Page 1 Uconnect 8.4/8.4 NAV Owner’s Manual Supplement...
Page 2: Safety Guidelines 3
ALL ABOUT UCONNECT ACCESS ........
Page 4 SAFETY GUIDELINES CONTENTS SAFETY GUIDELINES ....4 CYBERSECURITY ......7...
Page 5: Safety Guidelines
Only use to a level that still allows you to hear outside traffic Uconnect when it is safe to do so. Failure to do so and emergency vehicles. may result in an accident involving serious injury or death.
Page 6 SAFETY GUIDELINES 5 • Permanent hearing loss may occur if you play your • Do not spray any liquid or caustic chemicals directly music or the system at loud volumes. Exercise caution on the screen! Use a clean and dry micro fiber lens when setting the volume on your system.
Page 7 6 SAFETY GUIDELINES FCC Declaration If this equipment does cause harmful interference to radio or television reception, which can be determined by This device complies with Part 15 of the FCC Rules and turning the equipment off and on, the user is encouraged with Industry Canada license-exempt RSS standard(s).
Page 8: Cybersecurity
The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent CYBERSECURITY version of vehicle software (such as Uconnect software) is installed. Your vehicle may be a connected vehicle and may be equipped with both wired and wireless networks.
Page 9 • ONLY insert media (e.g., USB, SD card, or CD) into learn about available Uconnect software updates. your vehicle if it came from a trusted source. Media • Only connect and use trusted media devices (e.g. of unknown origin could possibly contain mali- personal mobile phones, USBs, CDs).
Page 10 Third parties may unlawfully intercept information and private communications without your consent. For further information, refer to “Privacy Prac- tices” in “All About Uconnect Access” in your Owner’s Manual Radio Supplement and “Onboard Diagnostic System (OBD II) Cybersecurity” in “Maintaining Your...
Page 12 IDENTIFYING YOUR RADIO CONTENTS IDENTIFYING YOUR RADIO ....12...
Page 13 • Hands-free/Bluetooth • USB port, AUX jack and SD Card slot — If Equipped • Touchscreen Climate Controls • SiriusXM Satellite Radio with 1 year Trial Included — If Equipped • Uconnect Access — U.S. Market Only — If Equipped...
Page 14 IDENTIFYING YOUR RADIO 13 • SiriusXM Traffic with 5 year Trial Included — U.S. The 8.4AN sets itself apart by offering these unique features: Market Only — If Equipped • HD Radio — U.S. Market Only • SiriusXM Travel Link with 5 year Trial Included — U.S. Market Only —...
Page 16: Table Of Contents
INTRODUCTION TO UCONNECT ACCESS . . .17 ▫ What Is Uconnect Access? ....17 USING UCONNECT ACCESS ....28 ▫...
Page 17 DEVICE CONNECTION AND AUDIO TIPS WITH UCONNECT ......97 ▫ How To Remove My Uconnect Access...
Page 18: Introduction To Uconnect Access
Uconnect features and applications in this vehicle. Only use Uconnect when it is safe to do so. Failure to do so may result in an accident involving serious injury or death.
Page 19 Owner Connect website (moparownerconnect.com) and Uconnect Care. 2. The Uconnect “Apps” Button On The Menu Bar Of • The functionality to turn your vehicle into a WiFi The In-Vehicle Touchscreen Hotspot on demand.
Page 20 ALL ABOUT UCONNECT ACCESS 19 3. The Uconnect Voice Command And Uconnect Phone Buttons On Your Steering Wheel The buttons let you use your voice to give commands, make phone calls, send and receive text messages hands-free, enter navigation destinations and control your radio and media devices.
Page 21: All About Uconnect Access 15
20 ALL ABOUT UCONNECT ACCESS 1 — Uconnect Phone Button 7 — Uconnect Access 8.4AN Radio 2 — Uconnect Voice Command Button 8 — Back Button 3 — Phone Hang Up Button 9 — Tune or Scroll Knob/Browse or Enter Button 4 —...
Page 22: Included Trial Period For New Vehicles
Included Trial Period For New Vehicles ship. Your new vehicle may come with an included trial period for use of the Uconnect Access Services starting at the date of vehicle purchase. To activate the trial, you must Included Trial on New Vehicles ONLY Radio Uconnect 8.4A...
Page 23 • Both the Uconnect 8.4A and Uconnect 8.4AN feature a large 8.4 inch full color touchscreen. • Only the Uconnect 8.4AN will have the HD Radio icon when listening to FM or AM stations. The icon will be lit when it is receiving an HD Radio signal (not all...
Page 24: Features And Packages
Mopar Owner Connect website (moparownerconnect.com). If you need assistance, you can also call Uconnect Care at 855-792-4241. For the latest information on packages and pricing information, visit DriveUconnect.com. GETTING STARTED WITH UCONNECT ACCESS Registration 2. Press the “Uconnect Care” button on the touchscreen.
Page 25: Download The Uconnect Access App
For further information please visit DriveUconnect.com. To link your internet radio accounts: Download The Uconnect Access App 1. Download the Uconnect Access App to your mobile device. You’re only a few steps away from using remote com- mands and playing your favorite music in your car.
Page 26: Purchasing Apps And Wifi Hotspot For Your Vehicle
Images are placed here to represent the FCA US LLC Apps and WiFi Hotspot can be purchased from the vehicles (Chrysler, Jeep, Dodge, Ram and FIAT) you Uconnect Store from within your vehicle, and online at own. If a vehicle you own is not shown here, click on Mopar...
Page 27 Access App. Device compatibility can be verified at Other vehicles you own may not have Uconnect Ac- UconnectPhone.com. For more details, see the section cess and will indicate that it is a non-Uconnect Access labeled Download the Uconnect Access App. Vehicle.
Page 28 “yes” (message and corner of the page. data rates may apply, please see your mobile phone 3. Click the Uconnect Notifications tab on the left side of provider for details). If you have questions, text the page.
Page 29: Using Uconnect Access
Uconnect 8.4A or 8.4AN radio. • Favorite Apps — this is a good place to put the Apps • Uconnect Access via Mobile (if equipped) — uses the you use most frequently. Uconnect Access App and your device’s data plan to •...
Page 30: 9-1-1 Call
NOTE: Most Uconnect Access features do not require Access To Emergency Services At The Push Of A Button that you have a compatible device. The Uconnect Access features must have an operable 1X (voice/data) or 3G (data) network connection and you must be registered with Uconnect Access with an active subscription.
Page 31 30 ALL ABOUT UCONNECT ACCESS Description 2. Once a connection between the vehicle and a 9-1-1 operator is made, the 9-1-1 Call system will transmit 9-1-1 Call is a feature that, at the push of a button, can the following important vehicle information to a 9-1-1 contact emergency services.
Page 32 ALL ABOUT UCONNECT ACCESS 31 9-1-1 Call System Limitations Even if the 9-1-1 Call system is fully functional, factors beyond FCA US LLC’s control may prevent or stop 9-1-1 Vehicles sold in Canada and Mexico DO NOT have 9-1-1 Call system operation. These include, but are not limited Call system capabilities.
Page 33 9-1-1 Call System, • This feature is available only on vehicles sold in the among other vehicle systems, will not operate. U.S. • Vehicle must be properly equipped with the Uconnect Access System.
Page 34 1X (voice/data) or 3G (data) and GPS ANY REASON (INCLUDING DURING OR AF- signal reception, which can prevent your vehicle TER AN ACCIDENT) THE UCONNECT FEA- from placing an emergency call. An operable 1X TURES, APPS AND SERVICES AMONG OTHERS (voice/data) or 3G (data) network connection and a WILL NOT OPERATE.
Page 35 34 ALL ABOUT UCONNECT ACCESS WARNING! (Continued) WARNING! (Continued) • The Occupant Restraint Controller (ORC) turns on • If anyone in the vehicle could be in danger (e.g., the Air Bag Warning Light on the instrument panel fire or smoke is visible, dangerous road conditions...
Page 36: Roadside Assistance Call
ALL ABOUT UCONNECT ACCESS 35 2. What Type Of Information Is Sent When I Call 9-1-1 Roadside Assistance Call From My Vehicle? Certain vehicle information, such Easy Call To Roadside Assistance 24/7 Using ASSIST as make and model, is transmitted along with last Button known GPS location.
Page 37 • Uconnect Care — In vehicle support for Uconnect assistance or support. Access System, Apps, and Features.
Page 38 ALL ABOUT UCONNECT ACCESS 37 • Vehicle must be properly equipped with the Uconnect Access System. • Vehicle must have an operable 1X (voice/data) or 3G (data) network connection. • Vehicle must be registered with Uconnect Access and have an active subscription that includes the appli- cable feature or App.
Page 39: Yelp
2. If I Am Subscribed To Uconnect Access, Does It Cover Towing Or Other Expenses Incurred By Using FCA Roadside Assistance? No, however your new vehicle may include Roadside Assistance services.
Page 40 ALL ABOUT UCONNECT ACCESS 39 Here is what Yelp can do for you while you are on the How It Works road: 1. Using the touchscreen, launch Yelp by pressing Apps • Deliver a list of up to 20 results, prioritizing by best >...
Page 41 Requirements wash.” After the beep, say “restaurants.” • Vehicle must be properly equipped with the Uconnect 4. The Uconnect system will link out to the cloud to do Access System. your Yelp search, and depending on your search • Your vehicle must be in range of an operable 1X request, this may take up to 30 seconds.
