Table of Contents
Advertisement
A
Alarms, 49
Alarm Codes, 50
Almost Ready to Run, 22
Analog Retransmit, 52
B
Before You Begin (Programming), 18
Bad Sensor, 74
C
Change Data Flow Diagram, Fig. 20,42
CHG DATA Overview, Fig. 8,14
Change Parameter Flow Diagram, Fig. 21,46
CHG PARA Overview, Fig. 9,15
Cycle Time, 48
D
Data Comm. Commands and Syntax, 61
Data Comm. Error Codes, 73
Dimensions, Unit and Panel Cutout, Fig. 13, 33
DIP Switches, 6, 18,40
Clear Memory, 18
How to Set, 6
Position and Function, Table 1, 6
Display and Keys, 10
Dry Bulb Installation, RTD, 26
E
Electrical Connections and Wiring, 34-38
Enter Real Time, 18
Entering Data, 19
Error Codes, 73
Event Input, 36.51
Event Outputs, 51
F
Front Panel Components, Fig. 6,
Flow Diagrams, Fig. 20,42
G
RTD General Parameter Chart, Chart 4,55
T/C General Parameter Chart 5,56
RTD Guarded Access Chart, Chart 2.53
T/C Guarded Access Chart, Chart 3,54
H
Halt Conditions, 22
Helpful Hints: 22-24
Ramping Conditions, 23
Wait-Step, 23
Jump Loop Step, 24
Recycle, 24
I
Installation Procedure, 34
Interface RS-422/423-Pins, Fig. 19,38
Introduction, Read Me First, 4
J
Jumper, Input Selection, 35
Jumper, RS423/422 Selection, 38
Jump Loop Step (JL), 24
M, N
Model # Information, 82
Modes, Operating Overview, Fig. 5,9
Monitoring the Action, 22
MNTR DATA Overview, Fig. 7,13
27-28
Noise, reduction of,
Non-Ramping Set
Point, 9, 13
Index,
Appendix
0
opening the
Overview, Input & Output Fig.
Overview, Operating Modes, Fig. 5, 9
Overview, MNTR DATA, Fg. 7,13
Overview, CHG DATA, Fig. 8.14
Overview, CHG PARA, Fig. 9.15
P
Packing List, 5
Pre-installation Information, 32
Programming, 16-2540-48
Programming Chart, Chart 6,57
Proportional Band, 47
Q
Quick Reference, 90
Quick Wire, 7
Quick Wire AC Power Connections, Fig. 3, 7
Quick Wire Simulated Sensor Wiring, Fig. 4, 8
R
Ramping Conditions, 23, 43
Rate, 48
Rate Band, 48
Recycle Option, 24.41
Remote Hold, 36,51
Reset, 47
Returning Merchandise, 83
RTD Installation Guidelines, 26
Run and Halt a Program, 60
S
Sample Program, 16
Programming Step 1, 19
Programming Step 2.20
10
Programming Steps 3 through 6,21
Programming Step 7, Jump Loop Step, 21
Programming Step 8, 21
Program Chart, Chart 1.17
Program Event Outputs, Table 2, 17
Program Steps, Table 3,2l
Setting Event Outputs, 17
Shipping Claims, 84
Software, Overview, 12
Specifications,
Start Your Program!, 22
Syntax, 64-72
T
Temp-RH Selection, 26
T/C Installation Guidelines, 27
Temp-Temp Selection, 26
Tuning, 59
U
w
V
Wait Step, 23,45
Warranty Information, 83
Watlow RTD's, 26
Watlow Winona, Inc., 84
Wet Bulb Installation, RTD, 26
Wiring, Control, 36
Wiring Data Comm., 39
Wiring, Disable Ch-2.38
Wiring, Input, 36,37
Wiring, Output, 36,37
Wiring, Power, 38
Wiring Practices for
1500, 5, 32
1.4
80
Preventing Noise, 27-28
WATLOW Series 1500 User's Manual
89
Advertisement
Table of Contents
