Download Table of Contents Print this page
Panasonic KX-TDE200 Installation Manual

Panasonic KX-TDE200 Installation Manual

Pure ip-pbx
Hide thumbs Also See for KX-TDE200:

Advertisement

Table of Contents
Thank you for purchasing a Panasonic Pure IP-PBX.
Please read this manual carefully before using this product and save this manual for future use.
KX-TDE100/KX-TDE200: PMMPR Software File Version 3.0000 or later

Installation Manual

Pure IP-PBX
KX-TDE100
Model No.
KX-TDE200
SD Logo is
a trademark.

Advertisement

Table of Contents
loading

Related Manuals for Panasonic KX-TDE200

Summary of Contents for Panasonic KX-TDE200

  • Page 1: Installation Manual

    Model No. KX-TDE200 Thank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual for future use. SD Logo is KX-TDE100/KX-TDE200: PMMPR Software File Version 3.0000 or later a trademark.
  • Page 2: System Components

    System Components System Components System Components Table Category Model No. Description Shelves KX-TDE100 Basic Shelf KX-TDE200 Basic Shelf Main Processing Card IP Convergence Main Processing Card (IPCMPR) IPCMPR Option Cards KX-TDE0105 Memory Expansion Card (IPCMEC) KX-TDE0110 16-Channel VoIP DSP Card (DSP16)
  • Page 3 System Components Category Model No. Description KX-NCS2101 Activation Key for CA Basic for 1 User (CA Basic 1user) KX-NCS2105 Activation Key for CA Basic for 5 Users (CA Basic 5users) KX-NCS2110 Activation Key for CA Basic for 10 Users (CA Basic 10users) KX-NCS2140 Activation Key for CA Basic for 40 Users (CA Basic...
  • Page 4 System Components Category Model No. Description Physical Trunk Cards KX-TDA0180 8-Port Analogue Trunk Card (LCOT8) KX-TDA0181 16-Port Analogue Trunk Card (LCOT16) KX-TDA0182 8-Port DID Card (DID8) KX-TDA0183 4-Port Analogue Trunk Card (LCOT4) KX-TDA0184 8-Port E & M Trunk Card (E&M8) KX-TDA0187 T-1 Trunk Card (T1) KX-TDA0188...
  • Page 5 System Components Category Model No. Description Other Physical Cards KX-TDA0161 4-Port Doorphone Card (DPH4) KX-TDA0162 2-Port Doorphone Card (German Type) (DPH2) KX-TDA0164 4-Port External Input/Output Card (EIO4) KX-TDA0166 16-Channel Echo Canceller Card (ECHO16) KX-TDA0168 Extension Caller ID Card (EXT-CID) KX-TDA0190 Optional 3-Slot Base Card (OPB3) KX-TDA0191 4-Channel Message Card (MSG4)
  • Page 6 KX-T7765 Note that the types of activation keys are subject to change without notice. For CA activation keys, refer to the documentation for Equipment Compatibility Compatible Panasonic Proprietary Telephones The PBX supports the following telephones: • IP proprietary telephones (e.g., KX-NT300 series) •...
  • Page 7 Note • Some optional service cards and features are not available for certain countries/areas. Consult your certified Panasonic dealer for detailed instructions. • In this manual, the suffix of each model number (e.g., KX-TDE100NE) is omitted unless necessary. Installation Manual...
  • Page 8: Safety Notices

    System Components Safety Notices Please observe the safety notices in this manual in order to avoid danger to users or other people, and prevent damage to property. The notices are classified as follows, according to the severity of injury or damage: WARNING This notice means that misuse could result in death or serious injury.
  • Page 9: Important Safety Instructions

    Important Safety Instructions Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: • Do not use the product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
  • Page 10: Important Information

    Important Information Important Information SAVE THESE INSTRUCTIONS WARNING SAFETY REQUIREMENTS For All Telephone Equipment • Do not install the product in any other way than described in relevant manuals. • The product must only be installed and serviced by qualified service personnel. The product should be used as-is from the time of purchase;...
  • Page 11 Unplug this unit from the AC outlet if it emits smoke, an abnormal smell or makes unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped and contact an authorised Panasonic Factory Service Centre. •...
  • Page 12 Contact your telephone company. If all SLTs operate properly, there may be a problem with your PBX. Do not reconnect the PBX to the trunks until it has been serviced by an authorised Panasonic Factory Service Centre. Installation Manual...
  • Page 13 A replacement fuse cover can be purchased from your local Panasonic dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE AC OUTLET IN YOUR PREMISES, THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
  • Page 14 Precaution During dialling, this apparatus may tinkle the bells of other telephones using the same line. This is not a fault and we advise you not to call the Fault Repair Service. For users in the European Union only Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.
  • Page 15 Precaution that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom’s network services. • This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed.
  • Page 16 Introduction Introduction This Installation Manual is designed to serve as an overall technical reference for the Panasonic Pure IP-PBX, KX-TDE100/KX-TDE200. It provides instructions for installing the hardware, and programming the PBX using the Maintenance Console. The Structure of this Manual...
  • Page 17: Table Of Contents