Page 42 Only use is Best Match). Uconnect when it is safe to do so. Failure to do so • The Rating tab will re-sort your search based on may result in an accident involving serious injury ratings submitted by everyday users to Yelp’s online...
Page 43: Security Alarm Notification
1. Log on to the Mopar Owner Connect website installed theft alarm system has been set-off. You’ve (moparownerconnect.com) using the username and probably seen this before, a vehicle’s alarm goes off in a password you used when registering your Uconnect Access system.
Page 44 7. You’re all set. Should your theft alarm go off, a page. notification(s) will be sent to the number(s) and/or 4. If you have more than one vehicle with Uconnect email(s) you provided. Access, please select which vehicle you want to man- Requirements age notifications for using the drop down menu.
Page 45 44 ALL ABOUT UCONNECT ACCESS • Vehicle must be registered with Uconnect Access and FAQs have an active subscription that includes the appli- 1. What do I do if my Theft Alarm goes off? In the event cable feature or App.
Page 46: Stolen Vehicle Assistance
ALL ABOUT UCONNECT ACCESS 45 3. Can I receive a text message (SMS) when my Theft Uconnect Care Agent will ask for the stolen vehicle report Alarm goes off? Yes. Text messages are a convenient number issued by local law enforcement. As long as your and quick way to receive notifications.
Page 47 46 ALL ABOUT UCONNECT ACCESS How It Works 4. Uconnect Care will work with your local law enforce- ment to track and attempt to recover the vehicle. You 1. If your vehicle is stolen, contact local law enforcement will be contacted by law enforcement if your vehicle is as soon as possible.
Page 48 They will work with you provide the Uconnect Care Agent with the stolen you to file a stolen vehicle report. Then call Uconnect vehicle report, the agent will work together with law Care at:1-855-792-4241 Inform Uconnect Care that enforcement to try to locate your vehicle.
Page 49: Wifi Hotspot
1X (voice/data) or 3G (data) private in-vehicle network. network using Uconnect Access and is ready to go where ever you are. Once your vehicle is registered for Uconnect Access, you can purchase a WiFi Hotspot...
Page 50 Store. the internet. NOTE: You must set up your Uconnect Payment Account on the Mopar Owner Connect website and establish a Uconnect Payment PIN to purchase WiFi Hotspot. 2. After purchasing WiFi Hotspot, it will be enabled/ turned on in your vehicle.
Page 51 50 ALL ABOUT UCONNECT ACCESS 3. WiFi Hotspot should be turned on after purchasing a 4. From your in-vehicle touchscreen, select the appropri- subscription. To disable WiFi Hotspot, simply press to ate in-vehicle network and the desired security level uncheck the box to the right of the App (this feature is setting.
Page 52: Voice Texting
Hotspot. 5. From your Wi-Fi enabled device (laptop, tablet, etc.). Voice Texting • Search for and select the Uconnect hotspot in the Add Free-Form Voice Texts To Your Voice Text Reply settings of your device. Feature •...
Page 53 52 ALL ABOUT UCONNECT ACCESS as if you were talking to the recipient, and the Uconnect to white. This is an indicator that Voice Texting will work Access voice-texting technology will convert your voice with your device. Outgoing voice texts may not be into a text message.
Page 54 ALL ABOUT UCONNECT ACCESS 53 3. The system will respond “Say the phone number or the full name and the phone type of the contact that you want to send a message to.” 4. Dictate message (“I will be home at eight.”) 5.
Page 55 54 ALL ABOUT UCONNECT ACCESS Viewing Your Messages 1. Push the “Phone” button on the steering wheel. 2. Say “View message.” Press “View” on the in-vehicle touchscreen.
Page 56 Listening To A Message 1. Press “Listen” on the touchscreen or push the “Phone” button on the steering wheel and say “Listen,” the Uconnect system will read the received text message over the vehicle audio system. Barge-In Barge-in is a feature that enables a user to say a valid...
Page 57 Disclaimers Access. • Not all Voice Texting features may be available on your • Vehicle must be registered with an active Uconnect device. Access Advantage trial or paid subscription for free • Your MAP supported device must be paired and form text response to work.
Page 58 Only use available only on Uconnect 8.4A (sales code RA3) or Uconnect when it is safe to do so. Failure to do so Uconnect 8.4AN (sales code RA4) radios. Other FCA may result in an accident involving serious injury vehicles do support hands free texting, but only with or death.
Page 59 (SMS) sent to your device by voice while in your 4. Do I have to “train” my Uconnect radio to my voice? vehicle. FCA uses the latest voice recognition engine that 8.
Page 60: Remote Door Lock/Unlock
ALL ABOUT UCONNECT ACCESS 59 • Using the Uconnect Access App from a compatible 10. Can I use Text Messaging if the “messaging” button doesn’t turn white? Only MAP compatible devices device will work with Text Messaging. If your device is •...
Page 61 60 ALL ABOUT UCONNECT ACCESS 3. A pop-up screen will appear asking for your Uconnect Mopar Owner Connect website: Security PIN (this is the same 4-digit code established 1. Log on to the Mopar Owner Connect website when your registered your Uconnect Access system).
Page 62 2. For security purposes, the Uconnect Care agent will verify your identity by asking for your 4-digit 4. You will then be asked to enter your Uconnect Security Uconnect Security PIN. PIN (this is the same 4-digit code established when your registered your Uconnect Access system).
Page 63 (data) network connection. prove performance. • Vehicle must be registered with Uconnect Access and 2. Which is faster, my Key Fob or the Uconnect Access have an active subscription that includes the appli- App? Your Key Fob will lock/unlock the door quicker, cable feature or App.
Page 64: Remote Vehicle Start
ALL ABOUT UCONNECT ACCESS 63 3. Will my vehicle be safe if I lose my device? People 5. Why is the Uconnect Access App running slow? The sometimes lose their devices, which is why security Uconnect Access App relies on a mobile network...
Page 65 “cancel” button. has been remote started. After 15 minutes if you have not 3. A pop-up screen will appear asking for your Uconnect entered your vehicle with the key, the engine will shut off Security PIN (this is the same 4-digit code established automatically.
Page 66 (moparownerconnect.com) using the username and started press the “cancel” button. password you used when registering your Uconnect 4. You will then be asked to enter your Uconnect Security Access system. PIN (this is the same 4-digit code established when NOTE: If you forgot your username or password, links your registered your Uconnect Access system).
Page 67 All other Remote Services should be per- formed via the Mopar Owner Connect website 2. Which is faster, my Key Fob or the Uconnect Access (moparownerconnect.com) or through the Uconnect Ac- App? Your Key Fob will remote start your vehicle cess App on your compatible device.
Page 68: Remote Horn And Lights
ALL ABOUT UCONNECT ACCESS 67 3. Will my vehicle be safe if I lose my wireless device? 6. Why can’t all devices use the Uconnect Access App? People sometimes lose their wireless devices, which is The Uconnect Access App has been designed to work...
Page 69 • From Mopar Owner Connect website 4. The Uconnect Access App will confirm if your com- (moparownerconnect.com). mand was sent (or not). Press “OK” to close the pop-up screen. • Contacting Uconnect Care. 5. It will take a little while for the command to go If you want, you can set-up notifications for your account through to your vehicle.
Page 70 Fob if you are near the vehicle. 2. For security purposes, the Uconnect Care agent will 4. You will then be asked to enter your Uconnect Security verify your identity by asking for your 4-digit PIN (this is the same 4-digit code established when Uconnect Security PIN.
Page 71 “Panic” button. 2. Which is faster, my Key Fob or the Uconnect Access 5. Why can’t all devices use the Uconnect Access App? App? Your Key Fob will sound the horn and flash the The Uconnect Access App has been designed to work lights quicker;...
Page 72: Vehicle Health Alert
ALL ABOUT UCONNECT ACCESS 71 • Reduce the need to use your device to access Pandora Vehicle Health Alert so you can stay focused on driving. Your vehicle will send you an email alert if it senses a • Launch Pandora using Voice Recognition (VR) via a problem under the hood with one of your vehicles key systems.
Page 73 App. Check your device service • Customers can also create a new Pandora account by plan for more details. clicking on a link from the Uconnect Access Via Mobile profile page during registration and setup. Requirements • Vehicle must be properly equipped with the Uconnect Ensure that Via Mobile data has been turned on under “Settings”...
Page 74 ALL ABOUT UCONNECT ACCESS 73 • Vehicle must be registered with Uconnect Access and Uconnect Access App must be open and you must be have an active subscription that includes the appli- logged in. A blue light indicates that it’s providing cable feature or App.
Page 75 Pandora App on your device to use 6. Can I create a station from within the vehicle using Pandora Via Mobile. The Uconnect Access App is the vehicle touchscreen? Custom content can only be required, however.
