Direct To-Procedure 1; Direct To-Procedure 2 - Honeywell KLN 900s Pilot's Manual

3.8.1 Direct To-Procedure 1

1. Press D. The Direct To page is displayed on the
left side (figure 3-87). The cursor will already be on
the left page. A waypoint identifier may or may not be
displayed, it doesn't matter at this point.
2. Rotate the left inner knob to select the first character
of the desired waypoint's identifier (figure 3-88).
Remember to enter the "K", "C", or "P" prefix for
certain airports in North America, if required (see
section 2.3, "USE OF ICAO IDENTIFIERS").
3. Turn the left outer knob one step clockwise to move
the flashing portion of the cursor over the second
character position (figure 3-89).
4. Rotate the left inner knob to select the second charac-
ter of the identifier (figure 3-90).
5. Use the left outer and inner knobs as in the previous
steps until the desired identifier is completely dis-
played (figure 3-91).
6. Press E to display the waypoint page on the right
side for the selected waypoint (figure 3-92). Note: If
an incorrect identifier has been entered, you may
immediately start using the left inner knob to enter the
correct identifier.
7. Press E again to approve the displayed waypoint
page. The right side will display the NAV 1 page and
the left side will return to the page which was dis-
played prior to pressing D (figure 3-93). If the Direct
To was started while the NAV 1 page was shown on
the left side or the Super NAV 5 moving map page
was shown, then the left and right pages will revert to
the pages that were shown before the Direct To was
started. The selected waypoint is now the active
Direct To waypoint.
NOTE: In some cases during approach operations, the
KLN 900 presents a page asking how a waypoint is used
when the waypoint identifier is entered character by char-
acter. When this page is presented, simply choose the
desired use of the waypoint (e.g., FAF or MAHP) by mov-
ing the cursor with the left outer knob and pressing E.
Choosing the correct use of the waypoint is required to
ensure proper waypoint sequencing once the aircraft
reaches the waypoint.

3.8.2 Direct To-Procedure 2

1. Select the desired waypoint page on the right side
(figure 3-94) using one of the three procedures
explained in section 3.7, "SELECTING WAYPOINTS".
2. Press D. The Direct To page is displayed on the
left side and it contains the desired waypoint identifier
(figure 3-95).
DIRECT TO: |
K
CRSR
Figure 3-88
DIRECT TO: |
KOAJ
CRSR
Figure 3-90
DIRECT TO: | KOSH
KOSH
CRSR
PRESENT POS|
LGA
N 41^00.03'|ETE
W 73^41.62'|BRG
NAV 2 enr-leg
PRESENT POS| KOSH
LGA
N 41^00.03'|N 43^59.06'
W 73^41.62'|W 88^33.42'
NAV 2 enr-leg
DIRECT TO: | KOSH
KOSH
CRSR
3-28
DIRECT TO: |
|
| K
|
|
|
CRSR
Figure 3-89
DIRECT TO: |
|
| KOSH
|
|
|
CRSR
Figure 3-91
|WITTMAN
|REGL
|
|N 43^59.06'
|W 88^33.42'
enr-leg ent APT 1
Figure 3-92
$=KOSH
|+++++Ê+++++
045^fr|DIS 683nm
15.2nm|GS 193kt
NAV 1
Figure 3-93
|WITTMAN
045^fr|REGL
15.2nm|
APT 1
Figure 3-94
|WITTMAN
|REGL
|
|N 43^59.06'
|W 88^33.42'
enr-leg ent APT 1
Figure 3-95
|
|
|
|
|
|
|
|
|
|
3:34
303^
Rev 2