Index - Watlow 97 series User Manual

Index

A
Address 6.14
Alarm 2 Low 6.5
Alarm 2 High 6.5
Alarm 2 Status 6.4
Alarm 2 Type 6.10
Alarm 3 Low 6.5
Alarm 3 High 6.6
Alarm 3 Status 6.4
Alarm 3 Type 6.11
Alarm 4 Low 6.6
Alarm 4 High 6.6
Alarm 4 Status 6.4
Alarm 4 Type 6.12
Alarm 5.8-5.11
hysteresis 5.8
latching 5.9
process 5.9
set points 5.8
silencing 5.10
Alarm Active Sides 2 6.10
Alarm Active Sides 3 6.11
Alarm Active Sides 4 6.12
Alarm Annunciation 2 6.10
Alarm Annunciation 3 6.12
Alarm Annunciation 4 6.13
Alarm Hysteresis 2 6.10
Alarm Hysteresis 3 6.11
Alarm Hysteresis 4 6.12
Alarm Logic 2 6.10
Alarm Logic 3 6.11
Alarm Logic 4 6.13
Alarm Menu 6.5-6.6
Ambient A-D Counts 6.19
Ambient Temperature 6.19
Analog Output 4 6.13
Analog Output High 6.13
Analog Output Low 6.13
Analog Output Offset 6.13
B
Baud Rate 6.13
C
C or F 6.16
Calibrating A.11-A.13
Process Output A.13
RTD Input A.12
Thermocouple Input A.12
Wa t lo w Ser i es 9 7
Calibration Menu Lock 6.17
Calibration Offset 5.3, 6.5
Channel 1 A-D Counts 6.19
Channel 2 A-D Counts 6.19
configure the controller 4.6
communications 5.11
and retransmit option 3.10
converting between EIA-232 and EIA-
435 3.11
customer feedback inside front cover
cyclical redundancy checksum (CRC)
algorithm A.9
D
Date of Manufacture 6.17
Decimal 1 6.8
Default Settings 6.20
Diagnostics Menu 6.17-6.19
Digital event, wiring 3.6
Display Menu 6.14-6.16
E
EIA Conversion 3.11
Errors, troubleshooting A.2-A.3
Event Condition 6.9
Event Function 6.9
Event Input 5.6
Event Input Status 6.4
exception responses A.8
F
Factory Page 4.5
Factory Page menus 6.17-6.21
filter time constant 5.4
G
gap dimensions 2.2
Global Menu 6.16
H
High Limit Set Point 6.5
High Resolution 6.19
Home Page 4.4, 6.3
I J
Input 1 6.7
Input 2 6.9
Input 2 Hardware Enabled 6.18
Input 1 Menu 6.7-6.8
Input 2 Menu 6.9
Input Calibration Menu 6.19-6.21,
A.12
Input Error Latching 6.16
Inputs and outputs 1.1
Input Software Filter 1 6.8
Input-to-output isolation 3.2
Input wiring
digital event 3.6
RTD 3.6
thermocouple 3.6
Installation 2.1-2.2
Installation sensor 3.3
Isolation blocks 3.2
K
Keys and displays 4.2
L
Latching 2 6.10
Latching 3 6.11
Latching 4 6.12
Lead Resistance Calibration 6.20
Limit Active Sides 6.9
Limit Hysteresis 6.9
Limit Menu 6.5
Limit Status 6.4
Line Frequency 6.19
Lockout Menu 6.17
Loop back command A.7
Lower Display 6.14
Lower Display User Limit Message
6.16
Lower Display User Safe Message
6.15
Low Limit Set Point 6.5
M
Modbus Remote Terminal Unit
(RTU) A.4
Model Number 6.17
Monitor Menu 6.4
Multiple registers command
read A.5
write A.6
N
Navigation
map 4.4-4.5
and Software 4.1-4.7
tasks for users 4.6-4.7
A p p e n d i x A.2 1