Page 76 Ensure that Via Mobile data has been turned on under • Customers can also create a new iHeartRadio account “Settings” in the Uconnect Access App. by clicking on a link from the Uconnect Access Via Mobile profile page during registration and set-up.
Page 77 • To perform updates to this application, if required, Each time you want to use a Via Mobile App in your vehicle, the Uconnect Access App must be running on your vehicle must be connected to an operable 1X your device and the device must be paired via Bluetooth.
Page 78 Set the tuner to “Familiar,” “Mixed,” and “Less Famil- compatible device to the radio. The Uconnect Access iar” App must be open and you must be logged in. A blue –...
Page 79 8. Should I have the iHeartRadio App downloaded to 4. If I changed my password for iHeartRadio, do I have my device to use Uconnect Access Via Mobile? You to update it with Uconnect Access? Yes. Visit Mopar do not need to have the iHeartRadio App on your Owner Connect moparownerconnect.com, log in,...
Page 80 • Reduce the need to use your device to access Slacker 9. How do I know how much data is being used? Uconnect Access Via Mobile uses your device’s exist- Radio so you can stay focused on driving. ing data plan to stream content. Data usage varies by •...
Page 81 Each time you want to use a Via Mobile App in your ize your experience. Like a song? Heart it to hear it more vehicle, the Uconnect Access App must be running on often. Dislike a song? Ban it and the song or artist will be your device and the device must be paired via Bluetooth.
Page 82 • Vehicle must be registered with Uconnect Access and compatible device to the vehicle touchscreen. The have an active subscription that includes the appli- Uconnect Access App must be open and you must be cable feature or App. logged in. A blue light indicates that it’s providing data to the vehicle.
Page 83 5. Can I create a Slacker Radio account during station? As you listen to music, use the button on the Uconnect Access registration and set-up? There is a touchscreen to confirm your preference to the music link from the Via Mobile profile page where the currently being played.
Page 84 8. Should I have the Slacker Radio App downloaded to Description my device to use Uconnect Access Via Mobile? You Aha lets you easily access and organize your favorite web do not need to have the Slacker Radio App on your content on your device, then seamlessly integrates the device to use Slacker Radio Via Mobile.
Page 85 “Associate Accounts.” You can also associate your Aha account from aharadio.com. Each time you want to use a Via Mobile App in your vehicle, the Uconnect Access App must be running on your device and the device must be paired via Bluetooth.
Page 86 ALL ABOUT UCONNECT ACCESS 85 • Vehicle must be equipped with Uconnect 8.4A/8.4AN. Requirements • Vehicle must be properly equipped with the Uconnect Access System. FAQs • Your device must be compatible with the Uconnect 1. Why can’t I get Aha Via Mobile to work? Here are Access App and properly connected to the vehicle.
Page 87 Then, ensure you have properly connected your com- location. patible device to the vehicle touchscreen. The Uconnect Access App must be open. A blue light 4. How do I sync my Aha account with Facebook, indicates that it’s providing data to the vehicle.
Page 88: Maintain My Uconnect Access Account
12. How do I know how much data is being used? website. Uconnect Access Via Mobile uses your device’s exist- 9. Can I create an Aha account during Uconnect Access ing data plan to stream content. Data usage varies by registration and setup? There is a link from the Via phone/device, content (e.g.
Page 89: Adding Vehicles To My Uconnect Access Account
• Saturday and Sunday – 8:00 am to 4:00 pm a Vehicle. Connected vehicles must follow the secure registration process to be added to an account. 1. How Do I Register For My Uconnect Access Ac- count? Press the “Apps” button on the in-vehicle UCONNECT CARE & FAQs touchscreen, then select Uconnect Registration.
Page 90 ALL ABOUT UCONNECT ACCESS 89 3. How Do I Create A Uconnect Security PIN? Set up 5. How Do I Create A Uconnect Payment PIN? Log into your Uconnect Security PIN during the registration Mopar Owner Connect website process. The Uconnect Security PIN will be required to (moparownerconnect.com) with your username and...
Page 91 For more information please contact and select Edit Profile > Uconnect Payment Account. Uconnect Care at 855-792-4241. 9. How Do I Update My Uconnect Profile? Your name, 11. Can I Access Every App And Service While Driv- home address, phone number, email address and...
Page 92 Or Will It Automatically Renew? There is no PIN and complete the process. auto-renewal feature currently offered. You can find You can also go to the Uconnect Store online at Mopar the expiration dates for all of your App and package Owner Connect (moparownerconnect.com), select subscriptions from your in-vehicle touchscreen, se- the Shop tab, then Uconnect Store.
Page 93 20. Which Apps Are Included With My Vehicle? Go to 25. How Do I Re-Initiate A Download App If There Uconnect Store > My Apps to see Apps currently Was An Error? If you’re having issues with an App available on your vehicle.
Page 94 1X (voice/data) or privacy statement 3G (data) network. Other Uconnect services will only chrysler.com/universal/privacy.html. be operable if your Uconnect Access service is active and you are connected to an operable 1X (voice/data) or 3G (data) network.
Page 95: Safety Guidelines
ALWAYS obey traffic laws and pay attention to the • Ensure the volume level of the system is set to a level road. Some Uconnect Access services, including 9-1-1 that still allows you to hear outside traffic and emer- and Assist, will NOT work without an operable 1X gency vehicles.
Page 96 ALL ABOUT UCONNECT ACCESS 95 NOTE: Many features of this system are speed depen- isopropyl alcohol and water solution ratio of 50:50. Be dent. For your own safety, it is not possible to use some sure to follow the solvent manufacturer’s precautions of the touchscreen features while the vehicle is in motion.
Page 97 96 ALL ABOUT UCONNECT ACCESS Modifications not expressly approved by the radio Increase the separation between the equipment and manufacturer could void the user’s authority to operate receiver. the equipment. Consult the dealer or an experienced radio technician for help.
Page 98: Device Connection And Audio Tips With Uconnect
ALL ABOUT UCONNECT ACCESS 97 • Device calls will always have the highest priority energy emitted is far less than the electromagnetic energy emitted by wireless devices such as mobile devices. regardless of which connection is active (only the 9-1-1...
Page 99 98 ALL ABOUT UCONNECT ACCESS • Device calls will mute all audio except for NAV prompts if guidance is currently active (audio will resume after device call is ended). • All secondary incoming device calls will be treated similar to “call waiting” (except 9-1-1 Call).
Page 100 ▫ Setting Presets ..... . .106 UCONNECT PHONE ....125 ▫...
Page 101 100 UCONNECT 8.4A/8.4AN ▫ Things You Should Know About Your Uconnect SiriusXM TRAFFIC — U.S. MARKET 8.4AN Phone ......144 ONLY .
Page 102: Uconnect 8.4A/8.4An System
UCONNECT 8.4A/8.4AN 101 UCONNECT 8.4A/8.4AN SYSTEM 2. Media Press the “Media” button on the touchscreen to access media sources such as: Disc (If Equipped), USB Device, AUX, Bluetooth, and SD Card (If Equipped) as long as the requested media is present.
Page 103: Personalized Menu Bar
Uconnect Phone feature. PERSONALIZED MENU BAR 8. Enter/Browse & Tune/Scroll The Uconnect features and services in the main menu bar Push the ENTER/BROWSE button to accept a high- are easily changed for your convenience. Simply follow lighted selection on the screen. Rotate the TUNE/...
Page 104: Radio Mode
UCONNECT 8.4A/8.4AN 103 RADIO MODE Radio Controls The radio is equipped with the following modes: • AM • FM • SiriusXM Satellite Radio (if equipped) Press the RADIO button on the touchscreen, bottom left corner, to enter the Radio Mode. The different tuner modes;...
Page 105 The electronic volume control turns continuously (360 HD Radio (8.4AN Only) degrees) in either direction, without stopping. Turning HD Radio technology (available on Uconnect 8.4AN in the VOLUME/MUTE control knob clockwise increases the U.S. market) works similar to conventional radio the volume, and counterclockwise decreases it.
Page 106 UCONNECT 8.4A/8.4AN 105 station or channel. During a Seek Up function, if the Fast Seek Down radio reaches the starting station after passing through Press and hold the “Seek Down” button on the the entire band two times, the radio will stop at the touchscreen to advance the radio through the avail- station where it began.
Page 107: Setting Presets
106 UCONNECT 8.4A/8.4AN Undo When you are receiving a station that you wish to commit into memory, press and hold the desired num- You can backspace an entry by pressing the bottom left bered button on the touchscreen for more that two “Undo”...
Page 108: Siriusxm Satellite Radio Mode - If Equipped
UCONNECT 8.4A/8.4AN 107 Scrolling Preset List Return To Main Radio Screen Once in the Browse Presets screen, you can scroll the You can return to the Main Radio Screen, by pressing the preset list by rotation of the TUNE/SCROLL knob, or by “X”...
