Related Manuals for Clarke YDE20
Summary of Contents for Clarke YDE20
- Page 1 20 LITRE DEHUMIDIFIER MODEL NO: YDE20 PART NO: 6470682 OPERATION & MAINTENANCE INSTRUCTIONS LS0916...
- Page 2 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 3: Environmental Protection
INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. -
Page 4: Safety Warnings
3. This appliance is designed to dehumidify residential environments and must not be used for any other purposes. 4. If the appliance requires repair, always contact your CLARKE dealer. Always insist on original spare parts. Repairs carried out by unauthorized persons may be dangerous and invalidate the guarantee. -
Page 5: Electrical Connections
ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. -
Page 6: Control Panel
CONTROL PANEL HUMIDITY button: Used to select the humidity level (or fan speed in Air Purify mode) TIMER button: used to adjust the Timer on / Timer off settings. MODE button: Cycle through the following operating modes Auto - High - Low - Air Purify Press and hold to select Drying Mode LOCK button: Used to activate or deactivate the key lock, thereby preventing accidental changes to the settings. -
Page 7: Before Use
BEFORE USE POSITIONING THE DEHUMIDIFIER • Position the dehumidifier close to a mains supply socket. • Free space as shown must be left around the dehumidifier, so as not to block the air flow. • Make sure that the power cable is not placed where it can be inadvertently pulled or pinched and where it does not cause a trip hazard. -
Page 8: Operation
OPERATION SWITCHING ON/OFF 1. Plug into the mains supply socket and switch on. • The dehumidifier will beep and the display will show the current humidity level. 2. Open the air outlet vent on top of the dehumidifier. 3. Press the POWER button to switch the dehumidifier ON. -
Page 9: Mode Selection
MODE SELECTION Press the MODE button repeatedly to cycle through the following modes: - Auto - High -Low - Air Purify AUTO When AUTO is selected, the user selects the humidity level required and the dehumidifier will turn on or off as required to maintain that level. 1. -
Page 10: Drying Function
DRYING FUNCTION If the dehumidifier has been used in a high humidity environment for a long period of time, or you do not intend to used the dehumidifier for a few weeks, you must run the drying cycle to remove water/moisture from the unit. This will prevent a build up of mildew which will affect the efficiency and life of the unit. -
Page 11: Emptying The Water Tank
EMPTYING THE WATER TANK 1. When the FULL indicator on the control panel illuminates, switch off the dehumidifier and disconnect it from the mains supply. 2. Carefully remove the water tank by placing your fingers in the channel underneath the tank and pulling it towards you. -
Page 12: Maintenance
MAINTENANCE WARNING: ALWAYS UNPLUG THE DEHUMIDIFIER BEFORE PERFORMING ANY CLEANING OR MAINTENANCE OPERATIONS. STORAGE • Unplug from the mains socket and empty the tank. • Cover the dehumidifier to prevent dust getting inside. CLEANING THE CABINET • Use a soft damp cloth to clean the exterior. •... -
Page 13: Troubleshooting
TROUBLESHOOTING Cause Solution No operation Power cable Insert the plug into a power disconnected. socket. Water tank is full. Empty the water tank. Water tank is not seated Replace the tank correctly in properly. position. Dehumidified Filter is dirty. Clean the filter as described volume is small See page 12. -
Page 14: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 15 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...