only the components and tools specified by Stäubli.
Page 3
Explanation for MC3 工具说明-MC3 (ill. 1) (ill. 1) 压接钳 PV-CZM-16100A Crimping pliers PV-CZM-16100A incl. two interchangeable Locators 包括:两个可更换的定位块和两个可更 and two interchangeable crimping 换的嵌块。 inserts 2,5 / 4 / 6 mm Crimping range: 2,5 / 4 / 6 mm 压接范围: (14 / 12 / 10 AWG) (14 / 12 / 10 AWG) 32.6020-16100A Order No.:...
Page 4
Explanation for MC4 工具说明-MC4 (ill. 5) (ill. 5) Crimping pliers incl. locator PV-LOC 压接钳包括定位块PV-LOC和嵌块 and built-in crimping insert 1,5 / 2,5 / 4 mm Crimping range: 1,5 / 2,5 / 4 mm 压接范围: (14 / 12 AWG) (14 / 12 AWG) PV-CZM-18100 Type: PV-CZM-18100 型号: 32.6020-18100 Order No.:...
Exchanging the crimping 更换嵌块 inserts Removing the crimping insert 嵌块拆除 (ill. 17) (ill. 17) 闭合压接钳 Close the crimping tool (ill. 18) (ill. 18) Unscrew both the long S and the 卸下螺栓S(长)和S1(短),打开压 short S1 screw. Open the crimping 接钳(把钳子压到底后松口) tool (press completely together and release).
(ill. 23) (ill. 23) Rotate the locator (held magnetically) 转动定位块(会被磁铁吸住) (ill. 24) (ill. 24) Lock the locator. 卡住定位块 Crimping 压接 Example for ADBP3/... and 举例 ADBP3/... + ADSP3/... ADSP3/... (ill. 25) (ill. 25) 拆掉定位块,放入已剥皮的电缆,直到 Remove the locator. Insert the 绝缘层碰到嵌块。放入连接器金属端子 stripped cable on the left side until the 并将钳子压到底。...
(ill. 27) (ill. 27) Lightly press the pliers together so 慢慢闭合压接钳,直到金属端子固定 住。 that the crimping tabs lie securely within the crimping die. (ill. 28) (ill. 28) Insert the stripped cable until the 插入已剥皮的电缆,直到绝缘层碰到嵌 insulation comes into contact with the 块,然后把钳子压到底。 crimping insert.
Need help?
Do you have a question about the MA251 and is the answer not in the manual?
Questions and answers