Page 109 108 UCONNECT 8.4A/8.4AN • On the go — With a SiriusXM Internet Radio subscrip- www.siriusxm.com. All fees and programming subject tion included with the All Access trial, you’ll get to change. Our satellite service is available only to those SiriusXM on your computer, smarthphone, or tablet.
Page 110 UCONNECT 8.4A/8.4AN 109 • The SiriusXM Presets are displayed at the top of the No Subscription screen. Radios equipped with a Satellite receiver, require a • The Genre is displayed below the Presets Bar. subscription to the SiriusXM Service. When the Radio does not have the necessary subscription, the Radio is •...
Page 111 110 UCONNECT 8.4A/8.4AN Replay Rewind The replay function provides a means to store and replay Press the “RW” button on the touchscreen to rewind the up to 22 minutes of music audio and 48 minutes of talk content in steps of five seconds. Pressing the “RW”...
Page 112 UCONNECT 8.4A/8.4AN 111 Live Fav. Artist: While the song is playing to set a Favorite Artist, press the “fav.” button on the touchscreen and Press the “Live” button on the touchscreen to resume then the Fav. Artist button on the touchscreen.
Page 113 112 UCONNECT 8.4A/8.4AN Browse In SXM Genre Press the “Browse” button on the touchscreen to edit Press the “Genre” button on the touchscreen to display a Presets, Favorites, Game Zone, and Jump settings, along list of Genres. You can select any desired Genre by with providing the SiriusXM Channel List.
Page 114 UCONNECT 8.4A/8.4AN 113 the TUNE/SCROLL knob to select the currently high- You can scroll the Favorites list by pressing the “Up and lighted Preset. When selected, the Radio tunes to the Down” arrows located at the right side of the screen.
Page 115: Audio
114 UCONNECT 8.4A/8.4AN Game Zone Remove Selection Press the “Game Zone” button, located at the left of the Press the “Remove Selection” tab at the top of the screen. Browse screen. This feature provides you with the ability Press the “Delete All” button on the touchscreen to delete to select teams, edit the selection, and set alerts.
Page 116 UCONNECT 8.4A/8.4AN 115 You can return to the Radio screen by pressing the “X” Pressing the “Front,” “Rear,” “Left,” or “Right” buttons located at the top right. or press and drag the blue Speaker Icon to adjust the Balance/Fade. Balance/Fade Equalizer Press the “Balance/Fade”...
Page 117 116 UCONNECT 8.4A/8.4AN Press the “+” or “–” buttons, or by pressing and dragging The Speed Adjusted Volume is adjusted by selecting from over the level bar for each of the equalizer bands. The “Off,” “1,” “2” or “3.” This alters the automatic adjust- level value, which spans between ±9, is displayed at the...
Page 118 UCONNECT 8.4A/8.4AN 117 Press the “AUX Volume Offset” button on the touch- screen to activate the AUX Volume Offset screen. The AUX Volume Offset is adjusted by pressing of the “+” and “–” buttons. This alters the AUX input audio volume.
Page 119: Media Mode
118 UCONNECT 8.4A/8.4AN MEDIA MODE Browse Press the “Browse” button on the touchscreen to display Disc Mode — If Equipped the browse window. The left side of the browse window Overview displays a list of ways you can browse through the Disc Mode is entered by either inserting a Disc or contents of the Disc.
Page 120: Usb/Ipod Mode
UCONNECT 8.4A/8.4AN 119 Repeat Tracks Press the “Repeat” button on the touchscreen to toggle Press the “trks” button on the touchscreen to display a the repeat functionality. The Repeat button on the touch- pop up with the Song List. The currently playing song is screen is highlighted when active.
Page 121 120 UCONNECT 8.4A/8.4AN Seek Up /Seek Down by pressing the “Up” and “Down” buttons to the right. The TUNE/SCROLL knob can also be used to scroll. Press and release the Seek Up button on the touch- screen for the next selection on the USB device/iPod.
Page 122: Aux Mode
UCONNECT 8.4A/8.4AN 121 Info AUX Mode Press the “Info” button on the touchscreen to display the Overview current track information. Press the “Info” button on the AUX (Auxiliary Mode) is entered by inserting an AUX touchscreen a second time to cancel this feature.
Page 123: Sd Card Mode - If Equipped
122 UCONNECT 8.4A/8.4AN NOTE: The vehicle radio unit is acting as the amplifier Seek Up /Seek Down for audio output from the Auxiliary device. Therefore if Press and release the Seek Up button on the touch- the volume control on the Auxiliary device is set too low, screen for the next selection on the SD Card.
Page 124 UCONNECT 8.4A/8.4AN 123 sub-functions, which can be scrolled by pressing the provide an interesting change of pace. Press the “Shuffle” “Up” and “Down” buttons to the right. The TUNE/ button on the touchscreen a second time to turn this SCROLL knob can also be used to scroll.
Page 125: Bluetooth Mode
Press and release the “Right Arrow” button on the Uconnect System. touchscreen for the next selection on the Bluetooth NOTE: See the pairing procedure in the Uconnect Phone device. Press and release the “Left Arrow” button section for more details.
Page 126: Uconnect Phone
Bluetooth device is within the Overview first second of the current selection. Uconnect Phone is a voice-activated, hands-free, in- Media Mode vehicle communications system. Uconnect Phone allows Press the “Media” button on the touchscreen to select the you to dial a phone number with your mobile phone.
Page 127 • Reviewing your recent Incoming SMS. Smith Mobile”). • Listen to Music on your Bluetooth Device via the • Voice Texting (Requires registration to Uconnect Ac- touchscreen. cess and a current subscription). • Pairing up to 10 phones/audio devices for easy access NOTE: Examples of Voice Commands are provided to connect to them quickly.
Page 128 UCONNECT 8.4A/8.4AN 127 For Uconnect customer support: WARNING! (Continued) • U.S. residents - visit UconnectPhone.com or call 877- Uconnect when it is safe to do so. Failure to do so 855-8400 may result in an accident involving serious injury or death.
Page 129: Operation
128 UCONNECT 8.4A/8.4AN Uconnect Phone Button The Uconnect Phone is fully integrated with the vehicle’s audio system. The volume of the Uconnect Phone can be The Uconnect Phone button on your steering wheel adjusted either from the radio volume control knob or...
Page 130 • For certain operations, compound commands can be Natural Speech used. For example, instead of saying “Call” and then Your Uconnect Phone Voice system uses a Natural Lan- “John Smith” and then “mobile”, the following com- guage Voice Recognition (VR) engine.
Page 131 Pair (Link) Uconnect Phone To A Mobile Phone If you need assistance at any prompt, or if you want to To begin using your Uconnect Phone, you must pair your know your options at any prompt, say “Help” following compatible Bluetooth enabled mobile phone. Mobile the beep.
Page 132 • You must have Bluetooth enabled on your phone to Bluetooth connections. complete this procedure. 5. If No is selected, and you still would like to pair a • The vehicle must be in PARK. mobile phone, press the “Settings” button from the Uconnect Phone main screen.
Page 133 Bluetooth audio device can be connected while the system is connecting. to the Uconnect system at a time. If “No” is selected, simply select “Uconnect” from the mobile phone/ 7. When your mobile phone finds the Uconnect system, audio device Bluetooth screen, and the Uconnect select “Uconnect.”...
Page 134 4. Search for available devices on your Bluetooth enabled the Phone main screen. mobile phone. When prompted on the phone, enter the name and PIN shown on the Uconnect screen. 2. Next, press the “Phone/Bluetooth” button on the touchscreen. 5. Uconnect Phone will display an in process screen...
Page 135 PIN shown on the Uconnect screen. You can also use the following VR commands to bring up 6. Uconnect Phone will display an in process screen the Paired Phone screen from any screen on the radio: while the system is connecting.
Page 136 Audio Device After Pairing 3. Press the “Settings” button located to the right of the Uconnect Phone will automatically connect to the highest device name. priority paired phone and/or Audio Device within range. If you need to choose a particular phone or Audio 4.
Page 137 Making A Phone Or Audio Device A Favorite phonebook. Specific Bluetooth Phones with Phone Book 1. Press the “Settings” button on the touchscreen. Access Profile may support this feature. See Uconnect website, UconnectPhone.com, for supported phones. 2. Press the “Paired Phones” or “Paired Audio Devices”...
Page 138 • To call a name from a downloaded mobile phone book, • This downloaded phonebook cannot be edited or follow the procedure in the “VOICE RECOGNITION deleted on the Uconnect Phone. These can only be QUICK TIPS” section. edited on the mobile phone. The changes are trans- ferred and updated to Uconnect Phone on the next •...
Page 139: Phone Call Features
The following features can be accessed through the appears, press “Add from Mobile.” You will then be Uconnect Phone if the feature(s) are available and sup- asked which contact and number to choose from your ported by Bluetooth on your mobile service plan. For mobile phonebook.
Page 140 2. After the “Listening” prompt and the following beep, say “Dial 151-123-4444.” • Dial by pressing in the number 3. The Uconnect Phone will dial the number 151-123- • Voice Commands (Dial by Saying a Name, Call by 4444. Saying a Phonebook Name, Redial or Call Back) Call By Saying A Phonebook Name •...
