Roland XP-60 Owner's Manual page 81

L in
Left Tap
Triple Tap Delay
Feedback
Right Tap
R in
Delay Center (Delay time center)
Adjust the time delay from the direct sound until when the
center delay sound is heard. This parameter can be set as a
note-value of a specified tempo. In this case, specify the
value of the desired note.
Delay Left (Delay time left)
Adjust the time delay from the direct sound until when the
left delay sound is heard. This parameter can be set as a
note-value of a specified tempo. In this case, specify the
value of the desired note.
Delay Right (Delay time right)
Adjust the time delay from the direct sound until when the
right delay sound is heard. This parameter can be set as a
note-value of a specified tempo. In this case, specify the
value of the desired note.
...........................................................................................................
As the specified tempo, you may use either the Patch
Tempo parameter (PATCH/Common/Common General),
Performance Tempo (PERFORM/Common/Common), or
the tempo clock of the XP-80's sequencer.
If you want to use a fixed tempo in Patch mode (Patch
Tempo parameter setting), set the Clock Source parameter
(PATCH/Common/Common General) to PATCH and set
the desired tempo.
If you want to use the sequencer's tempo clock in Patch
mode, set the Clock Source parameter (PATCH/Common/
Common General) to SEQUENCER.
If you want to use a fixed tempo in Performance mode
(Perform Tempo parameter setting), set the Clock Source
parameter (PERFORM/Common/Common) to PERFORM
and set the desired tempo.
If you want to use the sequencer's tempo clock in
Performance mode, set the Clock Source parameter (PER-
FORM/Common/Common) to SEQUENCER.
...........................................................................................................
Feedback (Feedback level) #
Adjust the proportion (%) of the processed sound that is fed
back into the effect. Negative (-) settings will invert the phase.
Center Level
Adjust the volume of center delay sound.
Left Level
Adjust the volume of left delay sound.
Right Level
Adjust the volume of right delay sound.
Balance D
2-Band
EQ
Balance W
Center Tap
Balance W
2-Band
EQ
Balance D
Chapter 3. Creating your own sounds
HF Damp
L out
Adjust the frequency above which sound fed back to the
effect will be cut. If you do not want to cut the high frequen-
cies of the feedback, set this parameter to BYPASS.
Low Gain
Adjust the gain of the low frequency range.
R out
High Gain
Adjust the gain of the high frequency range.
Balance (Effect balance) #
Adjust the volume balance between the direct sound and the
processed sound.
Level (Output level)
Adjust the output level.
20: QUADRUPLE-TAP-DELAY
The Quadruple Tap Delay has four delays. Each of the Delay
Time parameters can be specified as a note length of the
selected tempo.
L in
Feedback
R in
The stereo location of each delay sound is as follows.
Delay 1 (Delay time 1)
Delay 2 (Delay time 2)
Delay 3 (Delay time 3)
Delay 4 (Delay time 4)
Adjust the time delay from the direct sound until when each
delay sound is heard. These parameters can be set as a note-
value of a specified tempo. In this case, specify the value of
the desired note.
...........................................................................................................
As the specified tempo, you may use either the Patch
Tempo parameter (PATCH/Common/Common General),
Performance Tempo (PERFORM/Common/Common), or
the tempo clock of the XP-80's sequencer.
If you want to use a fixed tempo in Patch mode (Patch
Tempo parameter setting), set the Clock Source parameter
(PATCH/Common/Common General) to PATCH and set
the desired tempo.
If you want to use the sequencer's tempo clock in Patch
mode, set the Clock Source parameter (PATCH/Common/
Common General) to SEQUENCER.
Balance D
Delay 1
Delay 2
Quadruple Tap Delay
Delay 3
Delay 4
Balance D
2 3
1 4
R
L
L out
Balance W
Balance W
R out
81