Download Print this page

KRAUSE & BECKER 60600 Owner's Manual

Airless paint sprayer.
Hide thumbs

Advertisement

Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
RETURNS NOT ACCEPTED
& WARRANTY VOID
if Sprayer is not properly cleaned
immediately after every use.
Clean Sprayer immediately
to prevent permanent damage.
See "Cleaning" and "Long Term Storage" on pages 16-18.
Email our technical support at: productsupport@harborfreight.com
REV 16h
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2012 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
REV 16h
60600

Advertisement

   Related Manuals for KRAUSE & BECKER 60600

   Summary of Contents for KRAUSE & BECKER 60600

  • Page 1

    (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. REV 16h 60600 RETURNS NOT ACCEPTED & WARRANTY VOID if Sprayer is not properly cleaned immediately after every use.

  • Page 2

    It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SAVE THESE INSTRUCTIONS Page 2 For technical questions, please call 1-888-866-5797. ITEM 60600...

  • Page 3

    Interrupter (GFCI) protected supply. or binding of moving parts, breakage of parts Use of a GFCI reduces the risk of electric shock. and any other condition that may affect the ITEM 60600 For technical questions, please call 1-888-866-5797. Page 3...

  • Page 4

    22. Paint Sprayer’s housing may become hot during use. 8. Do not use Paint Sprayer to spray Do not touch housing until it has completely cooled. asbestos, metallic paints, glazes, Page 4 For technical questions, please call 1-888-866-5797. ITEM 60600...

  • Page 5

    Keep it out of reach of children. 29. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. ITEM 60600 For technical questions, please call 1-888-866-5797. Page 5...

  • Page 6: Extension Cords

    12.1 – 16.0 with all codes and ordinances. The plug and 16.1 – 20.0 outlet should look like those in the preceding illustration. (See 3-Prong Plug and Outlet.) Page 6 For technical questions, please call 1-888-866-5797. ITEM 60600...

  • Page 7

    150% of the rated amperes. Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes No Load Revolutions n 0 xxxx/min. per Minute (RPM) ITEM 60600 For technical questions, please call 1-888-866-5797. Page 7...

  • Page 8

    Pressure Control Knob Paint Hose Outlet Filter Prime/Spray Switch Red Inlet Release Button (underneath) Power Cord Spray Tip Hanging Hook Spray Gun Spray Tip Guard Trigger Guard Trigger Paint Hose Page 8 For technical questions, please call 1-888-866-5797. ITEM 60600...

  • Page 9

    Low Pressure Spraying, Priming/Cleaning, or Rolling. Align the Pressure Control Knob with indicator on the Sprayer Housing to set the function. Hi Spray Low Spray Prime/Clean Roll Low Pressure Spray Rolling High Pressure Spray Prime/Clean ITEM 60600 For technical questions, please call 1-888-866-5797. Page 9...

  • Page 10

    2. Attach Paint Hose to Paint Gun and tighten with two wrenches. 1. Attach Paint Hose to Paint Hose Outlet and tighten with wrench. 3. Turn Pressure Control Knob to Low Pressure Spray setting. Page 10 For technical questions, please call 1-888-866-5797. ITEM 60600...

  • Page 11

    Turn Power Switch off and unplug unit from outlet. 2. Switch Prime/Spray switch to Prime mode to safely release most pressure. 3. Point gun into paint pail and activate Sprayer Trigger to relieve an remaining pressure. ITEM 60600 For technical questions, please call 1-888-866-5797. Page 11...

  • Page 12

    IMPORTANT: If solvent will not flow through hoses, try pressing the red inlet release button underneath 3. Submerge Suction Tube in water or flushing solvent. the pump to loosen the inlet check ball. Page 12 For technical questions, please call 1-888-866-5797. ITEM 60600...

  • Page 13

    Priming Tube until paint discharges from Priming Tube. 11. Switch power off. Remove the Priming Tube from the waste bucket and clip to Suction Tube and submerge in paint pail. ITEM 60600 For technical questions, please call 1-888-866-5797. Page 13...

  • Page 14

    Overlap Strokes 3. Practice the Painting Techniques that follow on a scrap workpiece before painting your workpiece. Overlap strokes by half, always aim stroke at bottom edge of last stroke. Page 14 For technical questions, please call 1-888-866-5797. ITEM 60600...

  • Page 15

    5. Spray into waste bucket until clog clears. 6. Release Trigger. 2. Adjust nozzle to eject setting. 3. Turn Spray/Prime Switch to Spray mode. 7. Adjust nozzle to Spray mode. ITEM 60600 For technical questions, please call 1-888-866-5797. Page 15...

  • Page 16

    7. After fluid in Priming Tube is clear, switch Power to Off. 3. Drain paint from Tubes. 8. Turn to Spray mode and switch power to on. 4. Separate tubes. Page 16 For technical questions, please call 1-888-866-5797. ITEM 60600...

  • Page 17

    11. Turn to Prime mode. 15. Remove filter. 12. Continue to flush until clear. 16. Clean all parts in warm, soapy water or flushing fluid with a bristled brush. ITEM 60600 For technical questions, please call 1-888-866-5797. Page 17...

  • Page 18

    10. Wipe the sprayer with a clean cloth. Store in a clean dry location out of reach of children. 5. Turn Pressure Control Knob to Low/Spray. Hi Spray Low Spray Prime/Clean Roll Page 18 For technical questions, please call 1-888-866-5797. ITEM 60600...

  • Page 19

    2. Sand wood to a sufficiently fine grit before painting. 3. Raised grain. 3. Wipe wood surface with thinner to raise grain, then sand with fine grit to knock off “hairs”. ITEM 60600 For technical questions, please call 1-888-866-5797. Page 19...

  • Page 20

    Tapping Screw Clip Power Cord Fixer Inlet Pipe Lock Ring Hex Bolt (M4x20) Filtrate Seat Assembly Wire label Bolt (M5x20) Power Cord Pole Stopper Locking Ring Small Gear Washer Screw (M4x14) Page 20 For technical questions, please call 1-888-866-5797. ITEM 60600...

  • Page 21

    Assembly Diagram ITEM 60600 For technical questions, please call 1-888-866-5797. Page 21...

  • Page 22

    LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Page 22 For technical questions, please call 1-888-866-5797. ITEM 60600...

  • Page 23

    Specifications Electrical Input 120VAC / 60Hz / 7A Motor 5/8 HP Max. Working Pressure 3000 PSI Outlet 1/4″-NPS M Paint Hose 25′ Long ITEM 60600 For technical questions, please call 1-888-866-5797. Page 23...

  • Page 24

    3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797 www.harborfreight.com...

Comments to this Manuals

Symbols: 0
Latest comments:
  • HARRIS TRAN May 04, 2018 09:26:
    Please let me know what country is this product made from?
  • clodio zolozabal martinez Feb 19, 2018 09:40:
    donde solicito partes de equipo gracias
  • Frank Jan 11, 2018 11:09:
    Where the wire goes bl and white and green to power switch
  • N. Rasmussen Dec 03, 2017 12:33:
    A very small white bead fell out of somewhere - I believe nozzle and I would like to know where it goes. Please tell me where to put this back,