Accusonic 8510+ series Reference Manual page 111

Index
7600 transducer assembly image, B-14
7600 transducer image, B-14
7600 transducer maintenance, B-8
7601 transducer maintenance, B-4
7605 stainless steel transducer image, B-15
7625 PVC transducer image, B-15
7630/34 internal mount transducer image, B-16
8510 More system parameter, 6-3
Accuflow file menu, 6-2
Accuflow interface
Configure menu, 6-2
connecting to PC, 6-1
Exit - File menu, 6-2
file menu, 6-2
Load Parameters - File menu, 6-2
Save Parameters - File menu, 6-2
system parameter - analogy outputs, 6-2
System Parameters - Configure menu, 6-2
Accusonic interfacd
show differences - Operate menu, 6-6
Accusonic interface
8510 More system parameter, 6-3
change flowmeter model, 6-3
connect, 6-4
contact closures, 6-3
disconnect - Operate menu, 6-4
flowmeter reset - Operate menu, 6-5
get flowmeter version - Operate menu, 6-5
graph data - Operate menu, 6-5
level input parameters, 6-3
Operate menu, 6-3
path parameters, 6-3
path variables - Operate menu, 6-4
receive parameters - Operate menu, 6-4
scope mode, 6-6
section parameters - Configure menu, 6-3
set meter clock - Operate menu, 6-6
set volume - Operate menu, 6-5
transmit parameters - Operate menu, 6-4
Alarm Relay Parameters, 5-5
Alternative Crossed Path Configuration in Open Channels, 3-4
analog level input, 2-5
analog out scaling ystem parameter, 7-1
analog output parameters, 7-7
Analog Output Parameters, 5-5
analog outputs, 2-5
analogy outputs - system parameter, 6-2
auto store par system parameter, 7-2
baud rate
setting, 7-9
build history Scope mode, 6-7
cabling checkout, 4-4
change flowmeter model, 6-3
clock, set - Operate menu, 6-6
Coil/status signals, C-5
compliance
FCC
Part 68, 2-4
configuration
layer boundary parameters, 7-11
special, 7-11
Conformity with EMC
EMC directive emission, 2-3
EMC directive immunity, 2-3
low voltage directive, 2-3
connect menu, 6-4
connecting to a PC, 2-8
contace closures, 6-3
continuous Scope mode, 6-6
data display, 2-7
data file types - Datalog menu, 6-11
data files, types - Datalog menu, 6-9
data log setup - Datalog menu, 6-10
Datalog menu
data file types, 6-11
data files, 6-9
data log setup, 6-10
retrieve logged data, 6-10
translate logged data, 6-8
date/time set, 7-9
description, principles of operation, A-1
detection methods - system parameters, 7-2
disconnect - Operate menu, 6-4
display retrieved log View menu, 6-8
display saved waveforms View menu, 6-8
display units system parameter, 7-2
display variables Scope mode, 6-6
Electrical Specifications, 2-1
EMC Conformtiy, 2-3
English/metric parameter, 7-1
equation for open channels and partially full pipes, A-4
equation for pipes, A-3
equation for pipes and channels with one path submerged, A-4
equation for pipes and conduits partially full equation, A-5
FCC
Part 68, 2-4
FCC Compliance, 2-4
Part 68, 2-4
firmware updates, 7-9
flow ave lvl system parameter, 7-2
Flow Computation
Alternative Crossed Path Configuration in Open Channels, 3-4
compound mode, 3-1
Compound Modes, 3-2
Manning Equation, 3-2
Manning Mode, 3-2
Non-Surcharged Multi-Path Trapezoidal Integration Mode, 3-3
Non-Surcharged Single Path Trapezoidal Integration Mode, 3-2
Overview, 3-1
pipe mode, 3-1
Pipe Mode, 3-5
Single Path Trapezoidal Integration, 3-2
Surcharged Integration, 3-2
Surcharged Mode, 3-4
Volume Calculation, 3-6
Water Temperature Calculation, 3-6
flow scaling system parameter, 7-1
flowmeter reset - Operate menu, 6-5
get flowmeter version - Operate menu, 6-5
good section, 7-12
graph data - Operate menu, 6-5
image
In-1