Table of Contents
Advertisement
Contents
Contents
1
1.1
We Want You to Be a Satisfied Customer ..................................1-1
CE Marking (Declaration of Conformity) .........................................1-1
1.2
SAFETY INFORMATION................................................................1-2
Warning and Precaution Symbols...................................................1-2
Meaning of Symbols........................................................................1-2
WARNING.......................................................................................1-3
CAUTION ........................................................................................1-4
Precautions for Routine Use ...........................................................1-5
1.3
Safety Information.........................................................................1-6
Laser Safety ....................................................................................1-6
Internal Laser Radiation ..................................................................1-6
CDRH Regulation............................................................................1-7
For European Users........................................................................1-8
For Denmark Users.........................................................................1-8
For Finland, Sweden Users.............................................................1-8
For Norway Users ...........................................................................1-9
Laser Safety Label ..........................................................................1-9
LED Radiation Safety....................................................................1-10
Ozone Release .............................................................................1-10
Acoustic Noise ..............................................................................1-10
1.4
About the User Manual ...............................................................1-11
Explanation of Manual Conventions..............................................1-11
[ ] key.............................................................................................1-11
1.5
Explanation of Basic Concepts and Symbols ..........................1-12
Paper Feeding...............................................................................1-12
Paper Orientation ..........................................................................1-13
2
2.1
Installation Precautions................................................................2-1
Installation site ................................................................................2-1
Power source ..................................................................................2-1
Space Requirements.......................................................................2-2
2.2
Operation Precautions..................................................................2-3
Operating Environment ...................................................................2-3
Proper Use ......................................................................................2-3
Di152/Di183
i
Advertisement
Table of Contents
Related Manuals for Konica Minolta DI183
Summary of Contents for Konica Minolta DI183
-
Page 1: Table Of Contents
Explanation of Manual Conventions..........1-11 [ ] key.....................1-11 Explanation of Basic Concepts and Symbols ......1-12 Paper Feeding................1-12 “Width” and “Length” ..............1-13 Paper Orientation ................1-13 Precautions Installation Precautions..............2-1 Installation site ................2-1 Power source ..................2-1 Space Requirements...............2-2 Operation Precautions..............2-3 Operating Environment ..............2-3 Proper Use ..................2-3 Di152/Di183... - Page 2 Two Ways of Loading the Original..........4-1 Specific Types of Originals ............. 4-1 Loading Originals in the Automatic Document Feeder .... 4-2 Precautions for Using the Automatic Document Feeder ....4-2 Mixed Originals................4-4 Place the Original on the Original Glass ........4-6 Di152/Di183...
- Page 3 Using the Utility Mode User’s Choice ................7-2 Mixed Orig..................7-6 Paper Priority ..................7-6 Copy Priority..................7-6 Density Priority ................7-6 Exposure Level Priority (Auto) ............7-6 Exposure Level Priority (Manual) ............7-7 Output Priority .................7-7 Crisscross Mode ................7-7 4in1 Copy Order................7-7 Book Binding Position ..............7-7 Di152/Di183...
- Page 4 Clearing a Paper Misfeed ............. 8-12 Troubleshooting Tips When This Type of Copy is Produced ........9-1 When the Copier is not Operating Correctly......9-4 10 Appendix 10.1 Specifications ................10-1 Copier Di152/Di183 ..............10-1 Automatic Document Feeder AF-10 ..........10-3 Di152/Di183...
- Page 5 Multiple Bypass Tray MB-5 ............10-4 10.2 Care of the Copier ...............10-5 Cleaning ..................10-5 10.3 Function Combination Table............10-6 Function Combination Table ............10-6 Conditions for Combined Functions..........10-6 10.4 List of Paper Sizes and Zoom Ratios ........10-7 Paper Sizes...................10-7 Zoom Ratios(Original Size to Paper Size) ........10-8 Di152/Di183...
- Page 6 Contents Di152/Di183...
-
Page 7: Introduction
Thank you for choosing a Minolta Di152/Di183. This User Manual describes the functions, operating procedures, precautions, and basic troubleshooting for the Di152/Di183 copier. Before using this copier, be sure to read the User Manual thoroughly in order to ensure that you use the copier efficiently. After you have gone through the manual, store it in the holder on the rear side of the copier and keep it handy at all times. -
Page 8: Safety Information
This symbol warns against possible electrical shock. A diagonal line indicates a prohibited course of action. This symbol warns against dismantling the device. A black circle indicates an imperative course of action. This symbol indicates you must unplug the device. Di152/Di183... -
Page 9: Warning
Do not throw the toner cartridge or toner into an open flame. The hot toner may scatter and cause burns or other damage. Connect the power cord only to an electrical outlet that is equipped with a grounding terminal. Di152/Di183... -
Page 10: Caution
Dust that accumulates between the plug terminals could cause a fire. • When unplugging the power cord, be sure to hold onto the plug. Pulling on the power cord could damage the cord, resulting in fire or electrical shock. Di152/Di183... -
Page 11: Precautions For Routine Use
Do not touch or scratch the surface of the toner unit developing roller or the PC drum, as poor image quality could result. Use the supplies and consumables recommended by the dealer. Use of any supply or consumable not recommended could result in poor image quality or breakdown. Di152/Di183... -
Page 12: Safety Information
The laser diode and the scanning polygon mirror are incorporated in the print head unit. The print head unit is NOT A FIELD SERVICE ITEM: Therefore, the print head unit should not be opened under any circumstances. Print Head Di152/Di183... -
Page 13: Cdrh Regulation
Use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. This is a semiconductor laser. The maximum power of the laser diode is 5 mW and the wavelength is 770-795 nm. Di152/Di183... -
Page 14: For European Users
Det här är en halvledarlaser. Den maximala effekten för laserdioden är 5mW och våglängden är 770-795nm. VARO! Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättömälle la- sersäteilylle. Älä katso säteeseen. VARNING! Osynlig laserstrålning när denna del är öppnad och spärren är urkopp- lad. Betrakta ej strålen. Di152/Di183... -
Page 15: For Norway Users
Dette en halvleder laser. Maksimal effekt till laserdiode er 5mW og bølge- lengde er 770-795nm. Laser Safety Label A laser safety label is attached to the outside of the machine as shown be- low. For Europe CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUCT For United States Di152/Di183... -
Page 16: Led Radiation Safety
Acoustic Noise For European Users Machine Noise Regulation 3 GSGV, 18.01.1991 : The sound pressure lev- el at the operator position according to EN 27779 is equal to or less than 70dB(A). 1-10 Di152/Di183... -
Page 17: About The User Manual
Text formatted in this style pro- vides additional assistance. ➜ Text formatted in this style describes the action that will ensure the desired results are achieved. [ ] key The names of keys on the control panel are written as shown above. Di152/Di183 1-11... -
Page 18: Explanation Of Basic Concepts And Symbols
During printing, paper is supplied from the right side of the copier and fed into the Exit Tray on top with the printed surface of the page facing down. The paper feed direction is shown by the arrows in the diagram below. 1-12 Di152/Di183... -
Page 19: Width" And "Length
(B), the paper has a vertical or portrait orientation, indicated by either “L” or Crosswise ( If the width (A) of the paper is longer than the length (B), the paper has a horizontal or landscape orientation, indicated by either “C” or Di152/Di183 1-13... - Page 20 Introduction 1-14 Di152/Di183...