Page 141 140 UCONNECT 8.4A/8.4AN Call Controls Touch-Tone Number Entry The touchscreen allows you to control the following call 1. Press the “Phone” button on the touchscreen. features: 2. Press the “Dial” button on the touchscreen. • Answer 3. The Touch-Tone screen will be displayed.
Page 142 You may browse up to 31 of the most recent of each of the following call types: When you receive a call on your mobile phone, the Uconnect Phone will interrupt the vehicle audio system. • All Calls Push the Phone button on the steering wheel to •...
Page 143 142 UCONNECT 8.4A/8.4AN NOTE: The Uconnect Phone compatible phones in the Toggling Between Calls market today do not support rejecting an incoming call If two calls are in progress (one active and one on hold), when another call is in progress. Therefore, the user can press the “Swap”...
Page 144: Advanced Phone Connectivity
The Uconnect Phone allows ongoing calls to be trans- the following beep, say “Redial.” ferred from your mobile phone to the Uconnect Phone The Uconnect Phone will call the last number that was without terminating the call. To transfer an ongoing call dialed from your mobile phone.
Page 145: Things You Should Know About Your Uconnect
• Speak normally, without pausing, just as you would You have full responsibility and assume all risks speak to a person sitting a few feet/meters away from related to the use of the Uconnect features and you. applications in this vehicle. Only use Uconnect when •...
Page 146 Audio quality is maximized under: Voice Text Reply • Low-To-Medium Blower Setting Once your Uconnect system is paired with a compatible • Low-To-Medium Vehicle Speed mobile device, the system can announce a new incoming text message, and read it to you over the vehicle audio •...
Page 147 146 UCONNECT 8.4A/8.4AN Here’s how: Push the “Uconnect Phone” button “Yes.” “I’m on my “Are there wait for the beep, then say “reply.” Uconnect will give way.” yet?” the following prompt: “Please say the message you “No.” “I’ll be late.”...
Page 148 Only use Press the “Apps ” button on the touchscreen to Uconnect when it is safe to do so. Failure to do so begin the registration process. may result in an accident involving serious injury or death.
Page 149 2. Wait for the beep. your message will be truncated.” 3. Say “Text.” 8. Uconnect will then repeat the message back to you. 4. Uconnect will prompt you “Say the phone number, or 9. Uconnect will prompt you: To add to your message, full name and phone type of the contact you want to say “Continue”;...
Page 150 See recent text messages listed by number on Uconnect screen “Listen to/view (message number four, for example)” Hear messages or read it on Uconnect screen “Reply” Send a voice text reply to a current message “Forward text/message to John Smith”...
Page 151 Mobile phones have been found to lose connection to the This device complies with Part 15 of the FCC rules and Uconnect Phone. When this happens, the connection can RSS 210 of Industry Canada. Operation is subject to the generally be re-established by switching the mobile following conditions: phone OFF/ON.
Page 152: Navigation
UCONNECT 8.4A/8.4AN 151 • Press “Where To?” to find or route to a destination. NAVIGATION • Press “View Map” to view the map. Main Menu • Press “Information” to view Traffic, Where Am I? and To access the Navigation system, press the Nav button on the bottom of the touchscreen.
Page 153: Where To
152 UCONNECT 8.4A/8.4AN Where To? NOTE: Refer to the individual section of the chosen option for further information. Where To? — Main Menu Address Press this button on the touchscreen to search by a street address or a street name with house number.
Page 154 UCONNECT 8.4A/8.4AN 153 Favorites geography. You can determine a geo coordinate with the help of a handheld GPS receiver, a map, or the navigation Press this button on the touchscreen to access previously system. saved addresses or locations. Point on Map...
Page 155 154 UCONNECT 8.4A/8.4AN are driving. Select the option to stop trail recording to Where To? — Address end tracking. This gives you a point of reference to for a To enter a destination by Address, follow these steps: particular route if needed.
Page 156 UCONNECT 8.4A/8.4AN 155 2. Press “Enter City” or “Enter Street” to begin entering If you press “Enter Street,” you will have to enter and the address of your destination. select/press the desired street name in the correct city and then you will have to enter the house number.
Page 157 156 UCONNECT 8.4A/8.4AN Once the correct City, Street and Number has been If you are currently on a route guidance and you select entered, you will be asked to confirm your destination Recent, the system will ask you to choose one of the by pressing “OK.”...
Page 158 UCONNECT 8.4A/8.4AN 157 Where To? — Recent 2. Press the button on the touchscreen with the name of the desired destination. To route to a Recent destination, follow these steps: 1. While in the Nav Main Menu, press the “Where To?”...
Page 159 158 UCONNECT 8.4A/8.4AN To display the options for a destination press the “Options” button on the touchscreen that looks like a gear. • Edit Name • Add Phone Number • Move Up in the list The following Options are available for each destination: •...
Page 160 UCONNECT 8.4A/8.4AN 159 NOTE: You can press the “back arrow” button on the The Point of Interest database allows you to select a touchscreen to return to the previous screen or the “X” destination from a list of locations and public places, or button on the touchscreen to exit.
Page 161 160 UCONNECT 8.4A/8.4AN • Near Destination (only available during route guidance) • Along Route (only available during route guidance) You can also change your POI search area, by pressing the “Change Search Area” button on the touchscreen. You will have the following options to change your search area: NOTE: You can press the “back arrow”...
Page 162 UCONNECT 8.4A/8.4AN 161 POI — Gas Stations To select a Gas Station POI, follow these steps: 1. While in the Nav Main Menu, press the “Where To?” button on the touchscreen, then press the “Point of Interest” button on the touchscreen.
Page 163 162 UCONNECT 8.4A/8.4AN If you are currently on a route guidance and you select a gas station, the system will ask you to choose one of the following: • Cancel previous route • Add as first destination • Add as last destination NOTE: You can press the “back arrow”...
Page 164 UCONNECT 8.4A/8.4AN 163 POI — Restaurants To select a Restaurant POI, follow these steps: 1. While in the Nav Main Menu, press the “Where To?” button on the touchscreen, then press the “Point of Interest” button on the touchscreen. You can search for a restaurants by the following categories, which are button tabs at the top of the screen.
Page 165 164 UCONNECT 8.4A/8.4AN 3. Press the desired Restaurant and press “Yes” to con- 1. While in the Nav Main Menu, press the “Where To?” firm the destination. button on the touchscreen, press the “Point of Interest” button on the touchscreen.
Page 166 UCONNECT 8.4A/8.4AN 165 3. Press the desired hotel or motel and press “Yes” to confirm the destination. If you are currently on a route guidance and you select a Hotel or Motel, the system will ask you to choose one of the following: •...
Page 167 166 UCONNECT 8.4A/8.4AN POI — ATM/Banking To select a ATM or Bank POI, follow these steps: 1. While in the Nav Main Menu, press the “Where To?” button on the touchscreen, then press the “Point of Interest” button on the touchscreen.
Page 168 UCONNECT 8.4A/8.4AN 167 3. Press the desired ATM or Bank and press “Yes” to 1. While in the Nav Main Menu, press the “Where To?” confirm the destination. button on the touchscreen, then press the “Point of Interest” button on the touchscreen.
Page 169 168 UCONNECT 8.4A/8.4AN • Coffee Shops • Community • Entertainment • Gas Stations • Health and Beauty • Highway Exit • Hospital • Hotels/Motels • Other • Parking • Recreation You can search through the available POI categories to • Restaurants find your desired POI.
Page 170 UCONNECT 8.4A/8.4AN 169 If you are currently on a route guidance and you select a POI, the system will ask you to choose one of the following: • Cancel previous route • Add as first destination • Add as last destination NOTE: You can press the “back arrow”...
Page 171 170 UCONNECT 8.4A/8.4AN 2. Press the “Spell Name” button on the touchscreen. 3. A keyboard will appear on the screen. Type in the POI that you want to search and press the “List” button on the touchscreen to display available items.
Page 172 UCONNECT 8.4A/8.4AN 171 If you are currently on a route guidance and you select a POI, the system will ask you to choose one of the following: • Cancel previous route • Add as first destination • Add as last destination NOTE: You can press the “back arrow”...
Page 173 172 UCONNECT 8.4A/8.4AN 4. To save a favorite destination, press the “Add Favor- If you are currently on a route guidance and you select a ite” button on the touchscreen and follow the steps to Favorite, the system will ask you to choose one of the route a destination.
Page 174 UCONNECT 8.4A/8.4AN 173 Where To? — Intersection 2. Press the “Enter City” button, to enter the desired city name. To enter a destination by Intersection, follow these steps: NOTE: If the system automatically recognizes the city it 1. While in the Nav Main Menu, press the “Where To?”...
