Table of Contents
Advertisement
Quick Links
DA-682A-DPP Series
Quick Installation Guide
x86 Rackmount Embedded Computers
Moxa Americas:
Toll-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa Europe:
Tel:
+49-89-3 70 03 99-0
Fax:
+49-89-3 70 03 99-99
Moxa India:
Tel:
+91-80-4172-9088
Fax:
+91-80-4132-1045
Edition 1.0, March 2016
Technical Support Contact Information
www.moxa.com/support
2016 Moxa Inc. All rights reserved.
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel:
+86-21-5258-9955
Fax:
+86-21-5258-5505
Moxa Asia-Pacific:
Tel:
+886-2-8919-1230
Fax:
+886-2-8919-1231
P/N: 1802006820120
*1802006820120*
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Moxa Technologies DA-682A-DPP Series
Summary of Contents for Moxa Technologies DA-682A-DPP Series
-
Page 1: Quick Installation Guide
DA-682A-DPP Series Quick Installation Guide x86 Rackmount Embedded Computers Edition 1.0, March 2016 Technical Support Contact Information www.moxa.com/support Moxa Americas: Moxa China (Shanghai office): Toll-free: 1-888-669-2872 Toll-free: 800-820-5036 Tel: 1-714-528-6777 Tel: +86-21-5258-9955 Fax: 1-714-528-6778 Fax: +86-21-5258-5505 Moxa Europe: Moxa Asia-Pacific:... - Page 2 Overview The DA-682A-DPP series of computers are x86-based hardware platforms with VGA, six Gigabit Ethernet ports, CompactFlash, USB, and two PCI ports for expansion modules. The DA-682A-DPP is available in three basic modules with different CPU options, giving designers the flexibility to choose the DOM (Disk on Module) option, RAM option, and operating system as per their requirements.
-
Page 3: Hardware Installation
Hardware Installation Front View Rear View Connecting the Power The DA-682A-DPP has dual power inputs. Use a Phillips screwdriver to remove the terminal clamp screws. Connect the power cord to the screws, and then fasten the screws to the unit. Refer to the following figure for detailed information: AC Terminal DC Terminal... - Page 4 Power Terminal Block Pin Assignment Terminal Description Note Number PWR1 Line/DC+ is connected to the positive PWR1 Line/DC+ (+) terminal if the power source is DC, or to the Line terminal if the power source is AC. PWR1 PWR1 Neutral/DC- is connected to the Neutral/DC- negative (-) terminal if the power source is DC, or to the Neutral terminal if the power...
-
Page 5: Installing Expansion Modules
Connecting to a Display The VGA hardware interface is a D-Sub 15-pin female connector. Be sure to cut off system power before you connect or disconnect the monitor cable. USB Ports The DA-682A-DPP comes with four USB 2.0 ports, two on the rear panel, and two on the front. -
Page 6: Configuring The Ethernet Interface
Configuring the Ethernet Interface Linux users should follow these steps: If you use the console cable to configure network settings for the first time, use the following commands to edit the interfaces file. STEP 1: Take all network interfaces offline, before you reconfigure the LAN settings using the following command: MOXA:~# ifdown –a STEP 2: Edit the network interfaces file. - Page 7 Win 7 users should follow these steps: Step 1: Go to Start Control Panel Network and Internet Network Connections. Step 2: In Local Area Connection Properties, select Internet Protocol Version 4 (TCP/IPv4) and click Properties. Step 3: Click OK after entering the preferred IP address and netmask. NOTE Refer to the DA-682A-DPP software user’s manual for the OS installed on your machine for additional configuration information.
Need help?
Do you have a question about the DA-682A-DPP Series and is the answer not in the manual?
Questions and answers