Marantz CDR630 Owner's Manual page 8

2 Press the PLAY button (13) to start recording and immediately
start the digital source.
The relevant track number and the recording time used will
appear on the display. Press DISPLAY (18) to view the total
remaining recording time.
3 Press STOP (15) to stop recording in either the manual or auto-
matic mode.
In the automatic mode, recording will stop after a twenty-
second silence (-50dB) on the original.
Note:
- You can also use the PAUSE button (14) instead of the STOP
(15) button if you want to stop and re-enter the Record-Pause
mode.
- After recording, the temporary table of contents will be automati-
cally up-dated. During this process, the display will indicate
UPDATE .
DIG AUTO TRACK REPEAT 1 TOTAL
ANALOG
PROG
RECORDABLE L
-50 -40 -30 -20
R
CD REWRITABLE
Attention!
If you want to play the disc in a different, regular CD-
player, the disc must be finalized. See 'Finalizing
discs' p. 11.
Automatic recording from a digital
source
In order to make recordings easily and quickly, the recorder is
equipped with the handy CD-SYNC function. This function can be
used to synchronously record individual tracks or entire discs. The
original may be a CD, DAT or MD, or any compatible digital source.
Preparations for recording
1 Press the INPUT button (19) a number of times until (depend-
ing on the connection used) CXL SRC , CXL 44 , OPT SRC
or OPT 44 appears on the display.
DIG AUTO TRACK REPEAT 1 TOTAL
ANALOG
PROG
RECORDABLE L
-50 -40 -30 -20
CD R
REWRITABLE
Note:
- If you try to make a full (1 to 1) copy [OPT 44, CXL 44] of a digi-
tal source that does exceed the 44.1 kHz +/- 100 ppm range,
recording will most likely not start. In some rare cases, mutes
may occur and recording may stop. Use a better source or use
OPT SRC or CXL SRC to avoid these problems.
Do not start the digital source yet.
10
REM TRACK TIME CD SYNC
RECORD
FINALIZE
ERASE
-10 -6 -3 0 OVER
PAUSE
REM TRACK TIME
CD SYNC
RECORD
FINALIZE
ERASE
-10 -6 -3 0
OVER
PAUSE
To start recording
1 To record a single track, press CD-SYNC (10) once to record
one track; SYNC-1 will appear on the display. To record all
tracks, press CD-SYNC (10) twice in rapid succession to
record all tracks; SYNC will appear on the display.
DIG AUTO TRACK REPEAT 1 TOTAL
ANALOG
PROG
RECORDABLE L
-50 -40 -30 -20
R
CD REWRITABLE
Wait until the pause setting is activated and the display indica-
tor 'RECORD' starts to flash.
DIG AUTO TRACK REPEAT 1 TOTAL
ANALOG
PROG
RECORDABLE L
-50 -40 -30 -20
R
CD REWRITABLE
If the digital connection is incorrect, the display indicator 'DIG' will
flash.
REPEAT 1
DIG AUTO TRACK TOTAL
ANALOG
PROG
RECORDABLE L
-50 -40 -30 -20
R
CD REWRITABLE
If the digital source exceeds the 44.1 kHz +/- 100 ppm range
and CXL44 or OPT44 is selected, the display indicator DIG will
flash. When the source gets better (for example by adjusting a
bad cable connection) the label stops blinking.
2 Press Play on the digital source.
The CD Recorder will now automatically start to record. If you
start the source in the middle of a track, automatic Synchro
recording will not commence until the beginning of the next
track.
The relevant track number and the recording time used will
appear on the display.
To view the recording time remaining, press DISPLAY (18).
3 Press STOP (15) to stop recording.
In the automatic mode, recording will stop after a twenty-
second silence (<-50dB) on the source.
Note:
- You can also use the PAUSE button (14) instead of STOP (15)
to stop and re-enter the Record-Pause mode.
- After recording, the temporary table of contents will be automati-
cally up-dated. During this process, the display will indicate
UPDATE .
DIG AUTO TRACK REPEAT 1 TOTAL
ANALOG
PROG
RECORDABLE L
-50 -40 -30 -20
R
CD REWRITABLE
REM TRACK TIME CD SYNC
RECORD
FINALIZE
ERASE
-10 -6 -3 0 OVER
PAUSE
REM TRACK TIME CD SYNC
RECORD
FINALIZE
ERASE
-10 -6 -3 0 OVER
PAUSE
REM TRACK TIME CD SYNC
RECORD
FINALIZE
ERASE
-10 -6 -3 0
OVER
PAUSE
REM TRACK TIME CD SYNC
RECORD
FINALIZE
ERASE
-10 -6 -3 0 OVER
PAUSE