Table of Contents
Advertisement
Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
NOTICE
CLEAN IMMEDIATELY
Clean the Spray Gun IMMEDIATELY
after EVERY use, in between coats,
and when it will be idle for
more than 5 minutes.
Delayed or inadequate cleaning will
permanently clog the Spray Gun.
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2014 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
REV 15c
ITEM 60446
Advertisement
Table of Contents
Related Manuals for KRAUSE & BECKER 60446
Summary of Contents for KRAUSE & BECKER 60446
- Page 1 (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. REV 15c ITEM 60446 NOTICE CLEAN IMMEDIATELY...
-
Page 2: Table Of Contents
WARNING – When using tools, basic precautions should always be followed, including the following: Page 2 For technical questions, please call 1-888-866-5797. Item 60446... -
Page 3: Work Area
Always wear eye protection. Loose clothes, jewelry, or long hair Wear ANSI-approved increases the risk of injury to persons as safety goggles. a result of being caught in moving parts. Item 60446 For technical questions, please call 1-888-866-5797. Page 3... -
Page 4: Tool Use And Care
9. Attach all accessories properly potential chemical reactions. to the tool before plugging in the tool. A loose accessory may detach 5. Industrial applications must or break during operation. follow OSHA requirements. Page 4 For technical questions, please call 1-888-866-5797. Item 60446... - Page 5 It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SAVE THESE INSTRUCTIONS. Item 60446 For technical questions, please call 1-888-866-5797. Page 5...
-
Page 6: Extension Cords
5. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Table A.) Page 6 For technical questions, please call 1-888-866-5797. Item 60446... -
Page 7: Specifications
Viscosity Cup with hanger/ Four Nozzles including: Container Capacity 24 fl. oz. 2 - .032″ (0.8mm), Flow Rate 5 GPH 1 - .021″ (0.5mm), 1 - Extension .021″ (0.5mm) HOUSEHOLD USE ONLY. 4005149 Item 60446 For technical questions, please call 1-888-866-5797. Page 7... - Page 8 Delayed or inadequate cleaning will permanently clog the Spray Gun. Latex paint hardens quickly and permanently inside Spray Gun. Components Regulator Nozzle Guard Trigger Nozzle power Cord pump Housing Container Figure B Page 8 For technical questions, please call 1-888-866-5797. Item 60446...
- Page 9 The work area must not objects not being sprayed and allow access by children or pets to lay cloths (not included) on the floors. prevent distraction and injury. Item 60446 For technical questions, please call 1-888-866-5797. Page 9...
-
Page 10: Before First Use
7. Fill the Container with plain warm water. 12. Reassemble the Spray Gun. 8. Depress the Trigger to spray the plain warm water through the Spray Gun and into a bucket, while shaking the Spray Gun. Page 10 For technical questions, please call 1-888-866-5797. Item 60446... -
Page 11: Material Preparation And Filling
1. Test the consistency by spraying on a piece of scrap material. 2. Adjust the Regulator until proper material flow is achieved. Too Coarse Correct Too Fine (Close (Open Regulator) Regulator) Figure F: Fluid Adjustment Item 60446 For technical questions, please call 1-888-866-5797. Page 11... -
Page 12: Spraying Technique
EVERY use, according to if not cleared immediately. If discontinuing After Every Use on page 14. spraying, clean the Spray Gun according to After Every Use on page 14. Page 12 For technical questions, please call 1-888-866-5797. Item 60446... -
Page 13: Cleaning
Follow the material and solvent IMpORTANT: Do not use mineral spirits manufacturer’s recommendations for with latex paints, doing so will make cleaning, solvent type, and disposal. the paint very difficult to remove. Item 60446 For technical questions, please call 1-888-866-5797. Page 13... - Page 14 Figure J 9. Remove the Nozzle and soak it in solvent 14. Reassemble Spray Gun. until it is clean. Use toothpick to remove any residual material, then rinse in warm water. Page 14 For technical questions, please call 1-888-866-5797. Item 60446...
-
Page 15: Nozzle Assembly Cleaning
Pump Housing. piston Spring Cylinder Nozzle Valve Lubricant Holes Figure K Spent Solvent Disposal After cleaning, dispose of spent solvent according to the solvent manufacturer’s directions and local hazardous waste standards. Item 60446 For technical questions, please call 1-888-866-5797. Page 15... - Page 16 • cracked or broken parts, and • clogged nozzle, • any other condition that may affect its safe operation. Storage Store in a dry, secure area out of reach of children. Page 16 For technical questions, please call 1-888-866-5797. Item 60446...
-
Page 17: Troubleshooting
1. Clean Nozzle. 2. Worn or damaged Nozzle. 2. Replace Nozzle. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power cord and safely discharge pressure before service. Item 60446 For technical questions, please call 1-888-866-5797. Page 17... - Page 18 Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 18 For technical questions, please call 1-888-866-5797. Item 60446...
-
Page 19: Parts List And Diagram
Regulator Screw Bumper Pad Motor Assembly Regulator Index Switch Cotter Pin Regulator Trigger Pump Housing Container Clip Motor Bracket Gasket Right Housing Left Housing Filter Screw Cord Clamp Suction Tube Item 60446 For technical questions, please call 1-888-866-5797. Page 19... -
Page 20: Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.