Table of Contents
Advertisement
Quick Links
SERVICE MANUAL
MODEL SSW-521-D
STAINLESS STEEL HANDS FREE WALL TELEPHONE
WITH OPTIONAL ADA FEATURE
EQUIPPED WITH SPK1.07UNVLr1 FIRMWARE
Communication Equipment
& Engineering Company
FOR
(FORMERLY SSW-521-DS)
SSW-521-D-SPK1.07UNVLr1-ADA-ISSUE4.0
Serving the Telephone Industry Since 1930
519 W South Park Street
Okeechobee, FL 34972
Voice: 863-357-0798
Fax: 863-357-0006
Advertisement
Table of Contents
Related Manuals for CEECO SSW-521-D
Summary of Contents for CEECO SSW-521-D
- Page 1 SSW-521-D-SPK1.07UNVLr1-ADA-ISSUE4.0 SERVICE MANUAL MODEL SSW-521-D (FORMERLY SSW-521-DS) STAINLESS STEEL HANDS FREE WALL TELEPHONE WITH OPTIONAL ADA FEATURE EQUIPPED WITH SPK1.07UNVLr1 FIRMWARE Serving the Telephone Industry Since 1930 Communication Equipment 519 W South Park Street & Engineering Company Okeechobee, FL 34972...
-
Page 2: Important Information
ISSUE 4.0 IMPORTANT INFORMATION CUSTOMER Please fill in before you continue. The following information is necessary when calling CEECO for assistance. MODEL NUMBER MODEL SSW-521-D STAINLESS STEEL HANDS FREE WALL TELEPHONE EQUIPPED WITH SPK1.07UNVLr1 FIRMWARE. SERIAL NUMBER DATE MANUFACTURED LOCATION INSTALLED For us to better serve you, please have this information available when calling for technical support. -
Page 3: Table Of Contents
RECOMMENDED TOOLS AND TEST EQUIPMENT ........8 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS ..... 9 TESTING....................... 11 SPECIFICATIONS....................12 PARTS LIST ......................13 10.0 REPAIR AND RETURN INFORMATION............14 11.0 WARRANTY POLICY ..................15 12.0 DIAGRAM......................16 CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 4: Introduction
GENERAL The CEECO Model SSW-521-D Hands free telephone is a sturdy, vandal resistant, Stainless Steel Speakerphone, with optional ADA feature (RED/GREEN LED). Instead of a hookswitch and handset, the telephone is equipped with a Press to start/Press to stop Emergency Auto Dial button. -
Page 5: Programming
Enter #00, followed by a series of ten (10) digits as selected from the following page. Location “00” is the telephone options location. By entering a selected number of 0-9 into each of the ten digit locations, the phone is customized for the particular installation CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 6: Programming Continued
DIGIT 5 .. ALWAYS 0 DIGIT 6 .. ACTIVATE ADA FEATURE DIGIT 7 .. ALWAYS 0 DIGIT 8 .. DIAL THE PBX ACCESS NUMBER FIRST DIGIT 9 .. ALWAYS 0 DIGIT 10..250 ms wink detect. CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 7: Programming Continued
Return the two plastic mini-jumpers to the “off” or outermost position, as depicted on the last page of this manual. Disconnect the programming keypad and secure it safely somewhere for future use. The phone is now ready for installation/use. CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 8: Operation
LED provides a visual indication of the call progress. In order for the ADA LED to function, it must be activated by selecting “9” in section 3.6 under Digit 6. NOTE: CEECO cannot assume responsibility for the called party’s response. RECOMMENDED TOOLS AND TEST EQUIPMENT Volt/Ohm Meter 5/16"... -
Page 9: Installation Notes And Assembly Instructions
Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. CEECO Communication Equipment & Engineering Company PROPRIETARY... - Page 10 ISSUE 4.0 TELEPHONE LINE WIRING DIAGRAM TERMINATE TIP & RING HERE CEECO Communication Equipment & Engineering Company PROPRIETARY...
-
Page 11: Testing
Remember: The ADA feature must be activated during the programming of the phone. Action: Finish the conversation. Press the “Emergency” button again to hang up. The called party hangs up. Reaction: LED goes out. The call is terminated. CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 12: Specifications
PROGRAMMING : Via DTMF keypad. DIMENSIONS : 5"W X 10"H X 3 1/2"D MOUNTING : Vertical surface mount MEMORY RETENTION : Non-volatile memory retention WEIGHT : Approximately 6 Pounds TYPE JACK : RJ11C CEECO Communication Equipment & Engineering Company PROPRIETARY... -
Page 13: Parts List
QUANTITY PART NUMBER DESCRIPTION 301-018 MODULAR LINE CORD 301-054 MODULAR CONNECTOR (RJ11C) 521-200 SERVICE MANUAL 700-008 KEYPAD CABLE 660-000 CEECO SPK BOARD 705-110 CONNECTORIZED KEYPAD 6020-B MOMENTARY PANEL SWITCH 14123 SPEAKER 12017 RINGER STAINLESS STEEL COVER 321-015 STAINLESS STEEL BACKPLATE 9023 1/4-20 X 3/4"... -
Page 14: Repair And Return Information
10.3 NON-WARRANTY REPAIR CEECO will repair equipment out of warranty for a set charge plus parts. The customer must pay the shipping costs for both directions. 10.4 RETURN FOR CREDIT Material may be returned for credit only with prior approval. Material authorized for return is subject to a 20% restocking charge based on the manufacturer’s list price. -
Page 15: Warranty Policy
PRINTED CIRCUIT BOARDS Printed circuit boards should not be field repaired. If a unit is found to be faulty, replace it with another unit and return the faulty unit to CEECO for repair. Modifications by anyone other than CEECO will void the warranty. -
Page 16: Diagram
ON position BEFORE going off-hook. When programming is completed, move the mini jumpers to the OFF position. NOTE: Do not leave the mini jumpers in the ON position; this will decrease battery life. CEECO Communication Equipment & Engineering Company PROPRIETARY...
Need help?
Do you have a question about the SSW-521-D and is the answer not in the manual?
Questions and answers