Table of Contents
Advertisement
Quick Links
SERVICE MANUAL
STAINLESS STEEL HANDS FREE WALL TELEPHONE
WITH OPTIONAL ADA FEATURE
EQUIPPED WITH SPK1.07r1 FIRMWARE
Communication Equipment
& Engineering Company
FOR
MODEL SSW-521-F
(FORMERLY SSW-521-FS)
SSW-521-F-SPK1.07UNVLr1-ADA-ISSUE4.0
Serving the Telephone Industry Since 1930
519 W South Park Street
Okeechobee, FL 34972
Voice: 863-357-0798
Fax: 863-357-0006
Advertisement
Table of Contents
Related Manuals for CEECO SSW-521-F
Summary of Contents for CEECO SSW-521-F
- Page 1 SSW-521-F-SPK1.07UNVLr1-ADA-ISSUE4.0 SERVICE MANUAL MODEL SSW-521-F (FORMERLY SSW-521-FS) STAINLESS STEEL HANDS FREE WALL TELEPHONE WITH OPTIONAL ADA FEATURE EQUIPPED WITH SPK1.07r1 FIRMWARE Serving the Telephone Industry Since 1930 Communication Equipment 519 W South Park Street & Engineering Company Okeechobee, FL 34972...
-
Page 2: Important Information
ISSUE 4.0 IMPORTANT INFORMATION CUSTOMER Please fill in before you continue. The following information is necessary when calling CEECO for assistance. MODEL NUMBER MODEL SSW-521-F STAINLESS STEEL HANDS FREE WALL TELEPHONE EQUIPPED WITH SPK1.07UNVLr1 FIRMWARE. SERIAL NUMBER DATE MANUFACTURED LOCATION INSTALLED For us to better serve you, please have this information available when calling for technical support. -
Page 3: Table Of Contents
RECOMMENDED TOOLS AND TEST EQUIPMENT ........11 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS ....12 TESTING....................... 14 SPECIFICATIONS....................15 PARTS LIST ......................16 10.0 REPAIR AND RETURN INFORMATION............17 11.0 WARRANTY POLICY ..................18 12.0 DIAGRAM......................19 CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 4: Introduction
GENERAL The CEECO Model SSW-521-F Hands free telephone is a sturdy, vandal resistant, stainless steel speakerphone, with optional ADA feature (red/green LED for visual call progress indication). Instead of a hookswitch and handset, the telephone has a Press to start/Press to stop button (“CALL”... -
Page 5: Programming
Enter #00, followed by a series of ten (10) digits as selected from the following page. Location “00” is the telephone options location. By entering a selected number of 0-9 into each of the ten digit locations, the phone is customized for the particular installation CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 6: Programming Continued
1 Dial PBX/Acess number stored under #18. Digit 9: Always 0 for this model. Digit 10: No Wink Detect 1-9 Length of the Wink (l = 50ms incremental to 450ms. 5 is recommended) CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 7: Programming Continued
1 to 11 digits. There are twenty (20) memory locations available (#71-#89). Simply enter the intended memory location, followed by the desired/allowed calling pattern. Please refer to the example on the following page. CEECO Communication Equipment & Engineering Company PROPRIETARY... - Page 8 #88 _ - _ _ _ - _ _ _ - _ _ _ _ #79 _ - _ _ _ - _ _ _ - _ _ _ _ #89 _ - _ _ _ - _ _ _ - _ _ _ _ CEECO Communication Equipment & Engineering Company PROPRIETARY...
-
Page 9: Programming Continued
#30 and the phone will Speed Dial - 1-800- 555-1212. • Be sure to log your entries in the speed dial table on the next page for future reference. CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 10: Programming Continued
#68 _ - _ _ _ - _ _ _ - _ _ _ _ #49 _ - _ _ _ - _ _ _ - _ _ _ _ #69 _ - _ _ _ - _ _ _ - _ _ _ _ CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 11: Operation
If Digit 1 of Location #00 is set to "1", then there are no restrictions and any number may be dialed. RECOMMENDED TOOLS AND TEST EQUIPMENT Volt/Ohm Meter 5/16" Nut driver 3/8" Nut Driver Security Tool, CEECO Part Number 301-037 Flat Blade Screw Driver DTMF Test Set CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 12: Installation Notes And Assembly Instructions
Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. CEECO Communication Equipment & Engineering Company PROPRIETARY... - Page 13 ISSUE 4.0 TELEPHONE LINE WIRING DIAGRAM TERMINATE TIP & RING HERE CEECO Communication Equipment & Engineering Company PROPRIETARY...
-
Page 14: Testing
Preprogrammed speed dial numbers should automatically dial when the corresponding location code is pressed (i.e. #30). Note: If any trouble is encountered, repeat the appropriate programming section(s). If trouble persists, please refer to section 10.2. CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 15: Specifications
Via DTMF keypad. DIMENSIONS : 5"W X 10"H X 3 1/2"D WEIGHT : Approximately 6 Pounds RINGER EQUIVALENCY: 0.4A TYPE JACK : Over-voltage protected terminal strip UL LISTED NO.: 6OF5 FCC NO.: BWBUSA-73021-MT-E CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 16: Parts List
PARTS LIST QUANTITY PART NUMBER DESCRIPTION 301-018 MODULAR LINE CORD 301-054 MODULAR CONNECTOR (RJ11C) SERVICE MANUAL 700-008 KEYPAD CABLE 660-000 CEECO SPK BOARD 705-110 CONNECTORIZED KEYPAD 6020-B MOMENTARY PANEL SWITCH 14123 SPEAKER 12017 RINGER 11071 STAINLESS STEEL COVER 321-015 STAINLESS STEEL BACKPLATE 9023 1/4-20 X 3/4"... -
Page 17: Repair And Return Information
10.3 NON-WARRANTY REPAIR CEECO will repair equipment out of warranty for a set charge plus parts. The customer must pay the shipping costs for both directions. 10.4 RETURN FOR CREDIT Material may be returned for credit only with prior approval. Material authorized for return is subject to a 20% restocking charge based on the manufacturer's list price. -
Page 18: Warranty Policy
PRINTED CIRCUIT BOARDS Printed circuit boards should not be field repaired. If a unit is found to be faulty, replace it with another unit and return the faulty unit to CEECO for repair. Modifications by anyone other than CEECO will void the warranty. -
Page 19: Diagram
ON position BEFORE going off-hook. When programming is completed, move the mini jumpers to the OFF position. NOTE: Do not leave the mini jumpers in the ON position; this will decrease battery life. CEECO Communication Equipment & Engineering Company PROPRIETARY...
Need help?
Do you have a question about the SSW-521-F and is the answer not in the manual?
Questions and answers