KROHNE IFC 300 Supplementary Instructions Manual

KROHNE IFC 300 Supplementary Instructions Manual

Signal converter for electromagnetic flowmeters
Hide thumbs Also See for IFC 300:

Advertisement

IFC 300
IFC 300
IFC 300
IFC 300
Supplementary Instructions
Supplementary Instructions
Supplementary Instructions
Supplementary Instructions
Signal converter for electromagnetic flowmeters
Description of PROFINET IO interface
Description of PROFINET IO interface
Description of PROFINET IO interface
Description of PROFINET IO interface
Electronic Revision: ER 3.4.0
The documentation is only complete when used in combination with the relevant
documentation for the flow sensor.
© KROHNE 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IFC 300 and is the answer not in the manual?

Questions and answers

Summary of Contents for KROHNE IFC 300

  • Page 1 Description of PROFINET IO interface Description of PROFINET IO interface Electronic Revision: ER 3.4.0 The documentation is only complete when used in combination with the relevant documentation for the flow sensor. © KROHNE 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 2: Table Of Contents

    4.7 Start-up parameter configuration ................. 17 4.7.1 General settings........................18 4.7.2 Measurement settings ......................18 4.7.3 Unit settings .......................... 19 4.7.4 Totalizer 1 settings........................ 20 4.7.5 Totalizer 2 settings........................ 20 www.krohne.com 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 3 4.8.3 Diagnosis blocks ........................21 4.8.4 Cyclic data structure......................22 4.8.5 Input data ..........................22 4.8.6 Output data..........................24 4.9 Totalizer .......................... 25 4.10 Status information......................26 5 Notes 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en www.krohne.com...
  • Page 4: Introduction

    IFC 300 1.1 Scope of the document These instructions are supplementary to the standard handbook of the IFC 300 with ER 3.4.0 (refer to document MA IFC 300 R05). They provide additional information for the devices when being operated and connected to a PROFINET IO network.
  • Page 5: Device Description

    This device is a digital device used exclusively as an electronic control system utilised by a public utility or in an industrial plant. INFORMATION! This PROFINET IO device is certified by the PROFIBUS Nutzerorganisation e.V. 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en www.krohne.com...
  • Page 6: Technical Data

    - Network diagnostics via IP (SNMP) - Topology information (LLDP) with LLDP-MIB Cabling - IEC 61784-5-3 - Copper Typical application - Factory Automation - Process Automation Table 2-1: Supported PROFINET IO Conformance Class www.krohne.com 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 7: Electrical Connections

    These instructions also contain detailed descriptions on how to use grounding rings and how to install the flow sensors in metal or plastic pipes or in pipes which are coated on the inside. 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en www.krohne.com...
  • Page 8: Profinet Io Cable Types

    ISO/IEC 11801 Edition 2.0 Amendment 2, Class D at least Category 5 Category (min.) ISO/IEC 11801 Edition 2.0 Connector Category 5 Shielding Cable strain relief IEC 61984 Mating cycles Min. 50 Table 3-2: Recommended cabling www.krohne.com 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 9: Electrical Connection Of Profinet Io

    Unused M12 connectors must be covered by a cap to protect the connector from dust and • humidity. Straight M12 connectors are recommended. • Standardised M12 connectors (IP66/67 or higher) must be used and are described in the following standards: IEC 61076-2-101 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en www.krohne.com...
  • Page 10: Assembly Of The M12 Power Supply Connector With Profinet Io

    3.4.3 Assembly of the M12 data connector with PROFINET IO Figure 3-2: PROFINET IO M12 data connector (female, D coded) Number Signal Colour yellow white orange blue Table 3-5: PROFINET IO M12 data connector pinout and colouring scheme www.krohne.com 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 11: Assembly Of The Terminals With Profinet Io

    Devices with two Ethernet connectors can still be used. The unused connectors must be covered by the provided caps (for details refer to Overview of the PROFINET IO M12 connectors on page Figure 3-3: Point-to-point or star topology 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en www.krohne.com...
  • Page 12: Line Topology

    The control system must support this topology. This topology is typically preferred if redundancy is required. INFORMATION! Devices in this network topology need two Ethernet ports. Figure 3-5: Ring topology www.krohne.com 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 13: Operation

