JUKI SC-922 Instruction Manual page 47
Hide thumbs
Also See for SC-922:
- Instruction manual (58 pages) ,
- Engineer's manual (82 pages) ,
- Supplementary instructions manual (160 pages)
Table of Contents
Advertisement
~
Function added to the needle up
I
down compensating switch
(Func
tion setting
No.
93)
Operation
of
needle up/down compensating switch is changed after turning ON the power or thread trimming.
01~
9
13
I
ODC[QJ
0 :
Normal (needle up/down compensating stitching only)
1
:
One stitch compensating stitching
is
performed only when aforemen-
tioned changeover
is
made.
(Upper stop
I
upper stop)
2 :
Needle-down function operates after thread trimming.
3
:
Function of needle-down with
operation of
2 plus
presser
lowering
op-
eration and needle-up with thread trimming
operation
is added.
29
Continuous
stitching +one shot stitching nonstop fun ction (Function setting
No.
94)
This function
is
used to proceed a step to the next one without stopping the sewing machine at the end
of
the
step
when performing sewing with the
cont
inuous sewing and one-shot
sewing combined
using the
programming function of the operation panel IP.
DDIIIIJ 00[]]]
0
:
Normal (Stop when a step has
completed.)
1
: The sewing machine proceeds to next
step
without
stopping
after
a
step has
comp
leted.
QO
Setting of
max.
number of rotation of the sewing machine head (Function setting
No.
96)
This funct1on can
set
the max. number of rotation of the sewing machtne head you desire to use.
Upper lim1t
of
the
set
value varies in accordance with the sewing machine head to be
connected.
01
I9IIJ
II[()
...Q...]J
150 to Max. [stilmin] <50
I
sti/min>
31
Main shaft reference angle compensation (Function setting
No.
120)
Main
shaft
reference angle
is
compensated
[J[L"2
o
J
01 I I I
0
I
Setting range
-
so
to
so·
<1
1 ·>
32
UP position starting angle compensation (Function setting No.
121)
Angle to detect UP pos1tion start1ng
is
compensated.
DDJiliJ OLIJiJ
Setting range
-
15 to
15•
<1
I·>
33
DOWN position starting angle compensation (Function setting
No.
122)
Angle to detect DOWN position starting is compensated.
DITJ@J[2]
ODLIQJ
Sett1ng range
- 15 to
15•
<1
t•>
~
Setting of energy saving function during standby (Function setting
No.
124)
It
is
possible to reduce power consumption while t he sewing machine is 1n standby
state.
It should be noted
that the
startup
of the sewing machine may delay for a moment
if
this function 1s set.
DlJl!IIIJ
DO[
[OJ
o
:
Energy-sav!ng mode ~s
ineffe~tive.
1
·
Energy-sav1ng mode
IS
effect1ve.
~
Number of stitches setting for automatic cancellation of alternate up/down output (function set-
ting
No.
144)
Alternate
up/down
output is cancelled when the set number of
stitches
has been sewn
(0:
Automatic
can-
cellation is
disabled). After the alternate up/down output is output by the set
number of stitches,
output is
turned OFF. When
"0" is
set, this function does not
work.
(However, the number
of
stitches actually
sewn
may be larger than the set one according to the sewing speed.)
W
[ij[i) [O[l
O
0
:
Automatic .cancellation
is
disabled
~
1 : 1-
30
(1
st1tch)
36
Selection of alternate up/down output after thread trimming (function setting
No.
146)
Alternate up/down output 1 s forcibly turned ON or OFF after thread trimming
.
When this function
is
set to disable, the alternate up/down output retains the
state
before thread
trimming.
When the set value is
"1,"
the alternate up/down output is brought
into
the OFF
state.
When the set
value
is
"2,"
the output is brought into the ON state.
OD:::EIIJ ODCTIJ
0
:
Disabled
1
:
OFF
2
:
0N
-39-
Advertisement
Table of Contents
