Related Manuals for Clarke DH10L
Summary of Contents for Clarke DH10L
- Page 1 10 LITRE DEHUMIDIFIER (R290) MODEL NO: DH10L PART NO: 6470687 OPERATION & MAINTENANCE INSTRUCTIONS DL1120 ISS 01...
-
Page 2: Environmental Protection
INTRODUCTION Thank you for purchasing this CLARKE 10 Litre Dehumidifier. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. -
Page 3: Electrical Connections
ELECTRICAL CONNECTIONS WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. -
Page 4: Safety Warnings
3. This appliance is designed to dehumidify residential environments and MUST NOT be used for other purposes. 4. If the appliance requires repair, always contact your CLARKE dealer. ALWAYS insist on original spare parts. Repairs carried out by unauthorized persons may be dangerous and invalidate the guarantee. -
Page 5: Technical Specification
TECHNICAL SPECIFICATION Power Source 230 Volts AC 50Hz Input Power 175W Dehumidifying Extraction Rate 10 litres/day Water Tank Capacity 2 Litres Air Flow Rate 80 m3/h Dimensions (LxWxH) 203 mm x 256 mm x 415 mm Weight 9.88 kg Operation Temperature C - 32 Refrigerant R290 (Hydrocarbon Propane) - Page 6 OVERVIEW Description Control Panel Air Outlet Water Tank 9mm Drainage Pipe Fold Down Carrying Handle Air Inlet and Filter Water Drain Plug and Outlet Power Cable & Plug Holder Power Cable Storage Hooks Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 7 SETTING UP & POSITIONING THE DEHUMIDIFIER WARNING: DO NOT USE OR STORE THE DEHUMIDIFIER NEAR A HEAT SOURCE, AS THE UNIT CONTAINS PRESSURISED FLAMMABLE REFRIGERANT GAS (R290-HYDROCARBON PROPANE) • Empty any water that is in the water tank before every use. •...
-
Page 8: Operation
OPERATION CONTROL PANEL 1 = TIMER (24HR SETUP) Press this button to set the length of time the dehumidifier runs for (1-24 Hours) via the LCD display. To cancel the timer, press the button twice once the timer is set. 2 = DRYING Press this button to start the dehumidifier drying procedure. -
Page 9: Select Mode
SELECT MODE SETTING OF TIMER - OFF • When the dehumidifier is running, press the TIMER button to adjust the time from 1 hour to 24 hours, pressing once for each hour. If the time exceeds 24 hours, the count will reset to 1 hour and will start the cycle again. -
Page 10: Emptying The Water Tank
• The dehumidifier will start at high air speed and release air continuously for 30 minutes. • The dehumidifier will reduce to low air speed and run for 20 minutes. HOW TO STOP • Press the DRYING button again to cancel the drying procedure, which will return the dehumidifier to the running state before the start of the drying procedure. -
Page 11: Continuous Draining
4. Before refitting the water tank, check to confirm the indicator float moves freely. 5. Refit the water tank. NOTE: The unit will not operate unless the water tank is fitted correctly. CONTINUOUS DRAINING This function enables continuous dehumidifying without having to empty the water tank. -
Page 12: Maintenance
MAINTENANCE WARNING: ALWAYS UNPLUG THE DEHUMIDIFIER BEFORE PERFORMING ANY CLEANING OR MAINTENANCE OPERATIONS. CLEANING THE CABINET • Use a soft damp cloth to clean the exterior. • Never use harsh chemicals or abrasive cleaning agents as these may damage the casing finish. •... -
Page 13: Troubleshooting
TROUBLESHOOTING Cause Solution No operation Plug fuse failure. Check fuse in plug and replace if necessary. Water tank is full or placed Check water tank and empty if incorrectly. necessary and/or check water tank positioning. The ambient temperature is This machine will not operate outside of these boundaries. -
Page 14: Display Codes
DISPLAY CODES Display Code Instruction Water Tank is Full. Empty Tank, See Page 9 Coil Sensor Detects Anomaly, Contact Your CLARKE Dealer for Assistance. Room Temperature Sensor Detects Anomaly, Contact Your CLARKE Dealer for Assistance. Unit is in Defrosting State (Normal) Unit is in Internal Drying State (Normal). -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the DH10L and is the answer not in the manual?
Questions and answers