KROHNE ifc 300 Handbook page 42

No. Text displayed
st
C 4.3 1 meas. page 1
and / or
nd
C 4.4 2 meas. page 2
C 4.z.01 Function
C 4.z.02 Measurement 1
C 4.z.03 Range
C 4.z.04 Limitation
C 4.z.05 Low flow cutoff
C 4.z.06 Time constant
st
C 4.z.07 Format 1 line
C 4.z.08 Measurement 2
nd
C 4.z.09 Format 2
C 4.z.10 Measurement 3
rd
C 4.z.11 Format 3 line
C 4.6 Special functions
.01 Error reset
C 4.6
.02 Save settings
C 4.6
C 4.6.03 Load settings
C 4.6.04 Password Quick Set
C 4.6.05 Password Setup
C 4.6.06 GDC IR interface
42
Description and settings
All functions and settings for the two pages are identical!
In the following descriptions "z" characterizes
the m.v. page:
• one line
st
line • flow speed
• volume flow
• mass flow
Unit and format depend on measured quantity selected under C 4.z.02
xxx %
xxxx.x ... ±xxxx.x unit dependent on measured variable selected
1st value ≥ 2nd value (hysteresis), values around "0" are set to "0"
xxx.x s
Setting of dec. places acc. to list: • X (none) ... X.XXXXXXXX (8 places)
nd
line • flow speed
• conductivity
• volume flow
• mass flow
line Setting of dec. places acc. to list: • X (none) ... X.XXXXXXXX (8 places)
rd
line • flow speed
• volume flow
• mass flow
Setting of dec. places acc. to list: • X (none) ... X.XXXXXXXX (8 places)
Select:
such as "line failure", "counter overflow", etc.)
• Backup 1
• No
• Cancel
With this function, complete device data records can be written into the Backup
1, 2 memories and from there be reloaded (see below)
• Factory settings
• Backup 1
• No
Activates 4-character password for changes in the Quick Setup Menu.
0000 deactivates the password.
Activates 4-character password for changes in the Setup Menu and
in the Test Menu.
0000 deactivates the password.
Select:
• page 1 = C 4.3
• two lines • three lines
(100 % ≤ value ≤ 999 %)
(setting range 000.0 ... 100.0 s)
• coil temperature
• counter 1
• counter 2
• bar graph
• conductivity
• coil temperature
• Operating hours
• No • Yes
(reset errors that are not automatically deleted,
select, then press ↵
• Backup 2
confirm with ↵ or start Backup
• Yes
exit Backup function with ↵
load settings
Press ↵ key, IR-Interface not activated, and
• cancel
exit this function
Press ↵ key, IR-Sensor is activated, and
• activate
accept all changes made up to now
Within the next 60 sec. position the IR-Interface
with the suction cups on the pane of the housing.
The correct position is indicated by the steady
bright red LED of the interface,
as soon as the red LED and the IR-Sensor (below
the keys on the display) are roughly one above the
other, see Fig. in Sect. 4.2.
IFC 300
• page 2 = C 4.4
• coil temperature
• conductivity
• Operating hours
Selection dependent on
Function C 4.z.01
• counter 1
• counter 2
• Factory settings
• Backup 1
• No
03 / 2005