Table of Contents
Advertisement
Quick Links
AT-6 TEXAN
0.91
1.10
-
R
equire : 6-channel
Wing Span
Wing Area
Flying Weight
Fuselage Length
Warning! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this
kind of engine powered precision model. Operating this model without prior preparation may
cause injuries. Remember, safety is the most important thing. Always keep this instruction
manual at hand for quick reference.
The World Models
Manufacturing Co
www.theworldmodels.com
A212PO25901108
cu in displacement 4-stroke
.
s
and 1 low profile retract servo
Specifications
* Specifications are subject to change without notice.*
., Ltd .
.
radio w/ 6 standard
72 in / 1830 mm
777 sq in / 50.1 sq dm
8.4 lbs / 3800 g
51.5 in / 1310 mm
INSTRUCTION MANUAL
ARF
servos
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY(ARF) SERIES
MADE IN CHINA
Advertisement
Table of Contents
Related Manuals for The World Models Manufacturing AT-6 TEXAN
Summary of Contents for The World Models Manufacturing AT-6 TEXAN
-
Page 1: Specifications
INSTRUCTION MANUAL AT-6 TEXAN 0.91 1.10 cu in displacement 4-stroke equire : 6-channel radio w/ 6 standard servos and 1 low profile retract servo Specifications Wing Span 72 in / 1830 mm Wing Area 777 sq in / 50.1 sq dm Flying Weight 8.4 lbs / 3800 g... -
Page 2: Before You Begin
AT-6 TEXAN I N D E X BEFORE YOU BEGIN P. 1 PARTS LIST P. 2 ASSEMBLY P. 3 -12 SAFETY PRECAUTIONS P.13 BEFORE YOU BEGIN Read through the manual before you begin, so you will have an overall idea of what to do. -
Page 3: Parts List
Parts List 1. MAIN WING -- 1 set 11. FUEL TANK 380cc PL1111380 -- 1 set CABLE TIE (For Fuel Tank) 1.5x5x400mm -- 1 pc. DOUBLE-SIDED TAPE 40x100mm -- 1 pc. 2. MAIN LANDING GEAR COVER -- 1 pair SCREW PM2x8mm -- 8 pcs 12. - Page 4 Main Wing Pre-glued Bottom View Aileron servo lead Peel off shaded portion covering film. Pre-glued Bottom View PM2x8mm Screw M2 Nut d2xD5mm Washer PM2x8mm M2 NUT Completed d2xD5mm Washer Bottom View A212PO25901108...
- Page 5 Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. PB2x25mm Screw TWM PL8210010 CLEVIS WRENCH PWA2x8mm Screw Fuel Tube Straper 6x5mm PWA2x8mm Ø PB2x25mm 1.5mm Clevis Tri-horn Fuel Tube M3x14mm(L) Ø6x5mm Pushrod Ø1.8x85mm...
- Page 6 Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. PB2x15mm Screw Select the servo horn that will Lead to Aileron servo give 26mm travel when rotates through 180 . R-side L-side Wheels down Position...
- Page 7 pre-glued C=C' completed PA3x12mm Screw 2.6mm Collar 5.8x18x43mm 3mm Set Screw 1.5mm 2.5mm PA3x12mm Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. TWM PL8210010 CLEVIS WRENCH PB2x22mm Screw PB2x22mm Clevis Fuel Tube...
-
Page 8: Double-Sided Tape
Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole marks at side of control surfaces. PM2.5x35mm Screw TWM PL8210010 CLEVIS WRENCH Tri-horn M3x22mm(L) Fuel Tube Ø6x5mm Clevis 2.5mm Rudder Pushrod PM2.5x35mm Ø1.8x835mm DOUBLE-SIDED TAPE 40x100mm CABLE TIE 1.5x5x400mm Wooden dowel Ø5.5x9mm... - Page 9 3 x 3mm Set Screw Included with the radio Set. Linkage Connector M2 Nut 2mm Washer M2 Nut Throttle Servo. Please refer to attached sheet for linkage connector installation. Installed Engine position M4x35mm Socket Head Screw Engine Mount KM3x20mm Screw Aluminum Plate 137mm 5.39in...
-
Page 10: Bottom View
Install and arrange the servos as shown in the diagram. wire Throttle Push Ø1.2x400mm Plastic tube Rudder Servo d2xD3x200mm Throttle Servo Straper Fuel Tube Receiver Ø6 x 5mm Elevator Servo Battery Sponge Pushrod Ø1 8x75mm Elevator Pushrod Ø1.8x75mm M2 Nut Pushrod Connector Pushrod Ø1 8x730mm... - Page 11 First insert the grommet to the canopy then apply screw. PWA2.3x8mm Screw Pilot d1.5xD6.5mm Silicon Grommet PWA2.3x12mm 1m m Silicon Grommet d1.5xD6.5mm Please refer to the attached sheet for usage of the transparent 3D template. PWA2.6x12mm Screw KA2.3x8mm Screw Carb Intake Spinner Nut Oil Cooler Intake Completed...
- Page 12 Adjust the wing and fuselage configuration as shown in the diagrams. A = A ' B = B ' C = C ' P.11 A212PO25901108...
- Page 13 Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference. Elevator 25mm 25mm Rudder 45mm 45mm Flaps (near fuselage ) 30mm Ailerons ( away from fuselage ) 16mm 16mm The ideal C.
-
Page 14: Important Safety Precautions
Pre - flight adjustment must be done before flying, it is very dangerous to fly a badly pre - adjusted aircraft. AT-6 TEXAN is specially designed to be powered by 0.91-1.10 4-stroke glow engine, using a more powerful engine does not mean better performance. In fact, over powered engine may cause severe damage and injuries. - Page 15 Usage of the transparent 3D template This transparent 3D template is used for position guidance of the actual cutting of the pre-painted cowling. Simply cut the transparent 3D template to fit your engine and exhaust pipe, then slide onto the actual cowling and use as template to mark the openings required for final cutting.
- Page 16 www .thew orldm odels .com A212PO25901108...