Related Manuals for Clarke YDH30
Summary of Contents for Clarke YDH30
- Page 1 30 LITRE DEHUMIDIFIER MODEL NO: YDH30 PART NO: 6479600 OPERATION & MAINTENANCE INSTRUCTIONS LS0916...
-
Page 2: Environmental Protection
INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. -
Page 3: Safety Warnings
3. This appliance is designed to dehumidify residential environments and must not be used for any other purposes. 4. If the appliance requires repair, always contact your CLARKE dealer. Always insist on original spare parts. Repairs carried out by unauthorized persons may be dangerous and invalidate the guarantee. -
Page 4: Electrical Connections
ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. -
Page 5: Before Use
BEFORE USE LOCATING THE DEHUMIDIFIER • Position the dehumidifier close to a mains supply socket. • Free space as shown must be left around the dehumidifier, so as not to block the air flow. • Make sure that the power cable is not placed where it can be inadvertently pulled or pinched and where it... -
Page 6: Control Panel
CONTROL PANEL Used to adjust Turns the the humidity dehumidifier on setting from 40% or off. - 70% (default 50%). Set the number Selects the of hours until the operating mode dehumidifier is also activates turned on or off. the child lock. Starts or stops Ultra quiet fan the swing... -
Page 7: Operation
OPERATION SWITCHING ON/OFF 1. Plug into the mains supply socket and switch on. • The dehumidifier will begin and the display will show the current humidity level and temperature of the room. 2. Press the POWER button to switch the dehumidifier ON. •... -
Page 8: Timer-On Setting (Auto Start)
TIMER TIMER-ON SETTING (AUTO START) 1. While the dehumidifier is NOT running: Press TIMER key repeatedly to set the length of time (1-24 hours) until the dehumidifier turns on. • The display will show the selected number of hours flashing on and off for 5 seconds and then stop flashing. -
Page 9: Mode Selection
MODE SELECTION Press the MODE key to cycle through the modes: Auto Press the humidity button repeatedly to select the Dehumidification required humidity level. • The humidity level can be set between 40% and 70% (5% increments) and set to 50% as default. -
Page 10: Ionizer Function
• Make sure that the front of the filter is facing towards you. • An optional HEPA filter (not supplied) is available from your Clarke dealer. 4. Replace the plastic filter making sure that all the lugs are seated correctly. -
Page 11: Emptying The Water Tank
EMPTYING THE WATER TANK 1. When the full water tank symbol on the control panel illuminates, switch off the dehumidifier and disconnect it from the mains supply. 2. Carefully remove the water tank by placing your fingers in the channel underneath the tank and pulling it towards you. -
Page 12: Internal Drying Cycle
INTERNAL DRYING CYCLE Run the internal drying cycle before storing the dehumidifier at the end of the season or If the dehumidifier has been used continuously for a long period of time. Running the cycle will remove water/moisture from the unit, preventing a build up of mildew which will affect the efficiency and life of the unit. -
Page 13: Maintenance
MAINTENANCE WARNING: ALWAYS UNPLUG THE DEHUMIDIFIER BEFORE PERFORMING ANY CLEANING OR MAINTENANCE OPERATIONS. STORAGE • Unplug from the mains socket and empty the tank. • Cover the dehumidifier to prevent dust getting inside. CLEANING THE CABINET • Use a soft damp cloth to clean the exterior. •... -
Page 14: Troubleshooting
TROUBLESHOOTING Cause Solution Dehumidifier Is power plug connected Insert power plug into socket does not run The water tank is full? Empty the water from the tank Water tank is not fitted Replace the water tank correctly. correctly. Dehumidifying Is room temperature or Dehumidifying capability will function does humidity too low? -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...