-
Page 21: Precautions
A location that is not near any kind of heating devices Power source The power source requirements are as follows. Voltage Fluctuation: Within±10% Frequency Fluctuation: Within ± 3Hz ❍ Use a power source with as few voltage or frequency fluctuations as possible. Di152/Di183... -
Page 22: Space Requirements
To ensure easy copier operation, supply replacement, and maintenance, adhere to the recommended space requirements detailed below. <Di152> 1038 <Di183> 1038 Unit: mm Note Be sure to allow a clearance of 100 mm or more at the back of the copier for the ventilation duct and 150 mm or more at the right of the copier for the removal of the misfed papers. -
Page 23: Operation Precautions
A negligible amount of ozone is generated during normal operation of this copier. An unpleasant odor may, however, be detected in poorly ventilated rooms during extensive copier operations. ➜ For a comfortable operating environment, it is recommended that the room be well ventilated. Di152/Di183... -
Page 24: Transporting The Copier
Keep all supplies out of the reach of children. CAUTION Be careful not to spill toner inside the copier or get toner on your clothes or hands. ➜ If your hands become soiled with toner, immediately wash them with soap and water. Di152/Di183... -
Page 25: Legal Restrictions On Copying
Copyrighted works without permission of the copyright owner In addition, it is prohibited under any circumstances to copy domestic or foreign currencies, or works of art, without permission of the copyright owner. When in doubt about the nature of a document, consult with legal counsel. Di152/Di183... - Page 26 Precautions Di152/Di183...
-
Page 27: Before Making Copies
Before Making Copies Available Features The main copy settings available with this copier are listed below. For details on their operation, refer to the pages indicated. Copies 1-sided copies (p.6-1) 2in1 copies (p.6-1) 4in1 copies (p.6-1) Book separation copies (p.6-2) Di152/Di183... - Page 28 Before Making Copies Zoom Ratio Reduced/Full Size/Enlarge (p.5-11) Finishing Sort (p.6-6) Group (p.6-8) Note The Finishing functions available are limited according to the options equipped to the copier. Di152/Di183...
- Page 29 Before Making Copies Applications Erase (p.6-10) Neg. Pos. Reverse (p.6-13) X/Y Zoom (p.5-14) File Margin (p.6-14) Mixed Orig. Detection Mixed Originals (p.4-4) Note The Mixed Orig. Detection function is available when the copier is equipped with an Automatic Document Feeder (option). Di152/Di183...
-
Page 30: Components And Their Functions
Before Making Copies Components and Their Functions Copier Di152/Di183 Original Cover Kit OC-5 (option) Presses down on an original placed on the Original Glass. Standard on Di152. Automatic Document Feeder AF-10 (option) Automatically feeds originals one page after another for scanning. - Page 31 Copy Desk CD-1H (option) Adjusts the height when a Paper Feed Cabinet is mounted. Fax unit for Di183/Di152 FX-1 (option) Permits fax transmission using this copier. Printer Controller Pi1802e (option) A built-in type printer controller that allows the copier to be used as a printer with the copier connected to a personal computer.
-
Page 32: Parts Names And Their Functions
Before Making Copies Parts Names and Their Functions Copier * The above illustrations represent a copier mounted with the optional Original Cover Kit. Di152/Di183... - Page 33 Holds the original against the Original Glass. Original Glass Place your original on this glass to allow the copier to scan it. The original is to be placed face down. (p.4-6) Control Panel Use to start a copy cycle and make necessary settings. (p.3-12) Di152/Di183...
-
Page 34: Inside The Copier
Forms a copy image. The Imaging Unit is to be replaced only by your Tech. Rep. Toner Bottle Holder Open to replace the Toner Bottle. Pressure Lever Use to clear a misfed sheet of paper at the Fusing Unit. (p.8-12) Di152/Di183... -
Page 35: Options
Description Bypass Tray Up to 50 sheets of plain paper or 20 sheets of special paper can be loaded on this tray. (p.8-7) Bypass Tray Extender Slide this Bypass Tray Extender out to load paper of a large size. Di152/Di183... - Page 36 Paper Feed Cabinet Part Name Description 2nd Tray Up to 250 sheets of plain paper can be loaded. (p.8-6) Di183 accepts a Paper Feed Cabinet of four trays. 3rd Tray Di152 accepts a Paper Feed Cabinet of one tray. 4thTray 5thTray Side Cover Open to clear a misfed sheet of paper.
- Page 37 Job Tray Part Name Description Copy Tray Lamp Lights up when paper is fed into the Upper Copy Tray. Upper Copy Tray Receives printed pages produced via the personal computer or faxes received. Lower Copy Tray Receives copies made. Di152/Di183 3-11...