Page 175 174 UCONNECT 8.4A/8.4AN 3. Once the correct City has been selected, you will be NOTE: You can press the “back arrow” button on the asked to spell the desired street name, then enter the touchscreen to return to the previous screen or the “X”...
Page 176 UCONNECT 8.4A/8.4AN 175 NOTE: Refer to the individual section of the chosen option for further information. • Address • Recent • Point of Interest • Favorites • Intersection • GEO Coordinates • Point on Map • City Center • Closest Cities If there is no Home Address entered, press “Yes”...
Page 177 176 UCONNECT 8.4A/8.4AN 4. This address will be saved as your Home Address and Where To? — Trips it can be accessed by pressing the “Go Home” button To route to a saved Trip, follow these steps: in the Where To? Menu.
Page 178 UCONNECT 8.4A/8.4AN 177 To add a Trip, follow these steps: 1. Press the “Create new Trip” button on the touchscreen. 2. Type in the new Trip Name. 3. Press “Add Destination” to add destinations to your trip. 4. Choose from the following options to add a destina- tion •...
Page 179 178 UCONNECT 8.4A/8.4AN • Phone Number The following Options are available for each trip: • Edit Name NOTE: Refer to the individual section of the chosen option for further information. • Move Up in the list 5. Add more needed destinations to your trip.
Page 180 UCONNECT 8.4A/8.4AN 179 2. Enter the Latitude by typing in the numbers. Use the Press the “Format” button on the touchscreen to left and right arrows to select specific numbers in the change the format of the Latitude/Longitude entry. location shown.
Page 181 180 UCONNECT 8.4A/8.4AN 5. Press “OK” to confirm the destination. 1. While in the Nav Main Menu, press the “Where To?” button on the touchscreen then press the “Point on 6. Press the “Yes” button on the touchscreen to confirm Map”...
Page 182 UCONNECT 8.4A/8.4AN 181 4. Press the “Yes” button on the touchscreen to confirm your destination and begin your route. If you are currently on a route guidance and you select a Point on Map, the system will ask you to choose one of the following: •...
Page 183 182 UCONNECT 8.4A/8.4AN Where To? — City Center To enter a destination by City Center, follow these steps: 1. While in the Nav Main Menu, press the “Where To?” button on the touchscreen then press the “City Center” button on the touchscreen.
Page 184 UCONNECT 8.4A/8.4AN 183 If you are currently on a route guidance and you select a City Center, the system will ask you to choose one of the following: • Cancel previous route • Add as first destination • Add as last destination NOTE: You can press the “back arrow”...
Page 185 184 UCONNECT 8.4A/8.4AN • Cancel previous route • Add as first destination • Add as last destination NOTE: You can press the “back arrow” button on the touchscreen to return to the previous screen or the “X” button on the touchscreen to exit.
Page 186 UCONNECT 8.4A/8.4AN 185 2. Press “Start Trail Recording.” 3. When you want to end the recording of a route, press “Stop Trail Recording.” The trip you recorded will be added to the Recent Trails list.
Page 187 186 UCONNECT 8.4A/8.4AN Where To? — Phone 2. Enter the Phone Number of the destination you would like to route to. To enter a destination by Phone number, follow these steps: 3. Press the desired destination from the list. 1. While in the Nav Main Menu, press the “Where To?”...
Page 188 UCONNECT 8.4A/8.4AN 187 Before Route Guidance Before confirming the route with the “Yes” button on the touchscreen, it is possible to select options different from the default route settings. • Options – Press the “Options” button on the touch- screen to display a list of options to alter your route. To make a selection press and release the desired setting until a check-mark appears.
Page 189 188 UCONNECT 8.4A/8.4AN • Avoid – Press the “Avoid” button on the touchscreen to choose road types to avoid during your route. To make a selection press and release the desired setting until a check-mark appears.
Page 190: View Map
UCONNECT 8.4A/8.4AN 189 • Save – Press the “Save” button on the touchscreen to save the destination as a Favorite. Press the “Yes” button on the touchscreen to confirm your destination and to start your route guidance. NOTE: You can press the “back arrow” button on the touchscreen to return to the previous screen or the “X”...
Page 191 190 UCONNECT 8.4A/8.4AN Zoom In +/Zoom Out – Press the “Zoom In (+) or Zoom Out (–)” buttons on the touchscreen to change the zoom level. Roads with lower functional classification are not shown in higher zoom levels. (e.g. residential streets, lightly-traveled county roads.)
Page 192 UCONNECT 8.4A/8.4AN 191 • Settings Turn List (only during route guidance) Press the area in the upper center part of the screen that Press this button on the touchscreen to view all the displays your next turn to see a Turn List for your current available settings.
Page 193 192 UCONNECT 8.4A/8.4AN Where Am I? Press the area in the lower center part of the screen that displays your current location to view the Where Am I? view. Where Am I? displays the address and GEO Coordinates of your current location.
Page 194 UCONNECT 8.4A/8.4AN 193 View Map — Settings With the Map displayed, press the “Options” button on the touchscreen then press the “Settings” button on the touchscreen. The following Map Settings are available: • Map Setup — Press this button on the touchscreen to display items to customize how your map is viewed.
Page 195 194 UCONNECT 8.4A/8.4AN • Speed Limit — Press this button on the touchscreen to • GPS (DMS) — Press this button on the touchscreen to turn on/off speed limit warning announcements and change the GPS display. Press the desired button on to enter a pre-defined speed limit for your route.
Page 196 UCONNECT 8.4A/8.4AN 195 Settings — Map Setup With the Map displayed, press the “Options” button on the touchscreen, then press the “Settings” button on the touchscreen and then the “Map Setup” button on the touchscreen. The following Map Setup options are available:...
Page 197 196 UCONNECT 8.4A/8.4AN • 3D (3D Map View Is Only Available On Uconnect Destination Information 8.4AN. Must Select 3D City Models Or 3D Landmarks Press this button on the touchscreen to change the For 3D Map View To Display.) Destination Information that is displayed in the upper •...
Page 198 UCONNECT 8.4A/8.4AN 197 • Near while in Map View. Press and release the desired selec- tion button on the touchscreen until a check-mark ap- • Off pears, showing the setting has been selected. Vehicle Icon TMC Incidents – If Equipped...
Page 199 198 UCONNECT 8.4A/8.4AN 3D City Models (Available On The Uconnect 8.4AN) Park Areas Press this button on the touchscreen to display 3D city Press this button on the touchscreen to display Park models while in Map View. Press and release the button Areas while in Map View.
Page 200 UCONNECT 8.4A/8.4AN 199 River Names The following Guidance options are available. • Play Voice Guidance Prompts Press this button on the touchscreen to display River Names while in Map View. Press and release the button Press this button on the touchscreen to enable Voice on the touchscreen until a check-mark appears, showing Guidance Prompts during route guidance.
Page 201 200 UCONNECT 8.4A/8.4AN • Junction View – Manual – Off Press this button on the touchscreen to enable Junction • TMC Avoidance Types (If Equipped) View during route guidance. Press and release the button on the touchscreen until a check-mark appears, showing Press this button on the touchscreen to display the the setting has been selected.
Page 202: Information
UCONNECT 8.4A/8.4AN 201 Information From the Nav Main Menu, press the “Information” button on the touchscreen and select one of the following options to view additional information. • Traffic • Where Am I? • Trip Computer Information — SiriusXM Traffic (U.S. MARKET 8.4AN ONLY)
Page 203 202 UCONNECT 8.4A/8.4AN 2. Press the “Where Am I?” button on the touchscreen. Traffic displays detailed traffic information, refer to SiriusXM Traffic in this section for further information. Where Am I? displays the address and GEO Coordi- nates of your current location.
Page 204 UCONNECT 8.4A/8.4AN 203 4. Press the “Save” button on the touchscreen to save the location in your Favorites. NOTE: You can press the “back arrow” button on the touchscreen to return to the previous screen or the “X” button on the touchscreen to exit.
Page 205: Emergency
204 UCONNECT 8.4A/8.4AN • Moving average speed • Police – Search and route to a Police Station close to • Maximum speed reached your current location • Total time traveled • Fire Department – Search and route a Fire Department •...
Page 206 UCONNECT 8.4A/8.4AN 205 Press the “Save” button on the touchscreen to save your current location in Favorites. NOTE: You can press the “back arrow” button on the touchscreen to return to the previous screen or the “X” button on the touchscreen to exit.
Page 207 206 UCONNECT 8.4A/8.4AN NOTE: In case of emergency, please contact the facility to verify their availability before proceeding. 3. Press the desired Hospital and press “Yes” to confirm the destination. If you are currently on a route guidance and you select a...
