Hayward PowerFlo Matrix Owner's Manual
  1. Manuals
  2. Brands
  3. Hayward Manuals
  4. Water Pump
  5. PowerFlo Matrix
  6. Owner's manual

Hayward PowerFlo Matrix Owner's Manual

Hide thumbs Also See for PowerFlo Matrix:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
PowerFlo Matrix
The Hayward PowerFlo Matrix Pump Series is specifically engineered for the demanding requirements of
today's above-ground swimming pools. The advanced design reduces maintenance requirements while
Basic safety precautions should always be followed, including the following: Failure to follow instructions
can cause severe injury and/or death.
This is the safety-alert symbol. When you see this symbol on your equipment or in this manual, look for
one of the following signal words and be alert to the potential for personal injury.
WARNING warns about hazards that could cause serious personal injury, death or major property
damage and if ignored presents a potential hazard.
CAUTION warns about hazards that will or can cause minor or moderate personal injury and/or property
damage and if ignored presents a potential hazard. It can also make consumers aware of actions that are
unpredictable and unsafe.
The NOTICE label indicates special instructions that are important but not related to hazards.
Owner's Manual
providing superior performance.

IMPORTANT SAFETY INSTRUCTIONS

Hayward Pool Products
620 Division Street, Elizabeth, NJ 07207
Phone: (908) 355-7995
www.hayward.com
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Pump
®
Contents
Warnings....................................2
Introduction...............................4
Seal Replacement......................8
Troubleshooting ........................9
Replacement Parts....................11
ISSP1591 Rev H
1

Advertisement

Table of Contents
loading

Related Manuals for Hayward PowerFlo Matrix

Summary of Contents for Hayward PowerFlo Matrix

  • Page 1: Table Of Contents

    Seal Replacement………….………8 Troubleshooting .………….…….…9 Replacement Parts………..………11 Warrantee & Registration ………12 The Hayward PowerFlo Matrix Pump Series is specifically engineered for the demanding requirements of today’s above-ground swimming pools. The advanced design reduces maintenance requirements while providing superior performance. IMPORTANT SAFETY INSTRUCTIONS Basic safety precautions should always be followed, including the following: Failure to follow instructions can cause severe injury and/or death.

  • Page 2: Warnings

    Use on nly a low pressur re (below 5 PSI) , high volume b blower when ai r purging the pu ump, filter, or p piping. USE ONLY Y HAYWARD GE ENUINE REPLA ACEMENT PAR...

  • Page 3: Save These Instructions

    Unawareness of impending danger. Failure to perceive heat. Failure to recognize the need to leave the spa. Physical inability to exit the spa. Fetal damage in pregnant women. Unconsciousness resulting in danger of drowning. SAVE THESE INSTRUCTIONS USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 4: Introduction

    Product Specifications Dimensions General Information Introduction This manual contains information for the proper installation and operation of the Hayward PowerFlo Matrix ® pump. WARNING Read and follow all instructions in this owner’s manual and on the equipment. Failure to follow instructions can cause severe injury and/or death.
  • Page 5 Pump Mounting Fasten pump to base or pad with screws or bolts to reduce vibration and stress on pipe or hose joints. Hayward recommends a minimum clearance around the pad of 18” to allow adequate access for servicing pump and piping.

  • Page 6: Troubleshooting

    New Installation – Start-Up & Operation Selecting Pump’s Discharge Position (4 Steps) Your Hayward Power-Flo Matrix™ pump can be easily positioned for horizontal or vertical water discharge. Step 1: Remove ALL plumbing attached to pump. Remove pump from base (if applicable).

  • Page 7: Storage/Winterization

    NOT cover or wrap pump with plastic film or bags. Start-Up for Winterized Equipment Securely mount pump to base. 2. Install all intake and output fittings and piping. 3. Refill pool to proper water level. 4. Prime pump according to instructions. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 8: Seal Replacement

    Shaft Seal Change Instructions CAUTION -Only qualified personnel should attempt rotary seal replacement. Contact your local authorized Hayward Dealer or service center if you have any questions. WARNING Read and follow all instructions . Failure to follow instructions can cause severe injury and/or death.

  • Page 9: Troubleshooting

    3. Mechanical binding and electrical overload. NOTE: Your Hayward pump motor is equipped with an “automatic thermal overload protector.” The motor will automatically shut off if power supply drops before heat damage can build up causing windings to burn out. The “thermal overload protector”...
  • Page 10 Clean strainer basket regularly. Do NOT strike basket to clean. Inspect strainer cover gasket regularly and replace as necessary.  Hayward pumps have self-lubricating motor bearings and shaft seals. No lubrication is necessary.  Keep motor clean. Insure air vents are free from obstruction.

  • Page 11: Replacement Parts

    2 HP Single Speed Motor with Switch, Flex-48 SPX1524Z1ESC 2 ½ HP Single Speed Motor with Switch, Flex-48 SPX1510Z24XE 1 HP Two Speed Motor with Switch, Flex48 SPX1515Z2WS 1 ½ HP Two Speed Motor with Switch, Flex-48 SP1500UNPAK2 Union Connector Assembly USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...

  • Page 12: Warrantee & Registration

    Li mited Wa rranty ® To origin nal purchasers o f this equipment, , Hayward Pool P roducts warrants its products to b be free from defec cts in materials a and workmanship p for a period of ▲Retain this W...

Table of Contents