-
Page 38: Control Panel
Pos. key • Press to copy an original with the original tonal arrangements reversed. Original key • Press to select the Mixed Org. or Book Separation function. Copy key • Press to select the 2in1 or 4in1 function. 3-12 Di152/Di183... - Page 39 Auto Paper/Auto Size • Press to select either Auto Paper or Auto Size. Paper key • Press to select the paper size Auto/Photo key • Press to adjust the image density of the copy. Di152/Di183 3-13...
-
Page 40: Icons On The Control Panel
Blinks or lights up when the time approaches that copier needs maintenance service. Call your Tech. Rep. Add Paper indicator Lights up when the paper source currently selected for use runs out of paper. Add Toner indicator Lights up when toner will soon run out. 3-14 Di152/Di183... -
Page 41: Turning On And Off And The Initial Mode
Automatic Document Feeder and pressing the [Start] key. Pressing the [Start] key at this time will not immediately start the copy cycle. Rather, you are going to have to wait for about 30 seconds (at an ambient temperature of 23°C). Di152/Di183 3-15... -
Page 42: Default Settings
Default settings Number of copies: 1 Exposure: Auto Zoom ratio: 100% (full size) Paper: Auto Paper (When Automatic Document Feeder is mounted) Finishing: Non-Sort The default settings can be customized by selecting User’s Choice. (p.7-2) 3-16 Di152/Di183... -
Page 43: Useful Functions
The length of time before the copier automatically resets itself can be set between 1 min and 5 min, in addition to 30 seconds. The Auto Panel Reset function can even be disabled. For more details, refer to “User’s Choice” (p.7-2, p.7-8). Di152/Di183 3-17... -
Page 44: Energy Saver
If a document is loaded and the [Start] key is pressed during the period after the copier has been turned ON but before it is ready to make copies, the copier will automatically start the copy cycle as soon as it completes the warm-up cycle. 3-18 Di152/Di183... -
Page 45: Interrupting Copy Jobs
If the current tray runs out of paper during a copy cycle and there is another tray loaded with paper of the same size and in the same direction, the copier will automatically select that tray to continue copying. Di152/Di183 3-19... -
Page 46: Account Number
The account number entry screen changes to the default setting indication, indicating that the copier is ready to make copies. Run the desired copy cycle. When the copy cycle is completed, press the [Access] key a second time. 3-20 Di152/Di183... -
Page 47: Printing From The Personal Computer
For details of operation, refer to the Printer Controller User Manual. Sending and Receiving Faxes Using the Copier When the optional Fax unit is mounted, fax transmission can be made using this copier. For details of operation, refer to the Fax unit User Manual, separately available. Di152/Di183 3-21... -
Page 48: Copy Paper
Card (91 g/m to 157 g/m ), OHP transparencies, postcards, labels Paper Size • Width: 90 mm to 297 mm • Length: 140 mm to 432 mm Capacity • Plain paper, recycled paper: 50 sheets • Special paper: 20 sheets 3-22 Di152/Di183... - Page 49 When loading paper of any FLS size other than the default setting (210 mm × 330 mm), setting by your Tech. Rep. is necessary. Consult your Tech. Rep. for this setting. For how to load paper, refer to “When the Add Paper Indicator Lights.” (p.8-4) Di152/Di183 3-23...
- Page 50 Before Making Copies 3-24 Di152/Di183...
-
Page 51: Loading Originals
• Weight of originals of mixed sizes: 60 g/m 90 g/m Original Glass Max. weight of sheet A3L to A5 originals, books, or three- • Original width: Up to 297 mm dimensional objects: 3 kg • Original length: Up to 432 mm Di152/Di183... -
Page 52: Loading Originals In The Automatic Document Feeder
When the original are loaded into the Automatic Document Feeder the original sizes that can be detected in the Auto Paper mode are A3L•B4L•A4L•A4C•B5L•B5C, LetterL, LetterC and FLS. The copier may not be able to detect, or may detect of any other size or irregular size. Di152/Di183... - Page 53 Automatic Document Feeder. Refer to “Mixed Originals.” (p.4-4) Make the necessary settings. ❍ Making Copies (p.5-1) ❍ Advanced Copying (p.6-1) Press the [Start] key to start feeding and copying the originals from the top page. Di152/Di183...
-
Page 54: Mixed Originals
Making Copies from Originals of Mixed Sizes Slide the front adjustable Document Guide Plate to the front of the copier. Load the originals face up in the Document Feeder Tray so that their rear edges are in correct alignment with the Document Guide Plate. Di152/Di183... - Page 55 Press the [Original] key to light the Mixed Orig. lamp. Press the [Auto Paper/Auto Size] key to light the Auto Paper lamp. Press the [Start] key to start feeding and copying the originals from the top page. Di152/Di183...
-
Page 56: Place The Original On The Original Glass
Let the copier scan the contents of the original with the Original Cover or the Automatic Document Feeder raised. Do not attempt to push the Original Glass with excessive force, as a malfunction could result. (The maximum load resistance of the Original Glass is 3 kg.) Di152/Di183... -
Page 57: How To Position A Sheet Original
Position the original in the left rear corner aligned with the marker on the scale. Gently lower the Automatic Document Feeder or Original Cover. Make the necessary settings. ❍ Making Copies (p.5-1) ❍ Advanced Copying (p.6-1) Press the [Start] key to start the copy cycle. Di152/Di183... -
Page 58: Highly Transparent Originals
Place a blank sheet of paper of the same size over the original. Gently lower the Automatic Document Feeder or Original Cover. Make the necessary settings. ❍ Making Copies (p.5-1) ❍ Advanced Copying (p.6-1) Press the [Start] key to start the copy cycle. Di152/Di183... -
Page 59: Books
Document Feeder or Original Cover. Do not look directly at the Original Glass surface during a scanning sequence since a strong beam of light is emitted. This light beam is not, however, a laser beam and is not as dangerous. Make the Book Separation setting. ❍ Book Separation (p.6-3) Di152/Di183... - Page 60 Loading Originals 4-10 Di152/Di183...