Page 208 UCONNECT 8.4A/8.4AN 207 Emergency — Police To search for a Police Station close to your current location, follow these steps: 1. While in the Nav Main Menu, press the “Emergency” button on the touchscreen. You can search for a Police Station by the following categories, which are button tabs at the top of the screen.
Page 209 208 UCONNECT 8.4A/8.4AN NOTE: In case of emergency, please contact the facility to Emergency — Fire Department verify their availability before proceeding. To search for a Fire Department close to your current location, follow these steps: 3. Press the desired Police Station and press “Yes” to confirm the destination.
Page 210 UCONNECT 8.4A/8.4AN 209 • Distance 2. Press the “Fire Department” button on the touch- screen. • ABC (Search) NOTE: In case of emergency, please contact the facility to verify their availability before proceeding. 3. Press the desired Fire Department and press “Yes” to confirm the destination.
Page 211: Map Updates
210 UCONNECT 8.4A/8.4AN Map Updates 3. Or, if you wish, you can also visit your dealer or place a phone call to request your Map Update. US/CAN The map data available in your vehicle is the most General Consumer Support 888-628-6277, FCA US...
Page 212: Siriusxm Travel Link - U.s. Market Only (8.4An Only)
UCONNECT 8.4A/8.4AN 211 • Fuel Prices — Check local gas and diesel prices in your 2. Traffic information from multiple sources, including police and emergency services, cameras and road area and route to the station of your choice. sensors. • Sports Scores — In-game and final scores as well as 3.
Page 213: Security Features
212 UCONNECT 8.4A/8.4AN NOTE: To provide Uconnect Services to you, we may record and monitor your conversations with Roadside Assistance, • SiriusXM Travel Link requires a subscription, sold Uconnect Care or Vehicle Care, whether such conversa- separately after the five year trial subscription in- tions are initiated through the Uconnect Services in your cluded with your vehicle purchase.
Page 214 ALWAYS obey traffic laws and pay attention to the 3. Once a connection between the vehicle and a 9-1-1 road. Some Uconnect Access services, including 9-1-1 operator is made, the 9-1-1 Call system may transmit and Assist, will NOT work without an operable 1X the following important vehicle information to a 9-1-1 (voice/data) or 3G (data) network connection.
Page 215 214 UCONNECT 8.4A/8.4AN NOTE: WARNING! • Your vehicle may be transmitting data as authorized • If anyone in the vehicle could be in danger (e.g., by the subscriber. fire or smoke is visible, dangerous road conditions • Once a connection is made between the vehicle’s...
Page 216 TERY POWER FOR ANY REASON (INCLUDING DURING OR AFTER AN ACCIDENT), THE If the 9-1-1 Call system detects a malfunction, any of the UCONNECT FEATURES, APPS AND SERVICES, following may occur at the time the malfunction is AMONG OTHERS, WILL NOT OPERATE.
Page 217 216 UCONNECT 8.4A/8.4AN • The Phone Screen will display the following message Even if the 9-1-1 Call system is fully functional, factors “Vehicle phone requires service. Please contact your beyond FCA US LLC’s control may prevent or stop 9-1-1 dealer.”...
Page 218 ALWAYS obey traffic laws and pay attention to the Operation is subject to the following two conditions: (1) road. Some Uconnect Access services, including 9-1-1 This device may not cause harmful interference, and (2) and Assist, will NOT work without an operable 1X this device must accept any interference received, includ- (voice/data) or 3G (data) network connection.
Page 219: Remote Service Features
218 UCONNECT 8.4A/8.4AN REMOTE SERVICE FEATURES If your vehicle is equipped with Remote Service Features, for more information, refer to moparownerconnect.com or call 855-792-4241for U.S. residents and 855-209-8317for Canadian residents.
Page 220 CUSTOMER PROGRAMMABLE FEATURES . . .221 ▫ Uconnect 8.4 Settings ....221 ▫ Auto Comfort Systems — If Equipped ..240 ▫...
Page 221 220 UCONNECT SETTINGS ▫ Clear Personal Data ....247 ▫ System Information ....247 PERFORMANCE CONTROL/PAGES AND DRIVE MODES .
Page 222: Customer Programmable Features
” button on the touchscreen to available settings. display the menu setting screen. In this mode, the Display Uconnect system allows you to access all of your programmable features. After pressing the “Display” button on the touchscreen the following settings will be available: NOTE: •...
Page 223 222 UCONNECT SETTINGS • Display Brightness With Headlights ON NOTE: To make changes to the Display Brightness with Headlights OFF setting, the headlights must be off and When in this display, you may select the brightness with the interior dimmer switch must not be in the party or the headlights on.
Page 224 UCONNECT SETTINGS 223 • Units Time-Out button on the touchscreen until a check-mark appears next to the setting, showing that setting has been When in this display, the odometer, and navigation selected. system (if equipped) may be changed between US and •...
Page 225: Units
224 UCONNECT SETTINGS • Pressure Units After pressing the “Units” button on the touchscreen you Select from: “psi,” “kPa,” or “bar.” may select each unit of measure independently displayed • Temperature in the Driver Information Display (DID), and navigation system (if equipped). The following selectable units of Select from: “°C,”...
Page 226: Voice
UCONNECT SETTINGS 225 Voice Clock After pressing the “Voice” button on the touchscreen the After pressing the “Clock” button on the touchscreen the following settings will be available: following settings will be available: • Voice Response Length • Sync Time With GPS...
Page 227: Safety & Driving Assistance
226 UCONNECT SETTINGS • Set Time Minutes • Set Date In Cluster — If Equipped This feature will allow you to adjust the minutes. The This feature will allow you to manually set the date in the “Sync time with GPS” button on the touchscreen must be cluster, select from the following fields: •...
Page 228 UCONNECT SETTINGS 227 Near. The default status of FCW is the Far setting. This of you. This allows for a more dynamic driving experi- means the system will warn you of a possible collision ence. To change the FCW status, press and release the with the vehicle in front of you when you are farther OFF, Near or Far button.
Page 229 The Front ParkSense Chime Volume settings can be steering wheel feedback for potential lane departures. selected from the DID or Uconnect System. The chime The amount of directional torque the steering system can volume settings include LOW, MEDIUM, and HIGH. The apply to the steering wheel to correct for vehicle lane factory default volume setting is MEDIUM.
Page 230 UCONNECT SETTINGS 229 your selection, press the “Rear ParkSense Vol.” button on Mirrors in Reverse” button on the touchscreen, until a the touchscreen, until a check-mark appears next to check-mark appears next to setting, indicating that the setting, indicating that the setting had been selected.
Page 231 230 UCONNECT SETTINGS Press the “Comfort” button on the touchscreen to provide signal is on. When “Off” is selected, the Blind Spot a balance of steering feel and steering effort. Monitor (BSM) system is deactivated. To change the Blind Spot Alert status, press the “Off,” “Lights” or •...
Page 232 UCONNECT SETTINGS 231 • Surround View Camera vehicle speed exceeds 8 mph (12 km/h), at which point it will immediately cancel and return to the last viewed Displays a complete 360 degree view of the vehicle’s screen. exterior environment while backing up. When this fea- •...
Page 233 232 UCONNECT SETTINGS • Active ParkView Backup Camera Guidelines on the touchscreen, until a check-mark appears next to setting, indicating that the setting had been selected. Your vehicle may be equipped with the ParkView Rear • ParkView Backup Camera Delay...
Page 234: Brakes
UCONNECT SETTINGS 233 The image will be displayed on the radio touchscreen System” in “Starting And Operating” for system function display along with a caution note to “check entire sur- and operating information. To make your selection, press roundings” across the top of the screen. After five sec- the “Hill Start Assist”...
Page 235: Lights
234 UCONNECT SETTINGS • Auto Park Brake interior ambient lighting, press the “+” or “-” button on the touchscreen to select your desired level. Auto Park Brake will set the park brake once the vehicle • Headlight Off Delay is set in park (or at key off for a manual transmission).
Page 236 UCONNECT SETTINGS 235 • Headlights With Wipers — If Equipped • Daytime Running Lights — If Equipped When this feature is selected, and the headlight switch is When this feature is selected, the headlights will turn on in the AUTO position, the headlights will turn on ap- whenever the engine is running.
Page 237: Doors & Locks
236 UCONNECT SETTINGS • Auto Door Locks passive entry feature. This feature may be selected with or without the sound horn on lock feature selected. To When this feature is selected, all doors will lock when the make your selection, press the “Flash Lights with Lock”...
Page 238 UCONNECT SETTINGS 237 Keyless Entry (RKE) transmitter, or when using the press the “Sound Horn with Remote Start” button on the passive entry feature. This feature may be selected with touchscreen until a check-mark appears next to setting, or without the sound horn on lock feature selected. To showing that setting has been selected.
