Throttle Trim................11 Steering Rate ................11 Throttle End Point Adjustment ..........11 Calibrating ESCs ...............12 Standard Operation..............12 Using Your ET3 for the First Time ..........13 Low Battery Voltage Alarm ............13 General Care ................14 Maitenance ................14 Storage and Disposal ...............15 Troubleshooting Problems ............15...
For other adjustments it should be known that hobby grade radio controlled products such as those offered by IKONNIK differ from toy grade in that they are intended to be user-serviceable products where the user can program and maintain their own product. We try our best to ensure the information you need to introduce you to this form of product ownership is available to you though this manual.
Introduction The IKONNIK ET3 is a user-friendly 2.4GHz radio system that offers three channel operation - two proportional channels for steering and throttle and a handy switched third channel to control auxiliary functions or accessories.
2.4GHz Radio System Features Please read and understand the following instructions for your new radio system prior to operation to ensure a safe and enjoyable experience.
Page 7
Krypton Transmitter 1. Antenna (built in). 2. Steering wheel (CH1): Controls left / right motion. 3. Throttle (CH2) trigger: Controls the forward / reverse / brake motion (designed to be operated with index finger). 4. CH3 / Aux switch. 5. Hand grip. 6.
Be sure to follow the manufacturer’s care and use instructions. WARNING: THE ET3 TRANSMITTER IS NOT COMPATIBLE WITH LIPO BATTERIES CAUTION: LOOSE RECHARGEABLE BATTERIES MUST BE REMOVED FROM THE TRANSMITTER AND BATTERY HOLDER FOR RECHARGING. CHARGING THEM IN THE INCLUDED BATTERY HOLDER MAY CAUSE EXCESSIVE HEAT CAUSING DAMAGE TO THE HOLDER OR EVEN MELTING OF PLASTIC.
Krypton • Ensure there are no kinks in the antenna or antenna tube. • Never fold the end of the antenna over the tube, this will reduce the operating range of the system and damage the antenna. • Ensure the receiver is mounted securely or padded against hard impacts. Connection Channel 1: Controlled by the wheel, connect to a servo for steering.
The transmitter’s LED will begin to flash. When the LED on the transmitter and receiver stop flashing and light solid red, your ET3 transmitter and receiver will be bound / paired. You will now have full control of any channels that are connected.
Krypton Steering trim (CH1) Steering Trim Dial Use the steering trim dial to adjust the neutral point of the CH1 servo to ensure that your vehicle can track straight with no corrective steering input. When you install a servo always check the geometry of your linkages and make sure you start with the steering trim dial in the center position.
2.4GHz Radio System Brake Adjustment Push the trigger forward to full brake and use the ‘LO’ dial to adjust the brake end point to the desired location. • For fuel powered vehicles with brakes this will be past the closed position of the carburetor (engaging the override spring).
‘hands-off’. Low Battery Voltage Alarm If the transmitter battery voltage drops to 4.1V the power / bind indicator (12) will flash and the ET3 emit a beeping sound.
2.4GHz Radio System General Care • Always use clean, dry cloth or soft bristle brush to clean your equipment. • Never use chemical cleansers to avoid damage to the sensitive electronics and plastics. Maintenance We want you to enjoy your product to its fullest potential. For this to happen it is important to keep your product clean and properly maintained.
Krypton Storage and Disposal Storage • Always store all equipment in a cool dry place when not in use. • Always disconnect the batteries before storage. • Never store the transmitter or receiver in direct sunlight for extended periods of time. •...
IKONNIK product. If you purchased your IKONNIK product from a HobbyTown® internet site not affiliated with a local store, please consult that site for its service policies.
Page 17
Krypton JPerkins Distribution Warranty Information Guarantee This product is covered by the current statutory guarantee regulations. If you wish to make a warranty claim, please contact the model shop where you originally purchased the product from. You should also present your proof of purchase.
Page 18
2.4GHz Radio System Model Engines Warranty Information HELION RC 60 DAY WARRANTY Model Engines (Aust.) Pty. Ltd. warrants this product to be free from defects in materials or workmanship for 60 days from the date of purchase and will repair, replace or refund the purchase should the product prove to be defective.
European directives. This product’s design fulfils the protective aims of the European Community relating to the safe operation of this equipment. For a copy of the Declaration of Conformity, please visit: www.IKONNIK-rc.com/support Disposal Electrical equipment marked with the crossed out wheelie bin symbol must not be disposed of in household waste, but must be taken to a specialist disposal or recycling system.