-
Page 61: Making Copies
The following procedure describes how to place an original and make a basic copy of it. Making a Basic Copy Position the original. ❍ Original Loading (p.4-1) Make the necessary control panel settings. ❍ Selecting the Paper (p.5-3) ❍ Zoom Ratio (p.5-11) ❍ Image Density (p.5-16) Di152/Di183... - Page 62 Enter the number of copies to be made from the 10-Key Pad. Any number from 1 to 99 can be entered. Press the [Start] key. This will start the copy cycle. To stop the copy cycle in mid- operation, press the [Stop] key. Di152/Di183...
-
Page 63: Selecting The Paper
[Start] key has been pressed, the paper size indicator on the control panel starts blinking. Load the paper whose paper size indicator is blinking or press the [Paper] key and select another desired paper size before pressing the [Start] key again. Di152/Di183... - Page 64 User’s Choice. Details: OHP transparencies Cards and postcards Plain paper If plain paper is set in User’s Choice, the “1” mark will not be displayed even if cards or postcards, or OHP transparencies, are loaded in the tray. Di152/Di183...
-
Page 65: Feeding Paper Manually
Insert one sheet of paper at a time when using the Manual Bypass Tray to make a copy. If the optional Multiple Bypass is mounted, the Bypass Tray can hold up to 50 sheets of paper, or 20 sheets of cards, postcards, or OHP transparencies. Di152/Di183... -
Page 66: Making Copies By Using The Bypass Tray
(p.5-9) Do you know which FLS size has been set? ➜ The FLS size has been set to 210 mm × 330 mm. Ask your Tech. Rep. if you want to change the FLS size. Press the [Enter] key. Di152/Di183... - Page 67 Bypass Tray: This will automatically start the new copy cycle. To make copies continuously on cards, OHP transparencies, or postcards, load the paper in the 1st Tray. Refer to “Copy Paper”(p.3- 22) and “Adding Paper” (p.8-4). Di152/Di183...
- Page 68 The FLS size has been set to 210 mm × 330 mm. Ask your Tech. Rep. if you want to change the FLS size. Press the [Enter] key. Make any other necessary settings. ❍ Zoom Ratio (p.5-11) ❍ Image Density (p.5-16) Press the [Start] key. Di152/Di183...
- Page 69 Bypass Tray location indicator on the control panel lights. Press the [Bypass Tray Size Select] key until the Custom Size indicator blinks. Press the [Enter] key. Press the [Clear] key to clear the old value shown on the Display. Di152/Di183...
- Page 70 ➜ The width can range from 90 mm to 297 mm. Do you want to change the value just entered? ➜ Press the [Clear] key and then re-enter the new value. Press the [Enter] key. 5-10 Di152/Di183...
-
Page 71: Specifying The Zoom Ratio
This setting makes a copy the same size as the original (100%). X/Y Zoom This setting allows the zoom ratio to be set independently for X (horizontal) and Y (vertical) directions. The ratios can be set directly from the 10-Key Pad, in the range between 50% and 100%. Di152/Di183 5-11... -
Page 72: Setting The Zoom Ratio
Press the [Paper] key on the control panel until the desired paper size indicator lights. Make any other necessary settings. ❍ Image Density (p.5-16) Enter the number of copies to be made from the 10-Key Pad and then press the [Start] key. 5-12 Di152/Di183... - Page 73 Pressing this key changes the ratio in 1% increments. Make any other necessary settings. ❍ Paper (p.5-3) ❍ Image Density (p.5-16) Enter the number of copies to be made from the 10-Key Pad and then press the [Start] key. Di152/Di183 5-13...
- Page 74 Press the [Clear] key and then re-enter the new value. What happens when a value outside the specified range is entered? ➜ The Display shows “Err.” Press the [Clear] key and re-enter a new value that falls within the Y (width) range. (length) 5-14 Di152/Di183...
- Page 75 Y in X/Y Zoom? ➜ The ratio can range from 50% to 100%. Make any other necessary settings. ❍ Image Density (p.5-16) Enter the number of copies to be made from the 10-Key Pad and then press the [Start] key. Di152/Di183 5-15...
-
Page 76: Adjusting The Image Density
Position the original. ❍ Original Loading (p.4-1) Press the [Auto/Photo] key on the control panel to select the desired mode. Do you know how to select Auto? ➜ Light the auto exposure lamp as shown on the right. Auto 5-16 Di152/Di183... - Page 77 (Level 0) Darker (Level 1) Darkest (Level 2) Make any other necessary settings. ❍ Paper (p.5-3) ❍ Image Density (p.5-16) Enter the number of copies to be made from the 10-Key Pad and then press the [Start] key. Di152/Di183 5-17...
-
Page 78: Interrupting A Copy Job
When the [Interrupt] key is pressed, all functions and settings indicated on the control panel are reset to their defaults. Remove the original of the interrupted copy job and then position the new one that you want to copy. 5-18 Di152/Di183... - Page 79 The Interrupt indicator will go out and the settings will be recovered for the interrupted copy job. Reposition the original for the interrupted copy job that has been removed in step 2. Press the [Start] key. The interrupted copy job will be resumed. Di152/Di183 5-19...
- Page 80 Making Copies 5-20 Di152/Di183...
-
Page 81: Advanced Copying
4in1: Important) ✔ This setting is available only when the copier is equipped with an Au- tomatic Document Feeder. ➜ The copier copies four different 1- Originals Copy sided originals onto one side of a single sheet of paper. Di152/Di183... - Page 82 ❍ Original Loading (p.4-1) Press the [Copy] key to light either the 2in1 or 4in1 indicator. Make any other necessary settings. Enter the number of copies to be made from the 10-Key Pad and then press the [Start] key. Di152/Di183...
- Page 83 Erases a given width along the outside edges. ➜ Center Erase: Original Copies Erases a given width down the center. ➜ Frame + Center Erase: Original Copies Erases a given width along the outside edges as well as down the center. Di152/Di183...
- Page 84 To change the setting for the frame erase width, use “Erase Set- ting” of User’s Choice. (p.7-8) Make any other necessary settings. Enter the number of copies to be made from the 10-Key Pad and then press the [Start] key. Di152/Di183...
