Siemens MICROMASTER 440 Series Operating Instructions Manual page 65

5 System Parameters
Alarms, Warnings and Monitoring (P0004 = 21)
Par. No.
r0947[8]
r0948[12]
P0952
P2100[3]
P2101[3]
r2110[4]
P2111
r2114[2]
P2115[3]
P2150[3]
P2151[3]
P2152[3]
P2153[3]
P2155[3]
P2156[3]
P2157[3]
P2158[3]
P2159[3]
P2160[3]
P2161[3]
P2162[3]
P2163[3]
P2164[3]
P2165[3]
P2166[3]
P2167[3]
P2168[3]
r2169
P2170[3]
P2171[3]
P2172[3]
P2173[3]
P2174[3]
P2176[3]
P2177[3]
P2178[3]
P2179
P2180
P2181[3]
P2182[3]
P2183[3]
P2184[3]
P2185[3]
P2186[3]
64
Parametername
Last fault code
Fault time
Total number of faults
Alarm number selection
Stop reaction value
Warning number
Total number of warnings
Run time counter
AOP real time clock
Hysteresis frequency f_hys
CI: Monitoring speed setpoint
CI: Act. monitoring speed
Time-constant speed filter
Threshold frequency f_1
Delay time of threshold freq f_1
Threshold frequency f_2
Delay time of threshold freq f_2
Threshold frequency f_3
Delay time of threshold freq f_3
Min. threshold for freq. setp.
Hysteresis freq. for overspeed
Entry freq. for perm. deviation
Hysteresis frequency deviation
Delay time permitted deviation
Delay time ramp up completed
Switch-off frequency f_off
Delay time T_off
CO: Act. filtered frequency
Threshold current I_thresh
Delay time current
Threshold DC-link voltage
Delay time DC-link voltage
Torque threshold T_thresh
Delay time for torque threshold
Delay time for motor is blocked
Delay time for motor is stalled
Current limit for no load ident.
Delay time for no load ident.
Belt failure detection mode
Belt threshold frequency 1
Belt threshold frequency 2
Belt threshold frequency 3
Upper torque threshold 1
Lower torque threshold 1
http://nicontrols.com
International English
Default Acc WS
- 2 -
- 3 -
0 3 CT
0 3 CT
0 3 CT
- 2 -
0 3 CT
- 3 -
0 3 CT
3.00 3 CUT
0:0 3 CUT
0:0 3 CUT
5 2 CUT
30.00 3 CUT
10 3 CUT
30.00 2 CUT
10 2 CUT
30.00 2 CUT
10 2 CUT
3.00 2 CUT
20.00 2 CUT
3.00 2 CUT
3.00 3 CUT
10 2 CUT
10 2 CUT
1.00 3 CUT
10 3 CUT
- 2 -
100.0 3 CUT
10 3 CUT
800 3 CUT
10 3 CUT
5.13 2 CUT
10 2 CUT
10 2 CUT
10 2 CUT
3.0 3 CUT
2000 3 CUT
0 2 CT
5.00 3 CUT
30.00 2 CUT
50.00 2 CUT
99999.0 2 CUT
0.0 2 CUT
MICROMASTER 440 Operating instructions
6SE6400-5CA00-0BP0
QC
-
-
N
N
N
-
N
-
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
-
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N