General Comments - Marantz CDR630 Owner's Manual

CD RE
CO RD
ER
PO W ER
ON /O FF
PH ON
ES
LE VE L
0
10
Re cor dab
le
Note:
- Check to ensure that the recording side of the disc is clean (See
Disc Maintenance).
- If you insert a blank disc or non-finalized CD-R or CD-RW in the
drawer, the recorder will calibrate the disc for optimum recording.
During this process, the display will first show OPC and then the
recording time used and the last track number.
Removing discs
1 Press the OPEN/CLOSE button (6) on the front of the appliance
to open the disc drawer.
2 Remove the disc from the drawer.
3 Gently press the front of the drawer or press the OPEN/CLOSE
button (6) to close the drawer.
RECORDING
The numbers between parentheses refer to the fold-out illus-
tration.

General Comments

Make sure the display indicator 'CD-RECORDABLE' or 'CD-
REWRITABLE' is on; the recording procedure is the same for both
types of disc.
DIG AUTO TRACK REPEAT 1 TOTAL
ANALOG
PROG
RECORDABLE L
-50 -40 -30 -20
R
CD
REWRITABLE
If the disc already contains recordings, the CD Recorder will auto-
matically search for the end of the last track so that recording can
be started from there.
Recordings can only be made if there are at least seven seconds of
recording time left on the disc. You can check this by pressing the
Display button (18), after which the remaining recording time will be
shown.
A maximum total of 99 tracks can be recorded on a disc.
8
DIG
AU TO TRA
CK
TOT AL
REM
TIM E
CD SYN
C
REC ORD
DI SP LA
L
CD
REW RIT -50
ABL E -40
R -30
-20
-10
-6
-3 PAU SE
0
0VER
COP Y IN PU T
AU TO
/ MA N
OP EN
/ CL OS
REM TRACK TIME CD SYNC
RECORD
FINALIZE
ERASE
-10 -6 -3 0
OVER
PAUSE
Attention!
Never switch the CD Recorder off when recording;
this can damage the disc.
If a power failure occurs during recording, the CD
Recorder will attempt to repair the disc as soon as the
power is restored; during this procedure, the display
Y
will indicate R R E E C C O O V V E E R R . If recover is unsuccessful,
discard that disc because it may no longer read/record.
E
DIG AUTO TRACK
ANALOG
PROG
RECORDABLE
CD REWRITABLE
Manually recording an analog source
Preparing to begin recording
Make sure the disc is free of scratches and/or dust particles.
1 Press the INPUT button (19) until ANALOG appears on the dis-
play.
DIG AUTO TRACK
ANALOG
PROG
RECORDABLE
CD REWRITABLE
2 By pressing AUTO/MANUAL (17), you can select manual or
automatic track marking. If "automatic" is selected, 'AUTO
TRACK' will appear on the display.
DIG AUTO TRACK
ANALOG
PROG
RECORDABLE
CD REWRITABLE
With automatic increments, a new track number will be auto-
matically added after a silence (< -50dB) on the original of at
least three seconds; track numbers cannot be added manually.
With manual increments, you can add track numbers at any
time during recording by pressing REC (7) or TRACK INCR
(37) (on the remote control); the minimum track length is four
seconds. Track numbers cannot be added after recording.
Attention!
If the original has pauses lasting less than three sec-
onds, the track numbers should be increased manual-
ly. If you are recording from LP's, it is recommended
that you always select manual operation of the track
numbering.
To start recording
1 Press the REC (7) button to enter the Record-Pause mode. The
display indicator will start to flash 'RECORD'
REPEAT 1 TOTAL REM TRACK TIME CD SYNC
RECORD
FINALIZE
ERASE
L
-50 -40 -30 -20 -10 -6 -3 0 OVER
R
PAUSE
REPEAT 1 TOTAL REM TRACK TIME CD SYNC
RECORD
FINALIZE
ERASE
L
-50 -40 -30 -20 -10 -6 -3 0 OVER
R
PAUSE
REPEAT 1 TOTAL REM TRACK TIME CD SYNC
RECORD
FINALIZE
ERASE
L
-50 -40 -30 -20 -10 -6 -3 0 OVER
R
PAUSE