-
Page 85: Finishing Copies (Sort And Group)
The copies are automatically divid- Originals Copies ed into sets with each set containing a copy of each page. Group: ➜ The copies are automatically divid- Originals Copies ed into stacks with each stack con- taining copies of the same page. Di152/Di183... -
Page 86: Sorting
✔ The copier must be equipped with an Automatic Document Feeder and a Shifting Unit. ➜ The sorted copy sets are stacked in the same direction, but in a saw- tooth manner by shifting the tray for each set. Di152/Di183... - Page 87 Note To enable crisscross sorting, the copier must be loaded with paper of the same size and same paper type, but in two different directions. Note Crisscross sorting cannot be effected if a Shifting Unit is mounted. Di152/Di183...
-
Page 88: Grouping
Note To enable crisscross grouping, the copier must be loaded with paper of the same size and same paper type, but in two different directions. Di152/Di183... - Page 89 Sort and Group lamps are off? ➜ It means that Non-Sort is cur- rently selected for use. Make any other necessary settings. Enter the number of copies to be made from the 10-Key Pad and then press the [Start] key. Di152/Di183...
-
Page 90: Erasing Part Of Original Image (Erase)
A given width along all four edges is Original Copy erased. What is Center Erase? ➜ A given width is erased down the Original Copies center. Note This setting is available only when Book Separation is selected. (p.6-3) 6-10 Di152/Di183... -
Page 91: Precautions For Erase Position
Precautions for Erase Position Note the correct direction of positioning the original when making copies in the Erase mode. For more details, refer to the table given below. Automatic Document Result Original Glass Feeder Left Erase Upper Erase Frame Erase Di152/Di183 6-11... - Page 92 To change the erase width, change the setting for “Erase Setting” of User’s Choice. (p.7-8) Make any other necessary settings. Enter the number of copies to be made from the 10-Key Pad and then press the [Start] key. 6-12 Di152/Di183...
-
Page 93: Reversing Original Tonal Arrangements (Neg. Pos. Reverse)
Original Loading (p.4-1) Press the [Neg. Pos.] key and make sure that the Neg. Pos. lamp lights. Make any other necessary settings. Enter the number of copies to be made from the 10-Key Pad and then press the [Start] key. Di152/Di183 6-13... -
Page 94: Providing A File Margin
To change the file margin width, change the setting for “Margin Setting” of User’s Choice. (p.7-7) Make any other necessary settings. Enter the number of copies to be made from the 10-Key Pad and then press the [Start] key. 6-14 Di152/Di183... -
Page 95: Using The Utility Mode
Hold down the [Panel Reset] key for 3 seconds. Check that “U--” appears on the Display. Using the 10-Key Pad, enter the code corresponding to the desired subfunction. E.g.: Enter “1” to make a setting for User’s Choice. Press the [Start] key. Di152/Di183... -
Page 96: User's Choice
Mixed Orig. disabled Paper Priority FLS L 11×17L 11×14L Legal L Letter L 5-1/2×8-1/2L Letter C 5-1/2×8-1/2C 1st Tray 2nd Tray 3rd Tray *1 4th Tray *1 5th Tray *1 Multiple Bypass Tray Copy Priority Auto Paper Auto Size Manual Di152/Di183... - Page 97 Output Priority Non-Sort Sort Group Crisscross Mode Crisscross stacking enabled Crisscross stacking disabled 4in1 Copy Order Pattern A Pattern B Book Binding Position Left-bound Right-bound Margin Setting 10mm 20mm Erase Setting (Left) 10mm 20mm Erase Setting (Upper) 10mm 20mm Di152/Di183...
- Page 98 15 min 240 min Auto Shut OFF Auto Shut OFF disabled 15 min 30 min 240 min Density (ADF) Mode 1 Mode 2 Print Density Paper Auto Detection (1st Inch Tray) Metric Paper Auto Detection (2nd Inch Tray) Metric Di152/Di183...
- Page 99 Auto Paper disabled, Auto Tray Switching enabled Auto Paper disabled, Auto Tray Switching disabled Special Paper Setting Auto Paper enabled (4thTray) *1 (Special Paper Setting OFF) Auto Paper disabled, Auto Tray Switching enabled Auto Paper disabled, Auto Tray Switching disabled Di152/Di183...
-
Page 100: Mixed Orig
(Special Paper Setting OFF) Auto Paper disabled, Auto Tray Switching enabled Auto Paper disabled, Auto Tray Switching disabled *1: Di183 Only Mixed Orig. Select whether to enable Mixed Orig. as the default setting. The default value is “Mixed Orig. disabled.” Paper Priority Select a paper size or paper source that will be selected automatically when Auto Size is selected. -
Page 101: Exposure Level Priority (Manual)
(Right-bound) first when it scans an open book. The default value is “Left-bound.” Margin Setting Choose the width of the file margin to be set in the copy in the range between 0 mm and 20 mm (in 1-mm increments). The default value is “10 mm.” Di152/Di183... -
Page 102: Erase Setting (Left, Upper, And Frame)
Select the image density level of copies and printed pages from among “-2,” “-1,” “0,” “1,” or “2.” The smaller the value, the lighter the image, and the greater the value, the darker the image with “0” as the central value. The default value is “0.” Di152/Di183... -
Page 103: Paper Auto Detection
“you want an uninterrupted copy cycle to use recycled paper even when plain paper runs out.” The default value is “Auto Paper enabled (special paper setting OFF).” Making the User’s Choice Settings User’s Choice Setting Procedure Call the Utility Mode to the Display. Di152/Di183... - Page 104 Check that “c--” appears on the Display. Enter the code assigned to the desired function from the 10-Key Pad. E.g.: Enter “3” to change the setting for “Copy Priority.” Press the [Start] key. Press the [Clear] key. This clears the current setting. 7-10 Di152/Di183...
- Page 105 Press the [Clear] key and then enter § the new setting. Press the [Start] key. To further change the setting for another function, repeat steps 4 through 9. Press the [Panel Reset] key to return to the default settings. Di152/Di183 7-11...
