The World Models Manufacturing Zero Fighter EP Instruction Manual
  1. Manuals
  2. Brands
  3. The World Models Manufacturing Manuals
  4. Toy
  5. Zero Fighter EP
  6. Instruction manual

The World Models Manufacturing Zero Fighter EP Instruction Manual

5-channel radio w/ 5 micro servos outrunner motor km0283010 w/ propeller adaptor hw2340100 20a brushless esc, 3 cells 11.1v 2100 mah li - po battery & charger
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ZERO FIGHTER EP
Requires : 5-channel radio w/ 5 micro servos,
Outrunner Motor KM0283010
w/ Propeller Adaptor HW2340100,
20A brushless ESC, 3 cells 11.1V
2100 mAh Li - Po battery & charger.
Wing Span
Wing Area
Flying Weight
Fuselage Length
* Specifications are subject to change without notice.*
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
THE WORLD MODELS
MANUFACTURING CO., LTD.
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY(ARF)SERIES
MADE IN CHINA
www.theworldmodels.com
S p ecifica tio n s
39.5 in / 1000 mm
264 sq in / 17 sq dm
27 oz / 760 g
32 in / 820 mm
INSTRUCTION MANUAL

Advertisement

Table of Contents
loading

Related Manuals for The World Models Manufacturing Zero Fighter EP

Summary of Contents for The World Models Manufacturing Zero Fighter EP

  • Page 1 INSTRUCTION MANUAL ZERO FIGHTER EP Requires : 5-channel radio w/ 5 micro servos, Outrunner Motor KM0283010 w/ Propeller Adaptor HW2340100, 20A brushless ESC, 3 cells 11.1V 2100 mAh Li - Po battery & charger. S p ecifica tio n s Wing Span 39.5 in / 1000 mm...

  • Page 2: Before You Begin

    ZERO FIGHTER EP INDEX BEFORE YOU BEGIN PARTS LIST ASSEMBLY P.3-P.9 SAFETY PRECAUTIONS BEFORE YOU BEGIN Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.

  • Page 3: Parts List

    Parts List 1. MAIN WING -- 1 pc. 9. SCREW PM3x6mm -- 4 pcs WASHER d3xD7mm -- 4 pcs 2. RETRACTABLE LANDING GEAR -- 1 pair FOLDING PROPELLER SET PL6314020 -- 1 set SCREW KA2.3x8mm -- 8 pcs SCREW PM2x12mm -- 2 pcs COLLAR Ø2.6mm w/ Set Screw -- 2 pcs COWLING -- 1 pc.

  • Page 4: Retractable Landing Gear

    Main Wing Apply instant type CA glue to both sides of each hinge. Aileron Servo Lead Bottom View Aileron Servo Lead Retractable Landing Gear Bottom View...

  • Page 5: Retract Servo

    Please refer to attached sheet for linkage connector installation. Retract Servo Linkage connector To R-Side To L-Side Wheels Down Position 16mm Travel 16mm Travel Wheels Up Position Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole Aileron Servo marks at under side of control surfaces.

  • Page 6: Rudder Pushrod

    Vertical Fin, Rudder & Tail Landing Gear PA2x8mm WHEEL Ø23mm PA2x8mm Screw Plastic Collar Bottom View 1.2mm C=C' Completed Apply instant type CA glue to both sides of each hinge. Ø1mm pilot holes for World Models horn are pre-drilled. Rudder Pushrod Please look for pin-hole marks at under side of control surfaces.

  • Page 7: Elevator Pushrod

    Elevator Pushrod Ø1mm pilot holes for World Models horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. PB2x8mm Screw Fuel Tube PB2x8mm d2xD4x4mm 55mm 12mm Pushrod Ø1.4x365mm Clevis Horn Bottom View Outrunner Motor / Cowling Optional Parts PWA2x8mm Screw Don't over-tighten the...

  • Page 8: Radio Equipment

    Radio equipment Battery Tie Elevator Pushrod Receiver Ø1.4x365mm Front Elevator Servo Sponge Battery Install and arrange the servo as shown in the diagram. Elevator Pushrod Ø1.4x52mm Straper Rudder Pushrod 20A Brushless ESC Fuel Tube Ø1.4x430mm d2xD4x4mm Double-Sided Tape Rudder Servo KA1.7x5mm J1(Pushrod Ø1.4x52mm) Elevator Servo...
  • Page 9 Canopy Lazyback Antenna Pilot PWA2x8mm Screw Lazyback Antenna PWA2x8mm 1.5mm Wing Setting Adjust the wing and fuselage configuration as shown in the diagrams. A=A' B=B' C=C' D=D'...

  • Page 10: Control Throws

    # First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary. # Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft. ZERO FIGHTER EP is specially designed to be powered by KM0283010 Outrunner Motor.
  • Page 11 LINKAGE CONNECTOR HW7111050 & HW7111060 Drill 2mm hole at servo horn. Insert linkage connector into servo horn. Make sure shoulder of screw is cleared from servo horn. Add washer to reduce play if necessary. Shoulder Tighten up the round nut against the shoulder.
  • Page 12 http://www.theworldmodels.com E216XM0806...

Table of Contents