Roland XP-60 Owner's Manual page 163

Source
PR-A
ALL
PR-B
USER
PR-A
PERFORM
PR-B
DISK
USER
PR-A
PR-B
PR-C
GM
PATCH
XP-A
XP-B
XP-C
XP-D
DISK
USER
PR-A
PR-B
PR-C
GM
RHYTHM
XP-A
XP-B
XP-C
XP-D
DISK
SYSTEM Disk
1: All Patches, Performances and Rhythm Sets in PR-A
group
2: All Patches, Performances and Rhythm Sets in PR-B group
3: The Performance of the specified number in USER group
4: The Performance of the specified number in PR-A group
5: The Performance of the specified number in PR-B group
6: Performances recorded in a data file. To transmit data of a
specific Performance only, specify that Performance number.
7: The Patch of the specified number in USER group
8: The Patch of the specified number in PR-A group
9: The Patch of the specified number in PR-B group
10: The Patch of the specified number in PR-C group
11: The Patch of the specified number in GM group
12: The Patch of the specified number in XP-A group
13: The Patch of the specified number in XP-B group
14: The Patch of the specified number in XP-C group
15: The Patch of the specified number in XP-D group
16: Patches recorded in a data file. To transmit data of a spe-
cific Patch only, specify that Patch number.
17: The Rhythm Set of the specified number in USER group
18: The Rhythm Set of the specified number in PR-A group
19: The Rhythm Set of the specified number in PR-B group
20: The Rhythm Set of the specified number in PR-C group
21: The Rhythm Set of the specified number in GM group
01-32
01-32
01-32
01: *.SVD 01-32
001-128
001-128
001-128
001-128
001-128
001-
001-
001-
001-
01: *.SVD 001-128
001-002
001-002
001-002
001-002
001-002
001-
001-
001-
001-
01: *.SVD 001-002
01: *.SVD
Chapter 8. XP-80 memory settings (Utility mode)
22: The Rhythm Set of the specified number in XP-A group
23: The Rhythm Set of the specified number in XP-B group
1 24: The Rhythm Set of the specified number in XP-C group
25: The Rhythm Set of the specified number in XP-D group
2
26: Rhythm Sets recorded in a data file. To transmit data of a
3
specific Rhythm Set only, specify that Rhythm Set number.
4
27: System recorded in a data file.
5
It is not possible to select 12–15 or 22–25 when an
6
Expansion Board is not installed into the specified slot
(p.45).
7
When 6, 16, 26 or 27 is selected, you can view the list of
8
data files stored on disk by pressing [F5] (List). To
9
select a data file from the list, move the cursor to the
10
desired data file and press [F6] (Select) or [ENTER].
11
12
13
14
15
16
17
18
Destination
19
"to User" means that data will be transmitted to user memo-
ry.
20
21
You can also specify the destination number at this point.
22
If 1, 2 or 27 is selected for the Source parameter, it is
23
not possible to specify the destination number.
24
<Procedure>
25
Make sure that the Utility Menu (UTILITY) is up.
26
Press [F6] (Menu) to select Menu 1, then press [F4]
(Xfer) to select Data Transfer.
27
You can also select Data Transfer by moving the cursor to "4
Data Transfer" and pressing [ENTER] on the Utility Menu
display (UTILITY), or pressing the numeric key [4], then
[ENTER].
Press [F3] (to User) to call up the Data Transfer to User
display (UTILITY/Xfer).
Move the cursor to "Source" and specify the data you
want to transmit.
Move the cursor to "Destination" and specify the
transmission destination number.
Press [F6] (Execute) to transmit the data.
While data is being transmitted, the display will read
"Transmitting..."
To interrupt transmission of data from disk, press
[EXIT].
[UTILITY] [4] [ENTER]
Volume label
163