-
Page 106: Drum Dehumidify
Running the Drum Dehumidify Sequence Call the Utility Mode to the Display. Calling the Utility Mode to the Display (p.7-1) Making sure that “U--” appears on the Display, enter “2” from the 10-Key Pad. Press the [Start] key. 7-12 Di152/Di183... -
Page 107: Toner Replenisher (Auxiliary Toner Replenishing)
Running the Toner Replenisher Sequence Call the Utility Mode to the Display. Calling the Utility Mode to the Display (p.7-1) Making sure that “U--” appears on the Display, enter “3” from the 10-Key Pad. Press the [Start] key. Di152/Di183 7-13... -
Page 108: Custom Size Input
Custom Size Input Procedure (1st Tray) Call the Utility Mode to the Display. Calling the Utility Mode to the Display (p.7-1) Making sure that “U--” appears on the Display, enter “4” from the 10-Key Pad. Press the [Start] key. 7-14 Di152/Di183... - Page 109 Press the [Clear] key and then enter § the new value. Do you know the range for the paper width of custom size? § The width can range from 90 mm to 297 mm. Press the [Enter] key. Di152/Di183 7-15...
-
Page 110: Administrator Mode
Settings for the Administrator Mode Call the Utility Mode to the Display. Calling the Utility Mode to the Display (p.7-1) Making sure that “U--” appears on the Display, enter “5” from the 10-Key Pad. Press the [Start] key. 7-16 Di152/Di183... - Page 111 Do you know the code for Copy Track? To select Copy Track, enter “1.” § Do you know the code for Disable Auto Shut OFF? To select Disable Auto Shut OFF, enter “2.” § Press the [Start] key. Di152/Di183 7-17...
-
Page 112: Copy Track
Copy Track Setting Procedure (A-1) Call the Administrator Mode to the Display. Calling the Administrator Mode to the Display (p.7-16) Making sure that “Ad-” appears on the Display, enter “1” from the 10-Key Pad. Press the [Start] key. 7-18 Di152/Di183... - Page 113 10-Key Pad. Do you know the code for “enabling” Copy Track? To enable Copy Track, enter “0.” § Do you know the code for “disabling” Copy Track? To disable Copy Track, enter “1.” § Press the [Start] key. Di152/Di183 7-19...
- Page 114 999. If an account number entered already exists, the entry will be rejected. § Enter a different number. Press the [Start] key. This stores the account number. To program another account number successively, repeat steps 4 through 7. 7-20 Di152/Di183...
- Page 115 Press [ ] or [ ] key to select the account number to be deleted. Press the [Start] key. The selected account number will be deleted. Do you know what to do to delete another account number? Repeat steps 4 through 7. § Di152/Di183 7-21...
- Page 116 Press [ ] or [ ] key to select the account number to be changed. Press the [Start] key to delete the old account number. Enter the new account number from the 10-Key Pad. Press the [Start] key. This stores the new account number. 7-22 Di152/Di183...
- Page 117 Making sure that “A--” appears on the Display, enter “5” from the 10-Key Pad. Press the [Start] key. Press [ ] or [ ] key to select the account number for which you want to check the Total Counter value. Press the [Start] key. Di152/Di183 7-23...
- Page 118 Then, the Display returns to the status that allows you to select the account number, in step 6. Do you know how to check or reset the Total Counter of another account successively? Repeat steps 6 through 9. § 7-24 Di152/Di183...
- Page 119 Making sure that “A--” appears on the Display, enter “6” from the 10-Key Pad. Press the [Start] key. Check that the Display shows “CLr.” Press the [Start] key. This clears the Total Counter values of all accounts, resetting them to “0.” Di152/Di183 7-25...
-
Page 120: Disable Auto Shut Off
Call the Administrator Mode to the Display. Calling the Administrator Mode to the Display (p.7-16) Making sure that “Ad-” appears on the Display, enter “2” from the 10-Key Pad. Press the [Start] key. Press the [Clear] key. This clears the current setting. 7-26 Di152/Di183... - Page 121 Using the Utility Mode Enter the new setting from the 10-Key Pad. Do you know the number for “authorize” Disable Auto Shut OFF? § Enter “0.” Press the [Start] key. This validates the new setting. Di152/Di183 7-27...
-
Page 122: Checking The Total Number Of Copies/Prints Produced
Using the [Meter Count] Key Press the [Meter Count] Key. Make sure that “tc” appears on the Display. The Total Counter value is then displayed. E.g.: The Display looks like the one shown on the right when the value is 1,234. 7-28 Di152/Di183... - Page 123 The Size Counter value is then displayed. E.g.: The Display looks like the one shown on the right when the value is 123. After you have checked the counter value or values, press the [Meter Count] key. Then the original display reappears. Di152/Di183 7-29...
-
Page 124: Storing A Job
Each time the [Job Input] key is § pressed, the Display alternates between “Jb1” and “Jb2.” Do you know what happens if another job has already been stored in the job number selected? Storing a new job will erase the old one. § 7-30 Di152/Di183... - Page 125 Using the Utility Mode Press the [Enter] key. The Display changes as shown on the right, indicating that the job has been stored in Jb1. Di152/Di183 7-31...
- Page 126 Do you know how to change the contents of the Display? Each time the [Job Recall] key is § pressed, the Display alternates between “Jb1” and “Jb2.” Press the [Enter] key. Press the [Start] key. 7-32 Di152/Di183...
-
Page 127: Error Displays And Other Indicators
“Clearing a Paper Misfeed” (p.8-12) A paper (original) misfeed has Identify the misfeed location on occurred in the Automatic the control panel and remove the Document Feeder. sheet of misfed paper. “Clearing a Paper Misfeed” (p.8-19) Di152/Di183... - Page 128 The Plug-In Counter is not Plug in the Plug-In Counter. plugged in. The numerical value entered Check the value and enter the falls outside the setting range. correct one as necessary. The scheduled maintenance Call your Tech. Rep. time has arrived. Di152/Di183...
- Page 129 Turning OFF, then ON, the copier the copier. will minor malfunciton. If this does not reset the minor malfunction, call your Tech. Rep. and give him or her the malfuncion code being shown on the Display. E.g.: C0510 Fusing malfunction Di152/Di183...