Page 239 238 UCONNECT SETTINGS NOTE: If the vehicle is programmed 1st Press Of Key Fob setting, showing that the setting has been selected. Press Unlocks “All Doors,” all doors will unlock no matter the back arrow button on the touchscreen to return to the which Passive Entry equipped door handle is grasped.
Page 240 UCONNECT SETTINGS 239 • Flash Lights With Sliding Door NOTE: The seat will return to the memorized seat location (if Recall Memory with Remote Key Unlock is set When this feature is selected, the headlights flash when to ON) when the Remote Keyless Entry (RKE) transmitter the sliding door is opening.
Page 241: Auto Comfort Systems - If Equipped
When this feature is selected, the power window temperatures are below 40° F (4.4° C). When tempera- switches, radio, Uconnect Phone system (if equipped), tures are above 80° F (26.7° C) the driver vented seat will DVD video system (if equipped), power sunroof (if turn ON.
Page 242: Air Suspension - If Equipped
UCONNECT SETTINGS 241 button on the touchscreen to select your desired time Air Suspension — If Equipped interval, and choose from “0 seconds,” “45 seconds,” “5 After pressing the “Suspension” button on the touch- minutes” or “10 minutes.” screen the following settings will be available.
Page 243 242 UCONNECT SETTINGS system has been activated or the check-mark is removed appears next to the feature showing the system has been showing the system has been deactivated. activated or the check-mark is removed showing the system has been deactivated.
Page 244: Trailer Brake
UCONNECT SETTINGS 243 • Wheel Alignment Mode • Trailer Brake Type Before performing a wheel alignment this mode must be When this feature is selected, the Trailer Brake Type can enabled. Refer to your authorized dealer for further be changed between “Light Electric,” “Heavy Electric,”...
Page 245: Phone/Bluetooth
244 UCONNECT SETTINGS • Equalizer • AUX Volume Offset — If Equipped This feature allows you to adjust the Bass, Mid and Treble This feature provides the ability to tune the audio level settings. Adjust the settings with the “+” and “–” setting for portable devices connected through the AUX input.
Page 246: Siriusxm Setup - If Equipped
UCONNECT SETTINGS 245 • Do Not Disturb (key pad is not available while vehicle is in motion). Press the “OK” button on the touchscreen to return to After pressing the “Do Not Disturb” button on the the previous menu. touchscreen the following settings will be available: •...
Page 247 246 UCONNECT SETTINGS • Channel Skip services, it will be necessary to access the information on the Subscription Information screen to re-subscribe. SiriusXM can be programmed to designate a group of channels that are the most desirable to listen to or to Press the “Subscription Info”...
Page 248: Restore Settings
UCONNECT SETTINGS 247 • Clear Personal Data Restore Settings After pressing the “Restore Settings” button on the When this feature is selected it will remove personal data touchscreen the following settings will be available: including Bluetooth devices and presets. To remove personal information, press the “Clear Personal Data”...
Page 249 248 UCONNECT SETTINGS PERFORMANCE CONTROL/PAGES AND DRIVE MODES Your vehicle may be equipped with Performance Con- trol, Performance Pages and Drive Mode features. These features give the driver control over the systems in the vehicle which affect its performance, enabling the driver to tune it for desired driving scenarios.
Page 250 QUICK TIPS ......250 ▫ Uconnect Access ..... .258 ▫...
Page 251: Uconnect 8.4A/8.4An Voice Recognition Quick Tips
It provides the key Voice Commands and All you need to control your Uconnect system with your tips you need to know to control your Uconnect 8.4A or voice are the buttons on your steering wheel. 8.4AN systems.
Page 252 VOICE RECOGNITION QUICK TIPS 3. Speak clearly at a normal pace and volume while facing straight ahead. The microphone is positioned on the rearview mirror and aimed at the driver. 4. Each time you give a Voice Command, you must first push either the VR or Phone button, wait until after the beep, then say your Voice Command.
Page 253: Basic Voice Commands
252 VOICE RECOGNITION QUICK TIPS Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, say • Cancel to stop a current voice session •...
Page 254: Media
VOICE RECOGNITION QUICK TIPS • Tune to Satellite Channel Hits 1 Media Uconnect offers connections via USB, SD, Bluetooth and TIP: At any time, if you are not sure of what to say or auxiliary ports. Voice operation is only available for want to learn a Voice Command, push the VR button and connected USB and iPod devices.
Page 255: Phone
USB device. Your Voice Making and answering hands-free phone calls is easy Command must match exactly how the artist, album, with Uconnect. When the “phonebook” button is illumi- song and genre information is displayed. nated on your touchscreen, your system is ready. Check UconnectPhone.com for mobile phone compatibility...
Page 256: Voice Text Reply
1. Once an incoming text message is read to you, push the Phone button . After the beep, say: “Reply.” 2. Listen to the Uconnect prompts. After the beep, repeat one of the pre-defined messages and follow the system prompts.
Page 257 256 VOICE RECOGNITION QUICK TIPS PRE-DEFINED VOICE TEXT REPLY RESPONSES Okay. Where are you? I will be <num- ber> minutes Are you there Call me. late. yet? I’ll call you I need See you in later. directions. <number> min- utes. I’m on my way.
Page 258: Climate
VOICE RECOGNITION QUICK TIPS TIP: Voice Text Reply is not compatible with iPhone, but TIP: Voice Command for Climate may only be used to if your vehicle is equipped with Siri Eyes Free, you can adjust the interior temperature of your vehicle. Voice use your voice to send a text message.
Page 259: Navigation
258 VOICE RECOGNITION QUICK TIPS Navigation The Uconnect navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. (Navigation is optional on the Uconnect 8.4A system. See your dealer to activate navigation at any time.)
Page 260 Yelp Search An included trial and/or subscription is required to take Voice Texting advantage of the Uconnect Access services in the next Roadside Assistance Call section of this guide. To register with Uconnect Access, Wi-Fi Hotspot*** press the Apps button on the 8.4-inch touchscreen to get...
Page 261: Register
260 VOICE RECOGNITION QUICK TIPS Register 2. Press the “Uconnect Care” button on the touchscreen. To unlock the full potential of Uconnect Access in your 3. A helpful Uconnect Care Agent will register your vehicle, you first need to register with Uconnect Access.
Page 262 Link. 5. Next time you’re in your vehicle, enable Bluetooth, pair your phone and select the Via Mobile app you want to play from the Uconnect touchscreen to stream your personalized music. NOTE: • You can also complete this process on the web. Simply visit moparownerconnect.com log in and click Set Up...
Page 263: Voice Texting
262 VOICE RECOGNITION QUICK TIPS Voice Texting You must be registered with Uconnect Access and have a compatible MAP – enabled smartphone to use your voice 1. To send a message, push the Phone button . After to send a personalized text message. For details about the beep, say the following command: “Send mes-...
Page 264: Yelp
• Messages are limited to 140 characters. • The Messaging button on the touchscreen must be illuminated to use the feature. Yelp Once registered with Uconnect Access, you can use your voice to search for the most popular places or things iPhone Notification Setting around you.
Page 265 , then say: “YELP search.” 4. Listen to the system prompts and after the beep, tell Uconnect the place or business that you’d like Uconnect to find. TIP: Once you perform a search, you can reorganize the results by selecting either the Best Match, Rating or...
Page 266: Siriusxm Travel Link
5 - day weather forecast? SiriusXM Travel Link is a suite of services that brings a wealth of information right to your Uconnect 8.4AN system. (Not available for 8.4A system.) Push the VR button .
Page 267: Do Not Disturb
266 VOICE RECOGNITION QUICK TIPS Do Not Disturb While in Do Not Disturb, Conference Call can be selected so you can still place a second call without being inter- With Do Not Disturb, you can disable notifications from rupted by incoming calls. incoming calls and texts, allowing you to keep your eyes on the road and hands on the wheel.
Page 268: Additional Information
Sun., Closed Additional Information Uconnect Access Services Support 1-855-792-4241 Please have your Uconnect Security PIN ready when you call. © 2015 FCA US LLC. All rights reserved. Mopar and Uconnect are registered trademarks and Mopar Owner Connect is a trademark of FCA US LLC. Android is a trademark of Google Inc.
Page 269 Printed in the USA ©2015 FCA US LLC. All Rights Reserved. Chrysler, Dodge, Jeep, Ram, Mopar and Uconnect are trademarks of FCA US LLC. FIAT is a registered trademark of FCA Group Marketing S.p.A., used under license by FCA US LLC.

This manual is also suitable for:

8.4

Uconnect 8.4 NAV Supplemental Owner's Manual

All about Uconnect Access

Uconnect 8.4A/8.4An

Uconnect Settings

Voice Recognition Quick Tips

Quick Links

Chapters

Need help?

Questions and answers

Related Manuals for Uconnect 8.4 NAV

Summary of Contents for Uconnect 8.4 NAV

This manual is also suitable for:

Table of Contents