    4.1.2 Device discovery and identification (DCP signal) To identify the device, the DCP signal service can be used. While a DCP signal is active a correspondent message is shown on the device display status page (for details refer to IFC 300 handbook).
  • Page 14: Display Menu

    Standard PROFINET IO DAP with up to 2 ports 32768 Interface 32769 Port 1 32770 Port 2 Sensors Module representing the sensor system Sensor Data I/O data, start-up records Table 4-4: Static PROFINET IO slot/subslot mapping www.krohne.com 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 15: Data Types And Byte Order

    (UINT) or bit-wise (WORD) depending on context. Byte order on bus Significance Example Value = 1234 0x04 0xD2 Table 4-6: Data type Unsigned16 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en www.krohne.com...
  • Page 16: Information & Maintenance (I&M)

    Table 4-8: Description of I&M1 4.5.3 I&M2 - Installation date I&M2 parameters can be changed by user. Name Length Description INSTALLATION_DATE Date of installation or commissioning. Table 4-9: Description of I&M2 www.krohne.com 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 17: I&M3 - Descriptor

    PROFINET IO connection is established. The following sections provide a list of all parameters within the record data. A unique parameter ID (ID) is introduced in order to reference each parameter explicitly. 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en www.krohne.com...
  • Page 18: General Settings

    Unit: selected by ID 14 Empty Pipe Detection Unsigned8 Turn empty pipe detection on or off. Note: empty pipe detection is based on conductivity measurement. Table 4-13: Parameter group - Measurement settings www.krohne.com 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 19: Unit Settings

    Unit selector for flow velocity values. Level Unsigned16 Unit selector for level values. 1 Table 4-14: Parameter group - Unit settings 1 Only available for signal converters with a TIDALFLUX flow sensor. 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en www.krohne.com...
  • Page 20: Totalizer 1 Settings

    Low flow cut-off hysteresis if measurement (ID 24) is set to "Mass flow". Unit: selected by ID 8 Table 4-16: Parameter group - Totalizer 2 settings 1 Only available for signal converters with a TIDALFLUX flow sensor. www.krohne.com 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 21: Cyclic Data

    The totalizer can be controlled by the corresponding control octet in the output data (for details Output data refer to on page 24). 4.8.3 Diagnosis blocks A diagnosis block provides a list of bits that give information about the internal device diagnosis. 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en www.krohne.com...
  • Page 22: Cyclic Data Structure

    Conductivity – Status 1 Status 36...37 Unsigned16 For details refer to information on page 26. Units of 38...39 Conductivity – Unit 1 Unsigned16 For details refer to measurement on page 17. www.krohne.com 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 23 Cyclic diagnosis (Octet 5) Unsigned8 Cyclic diagnosis (Octet 6) Unsigned8 Cyclic diagnosis (Octet 7) Unsigned8 Table 4-18: Input data 1 No valid values when used with CAPAFLUX flow sensor! 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en www.krohne.com...
  • Page 24: Output Data

    Reserved / don't care 0 – Calculate min/max values of corrected volume flow measurement 1 – Stop min/max calculation and reset both values 1...7 Reserved / don't care Table 4-19: Output data www.krohne.com 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 25: Totalizer

    This example assumes a constant flow that is being totalized. Figure 4-1: Example for totalizer control X: time Y1: totalizer value Y2: totalizer run/stop Y3: totalizer reset Value Description STOP RESET 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en www.krohne.com...
  • Page 26: Status Information

    Initial value as long as no measurement is available. UNCERTAIN - process related 0x78 Process value is potentially invalid (accuracy not guaranteed). GOOD 0x80 Valid process value. 0x01 Simulation running. Table 4-20: Status coding www.krohne.com 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en...
  • Page 27: Notes

    NOTES IFC 300 09/2017 - 4005824401 - AD IFC 300 Profinet R01 en www.krohne.com...
  • Page 28 • Process Analysis • Services Head Office KROHNE Messtechnik GmbH Ludwig-Krohne-Str. 5 47058 Duisburg (Germany) Tel.: +49 203 301 0 Fax: +49 203 301 10389 info@krohne.com The current list of all KROHNE contacts and addresses can be found at: www.krohne.com...

Table of Contents

Save PDF