-
Page 130: When The Add Paper Indicator Lights Up
➜ Be careful not to touch the surface of the Paper Take-Up Roll. Press down on the Paper Lifting Paper Lifting Plate Plate until it clicks into the locked position. Di152/Di183... - Page 131 Do you know the special precautions to be used when loading paper? ➜ Be sure that the Edge Guide and Trailing Edge Stop are pressed tightly up against the edges of the paper stack. Slide the tray back into the copier. Di152/Di183...
- Page 132 Do you know the special precautions to be used when loading paper? ➜ Be sure that the Edge Guide and Trailing Edge Stop are pressed tightly up against the edges of the paper stack. Slide the tray back into the copier. Di152/Di183...
- Page 133 Ä mark. ➜ Be sure to smooth any curl in the paper before loading it. Adjust the Paper Guides and the Bypass Tray Extender to the size of the paper. Di152/Di183...
-
Page 134: When The Add Toner Indicator Lights Up
Do not throw away, but keep, the used Toner Bottle, which will be collected by your Tech. Rep. Replacing the Toner Bottle Open the Front Cover. Pull the Toner Bottle Holder to the front and gently pull out the used Toner Bottle. Di152/Di183... - Page 135 Do you know how much you need to insert the bottle? ➜ Fit the protrusion on the Toner Bottle all the way into the recess in the holder as illustrated. Tap the bottom of Toner Bottle three to four times. Di152/Di183...
- Page 136 Front Cover is closed. Do you know what to do if the copy image density is still low immediately after the Toner Bottle has been replaced with a new one? ➜ Run “Toner Replenisher” of Utility Mode. (p.7-13) 8-10 Di152/Di183...
-
Page 137: When The Paper Misfeed Indicator Lights
A blinking lamp indicates that there is a misfed sheet of paper. Different procedures are used to clear a misfed sheet of paper depending on the location. First, isolate the location, then clear the misfeed according to the procedure applicable to the misfeed occurring at that Di152/Di183 8-11... -
Page 138: Clearing A Paper Misfeed
Do not touch any area other than the authorized knobs, to reduce the risk of burns. CAUTION There are a number of protrusions on the backside of the guide plate. ➜ To avoid possible injury, be careful not to touch any areas other than the paper. 8-12 Di152/Di183... - Page 139 Error Displays and Other Indicators Open the Side Cover of the copier. Unlock the Pressure Lever of the Fusing Unit. Do you know how to unlock the Pressure Lever? ➜ Grasp the green lever to unlock the Pressure Lever. Pressure Lever Di152/Di183 8-13...
- Page 140 Do you know which part to grasp to turn the roller? ➜ Be sure to grasp the green knob to turn the roller. Lock the Pressure Lever into position. 8-14 Di152/Di183...
- Page 141 Are you informed of special precautions to be used when loading paper? ➜ Be sure that the Edge Guide and Trailing Edge Stop are pressed tightly up against the edges of the paper stack. Slide the 1st Tray back into the copier. Di152/Di183 8-15...
- Page 142 Error Displays and Other Indicators <Paper Feed Cabinet> Open the Side Cover of the Paper Feed Cabinet. Gently pull out the sheet of misfed paper. Close the Side Cover of the Paper Feed Cabinet. 8-16 Di152/Di183...
- Page 143 Error Displays and Other Indicators <Multiple Bypass Tray> Unload the paper stack from the Bypass Tray. Open the Side Cover of the copier. Gently pull out the sheet of misfed paper. Close the Side Cover. Di152/Di183 8-17...
- Page 144 Error Displays and Other Indicators Load the paper stack back in the Bypass Tray. 8-18 Di152/Di183...
- Page 145 Error Displays and Other Indicators <Automatic Document Feeder> Open the Document Feeder Cover. Unload the document from the Document Feeder Tray. Raise the Automatic Document Feeder. Di152/Di183 8-19...
- Page 146 Error Displays and Other Indicators Turning the document feed knob in the direction of the arrow, gently pull out the original. Close the Document Feeder Cover. 8-20 Di152/Di183...
- Page 147 Reload the document which has been unloaded in step 2. Do you know what to do if “-1” is shown on the Display? ➜ Merge the original which has been misfed with the remaining pages of the document for reloading. Di152/Di183 8-21...
- Page 148 Error Displays and Other Indicators 8-22 Di152/Di183...
-
Page 149: Troubleshooting Tips
(p.4-6) The copy is blurry. The paper is damp. Change the paper. (p.8-4) The original is not placed Place the original in position firmly against the Original so that it is placed firmly Glass. against the Original Glass. (p.4-6) Di152/Di183... - Page 150 Select the zoom ratio is not in accord with the according to the paper size. paper size (when the copy is (p.5-13) Or, use Auto Size to made at a manually adjusted reduce the copy to the reduction ratio). appropriate size. (p.5-12) Di152/Di183...
- Page 151 Trailing Edge Stop up up against the paper stack in against the edges of the the tray. paper stack. The paper has an excessive Smooth out curl in the paper curl. and reload the paper stack in the tray. Di152/Di183...
-
Page 152: When The Copier Is Not Operating Correctly
(p.3-19) The copier cannot be turned The power cord is unplugged Plug the power cord into the from the power outlet. power outlet. The room’s circuit breaker is Close the room’s circuit tripped. breaker. Di152/Di183... -
Page 153: Appendix
Appendix Appendix 10.1 Specifications Copier Di152/Di183 Specifications Di152 Di183 Type Desktop Platen Type Stationary Photo conductor Copying System Electrostatic Dry Powdered Image Transfer to Plain Paper Developing System Micro-Toning Hight-Grade System Fusing System Lamp-Heated Roller Resolution 600dpi Types of Original •... - Page 154 Appendix Specifications Di152 Di183 Exposure Control Auto Exposure Mode, Manual Exposure Mode and Photo Manual Exposure Mode Lost Image Leading Edge: 4 mm Trailing Edge: 4 mm Rear Edge: 4 mm Front Edge: 4 mm Power Requirements 220V to 240V, 15 A, 50/60 Hz Power Consumption 1.5 kW or less...
