JUKI SC-922 Instruction Manual page 48

07 Selection of alternate up/down initial output (function setting No ..
147)
Alternate up/down output is forcibly turned ON or OFF when the
p~wer
IS
turned ON. . .
When this function is set to disable, the alternate up/down output
IS
restored to the state
m
wh1ch the func-
tion has been set before the last turn-OFF of the power.
When the set value is "1," the alternate up/down output is brought into the OFF state. When the set
value
1s •2." the output is brought into the ON state.
01 1
fill]
01 I I
0
I
0 Disabled
1. OFF
2
ON
2-pltch output during reverse feed stitching at the beginning/end of sewing (function setting No. 148)
2-p1tch output Is set in the ON state during control of reverse feed stitching at the beginning/end of sewing.
Dlilli::!J DCOQJ
0 : The funct1on is
~n
the OFF state
1 :
The function
IS
m the ON state
®
2-pitch output Inversion during alternate up/down output (function setting No.
149)
The 2-p1tch output status
IS
output with inverted in synchronism with the alternate up/down output.
2-p1tch output is changed over to "OFF" if it is set in the ON state or to "ON" if it is set in the OFF state
when changing over the alternate up/down output.
DfTii:I!JDD
@]
0:
The function is in the OFF state
1 : The function is in the ON state
2-pitch Initial output selection (function setting No. 150)
2 -p1tch output is forcibly turned ON or OFF when the power is turned ON .
When this funct1on is set to d1sable, the 2-pitch output is restored to the state in which the function has
been set before the last turn-OFF of the power.
When the set value is
"1,"
the alternate up/down output is brought into the OFF state. When the set value
is "2," the output 1s brought into the ON state.
0
1
I s
m
0 I I
(iJ
0 Disabled
1 OFF
2
ON
I
Pause and stitch
alignme~t
function (function setting No.
151)
When the reverse feed slltch1ng/mult1-layer stitch 1 ng is specified, the sewing machine temporarily stops at
every corner of the sewing pattern at the beginning and end of sewing and during overlapped stitching.
(Caution) When this function is brought Into ON state, functions setting numbers 5
1
to 53 are disabled.
0[])] liJ OQ ' ] ]
0 : The function is in the OFF state Temporarily
1 : The function is in the ON state stops at these
points.
ln~~~:~:~;~~es!~~~lng
function for
begi~ninglend
of sewing (fun ction setting No.
154)
hi rl '"
9
machlne _ head provided With the condensation stitching function the sewing
ma·
c ne pe orms condensation slltchmg instead of t · '
This function should be used when you do not
w:~t~mallc
reverse feed stitching . event
thread from
shpp 1 ng off
the material at th b .
0
carry out reverse feed stitching but want to pr
r
e eglnnmg and end of sewing.
l 1l sllJ0[ I I o ]
0:
The function is in the OFF state
1 : The function is in the ON state
l
Needle thread g rasp ing function (fun ction sett· N
mg o. 156)
Selection between enable/disable of the needle th d . .
O
m
rea graspmg functiOn
fl s
m
DD=no
0
~ Enable/di~ab~e
is changed over With the operation enabling switch
1 · The function
IS
disabled
2
: The function is enabled.
-40-