-
Page 155: Paper Feed Cabinet Pf-120
A3L to A5C, FLS (210 mm × 330 mm) Inch system equivalent 11 × 17L, 11 × 14L, Legal L, Letter, 5-1/2 × 8-1/2C Capacity 250 sheets Power Consumption 9 W or less Dimensions Width: 535 mm Depth: 568 mm Height: 137 mm Weight 5.5 kg Di152/Di183 10-3... -
Page 156: Shifting Unit Ot-103
Width: 90 mm to 297 mm Length: 140 mm to 432 mm Capacity Plain paper,recycled paper: 50 sheets Special paper: 20 sheets Power Consumption 9 W or less Dimensions Width: 436 mm Depth: 489 mm Height: 137 mm Weight Approx. 2.7 kg 10-4 Di152/Di183... -
Page 157: Care Of The Copier
Wipe the surface of the control panel clean with a soft, dry cloth. Do you know if detergent can be used for cleaning? ➜ NEVER use household detergent or glass cleaner, as a damaged control key could result. Di152/Di183 10-5... -
Page 158: Function Combination Table
The functions cannot be combined. (The function set last takes precedence.) The function set first takes precedence if paper is loaded in the Bypass Tray. The functions can be combined in the Book Separation mode only. The functions cannot be combined. 10-6 Di152/Di183... -
Page 159: List Of Paper Sizes And Zoom Ratios
Letter 8-1/2 × 11 216 mm × 279 mm Government 8 × 10-1/2 203 mm × 267 mm Letter Quarto 8 × 10 203 mm × 254 mm Statement Invoice 5-1/2 × 8-1/2 140 mm × 216 mm Di152/Di183 10-7... -
Page 160: Zoom Ratios(Original Size To Paper Size)
11-3/4 × 16-1/2 210mm × 297mm 8-1/4 × 11-3/4 141% 122% 148mm × 210mm 5-3/4 × 8-1/4 141% 200% 173% 122% 200% 105mm × 148mm 141% 4-1/4 × 5-3/4 173% 122% 257mm × 364mm 10 × 14-1/4 115% 10-8 Di152/Di183... - Page 161 11 × 14 279.4mm × 381mm Legal Foolscap Letter 5-1/2 × 8-1/2 11 × 14 Legal 279.4mm × 355.6mm Foolscap Letter 5-1/2 × 8-1/2 Legal Foolscap 8-1/2 × 14 Letter 215.9mm × 355.6mm 5-1/2 × 8-1/2 11 × 17 121% Di152/Di183 10-9...
- Page 162 11 × 17 200% 5-1/2 × 8-1/2 11 × 14 164% 139.7mm × 215.9mm Legal 154% Foolscap 150% Letter 129% * Zoom Ratio = Paper Size ÷ Original Size 1 Inch = 25.4 mm 1 mm = 0.0394 Inch 10-10 Di152/Di183...
- Page 163 Introduction We Want You to Be a Satisfied Customer ........1-1 CE Marking (Declaration of Conformity) .........1-1 SAFETY INFORMATION..............1-2 Warning and Precaution Symbols...........1-2 Meaning of Symbols................1-2 WARNING..................1-3 CAUTION ..................1-4 Precautions for Routine Use ............1-5 Safety Information.................1-6 Laser Safety ..................1-6 Internal Laser Radiation ..............1-6 CDRH Regulation................1-7 For European Users................1-8 For Denmark Users.................1-8...
- Page 164 Before Making Copies Available Features................ 3-1 Components and Their Functions ..........3-4 Parts Names and Their Functions ..........3-6 Copier ..................... 3-6 Inside the Copier ................3-8 Options ................... 3-9 Control Panel ................3-12 Names of Control Panel Parts and Their Functions ..... 3-12 Icons on the Control Panel ............
- Page 165 Making Copies Copying..................5-1 Selecting the Paper...............5-3 Feeding Paper Manually ...............5-5 Making Copies by Using the Bypass Tray ........5-6 Specifying the Zoom Ratio............5-11 Setting the Zoom Ratio ..............5-12 Adjusting the Image Density............5-16 Interrupting a Copy Job..............5-18 Advanced Copying Making 1-Sided Copies..............6-1 Finishing Copies (Sort and Group) ..........6-5 Three Finishing Types..............6-5 Sorting.....................6-6...
- Page 166 When This Type of Copy is Produced ........9-1 When the Copier is not Operating Correctly......9-4 10 Appendix 10.1 Specifications ................10-1 Copier Di152/Di183 ..............10-1 Automatic Document Feeder AF-10 ..........10-3 Paper Feed Cabinet PF-120............10-3 Shifting Unit OT-103 ..............10-4 Job Tray JS-202 ................10-4...
- Page 167 10.2 Care of the Copier ...............10-5 Cleaning ..................10-5 10.3 Function Combination Table............10-6 Function Combination Table ............10-6 Conditions for Combined Functions..........10-6 10.4 List of Paper Sizes and Zoom Ratios ........10-7 Paper Sizes...................10-7 Zoom Ratios(Original Size to Paper Size) ........10-8...
- Page 169 Clear key ...................3-13 Clearing a Paper Misfeed ..............8-12 Control Panel ..................3-12 Copy Paper ..................3-22 Custom Size Input (Bypass Tray) ............5-9 Custom Size Input Procedure (1st Tray) ...........7-14 Default Settings .................3-16 Delete Account Procedure ..............7-21 Enter key ...................3-13 Erase ....................6-10 Di152/Di183 Index-1...
- Page 170 Misfeed Indications and Misfeed Locations ........8-11 Mixed Originals ................... 4-4 Neg. Pos. Reverse ................ 6-13 Panel Resetting ................. 3-17 Paper Type ..................7-9 Photo mode ..................5-16 Ratios set using Zoom ([ ][ ]) key ..........5-11 Index-2 Di152/Di183...
- Page 171 Toner Replenisher (Auxiliary Toner Replenishing) ......7-13 Turn ON/OFF the Copier ..............3-15 User’s Choice ..................7-2 Using “Auto Paper” ................5-3 Using the Utility Mode ................7-1 When the Copier is not Operating Correctly ........9-4 When This Type of Copy is Produced ..........9-1 X/Y Zoom ...................5-11 Di152/Di183 Index-3...
- Page 172 Index Index-4 Di152/Di183...