    3.2.10 Fastening an Amphenol Connector ................71 3.2.11 Wall Mounting (KX-TDE200) ..................73 3.2.12 Wall Mounting (KX-TDE100) ..................75 3.2.13 Floor Standing (KX-TDE200 Only) .................77 3.2.14 Surge Protector Installation ....................79 Information about the Main Processing Card ..............82 3.3.1 IPCMPR Card .........................82 3.3.2 DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111) ........85 3.3.3...
  • Page 18 Table of Contents 3.5.9 PRI30 Card (KX-TDA0290CE/KX-TDA0290CJ) ............108 3.5.10 PRI23 Card (KX-TDA0290) ..................111 3.5.11 IP-GW4E Card (KX-TDA0484) ..................114 3.5.12 IP-GW16 Card (KX-TDA0490) ..................116 Information about the Physical Extension Cards ............118 3.6.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) ........118 3.6.2 DHLC8 Card (KX-TDA0170) ..................120 3.6.3 DLC8 Card (KX-TDA0171) ...................122...
  • Page 19 Table of Contents 6 Appendix ....................193 Revision History ......................194 6.1.1 PMMPR Software File Version 2.0xxx .................194 6.1.2 PMMPR Software File Version 2.01xx .................195 6.1.3 PMMPR Software File Version 3.0xxx .................196 Index......................197 Installation Manual...
  • Page 20 Table of Contents Installation Manual...
  • Page 21: System Outline

    Section 1 System Outline This section provides general information on the PBX, including the system capacity and specifications. Installation Manual...
  • Page 22: Basic System Construction

    The basic shelf contains an IPCMPR card for controlling the PBX. To use the system, install a power supply unit (PSU) in the PSU Slot and optional service cards in the basic shelf. KX-TDE100 KX-TDE200 Construction of the Basic Shelf PSU Slot...
  • Page 23: System Connection Diagram

    1.1.2 System Connection Diagram 1.1.2 System Connection Diagram *¹ Private ITSP IP Network Network Trunk (Telephone Company Lines) Analogue/BRI/PRI/T1/E1 Remote PC Pure IP-PBX Router *² (e.g., ADSL Modem) Batteries IP-PT IP Softphone, CA Client PC Fax Machine SIP Extension DSS Console Wireless Phone Printer IP-CS...
  • Page 24 1.1.2 System Connection Diagram LCOT4 LCOT4 CSLC16 (KX-TDA0183) (KX-TDA0183) (KX-TDA0177) MSLC16 LCOT16 (KX-TDA0175) (KX-TDA0181) Wireless Phone Fax Machine LCOT8 (KX-TDA0180) SLC16 (KX-TDA0174) CID/PAY8 (KX-TDA0189) SLC8 (KX-TDA0173) CID8 (KX-TDA0193) EXT-CID Analogue (KX-TDA0168) Trunk DID8 KX-DT300/ KX-DT300/ KX-DT346/ (KX-TDA0182) KX-T7600 KX-T7600 KX-DT343/ DLC16 E &...
  • Page 25: Optional Equipment

    Compliant with ITU-T G.729A and G.711 codec methods. To be mounted on the IPCMPR card. KX-TDA0103 L-Type Power Supply Unit Power Supply Unit for the KX-TDE200. Total (PSU-L) power output of 279 W. Safety Class 1 compliant. KX-TDA0104 M-Type Power Supply Unit...
  • Page 26 1.2.1 Optional Equipment Model No. Model Name Description KX-TDA0171 8-Port Digital Extension Card 8-port digital extension card for DPTs, DSS (DLC8) consoles, and PT-interface CSs. KX-TDA0172 16-Port Digital Extension Card 16-port digital extension card for DPTs, DSS (DLC16) consoles, and PT-interface CSs. KX-TDA0173 8-Port Single Line Telephone 8-port extension card for SLTs with 2 power...
  • Page 27 NI (North American standard ISDN protocol) compliant. KX-TDA0470 16-Channel VoIP Extension Card 16-channel VoIP extension card. Compliant with (IP-EXT16) Panasonic proprietary protocol, and ITU-T G. 729A and G.711 codec methods. KX-TDA0484 4-Channel VoIP Gateway Card 4-channel VoIP gateway card. Compliant with (IP-GW4E) VoIP H.323 V.2 protocol, and ITU-T G.729A, G.
  • Page 28: Specifications

    1.3.1 General Description 1.3 Specifications 1.3.1 General Description Control Bus Original bus (16-bit, 8 MHz, 10 megabytes per second) Communication Bus H.100 bus conformity (1024 time slots) Switching Non-blocking Power Input PSU-S 100 V AC to 130 V AC; 1.4 A/200 V AC to 240 V AC; 0.8 A; 50 Hz/60 Hz PSU-M 100 V AC to 130 V AC;...
  • Page 29 1-pair wire (D1, D2) Module 334 mm (W) ´ 390 mm (H) ´ 272 mm (D) Dimension KX-TDE100 430 mm (W) ´ 415 mm (H) ´ 276 mm (D) KX-TDE200 Weight (when fully KX-TDE100 Under 12 kg mounted) KX-TDE200 Under 16 kg...
  • Page 30: Characteristics

    1.3.2 Characteristics 1.3.2 Characteristics Terminal Equipment Loop Limit • PT: KX-DT300/KX-T7600 series DPT: 90 W; all other DPTs/APTs: 40 W • SLT: 600 W including set Doorphone: 20 W • • CS: 130 W; PT-interface CS: 65 W 15 000 W minimum Minimum Leakage Resistance Maximum Number of Extension for PT or SLT...
  • Page 31: System Capacity

    1.3.3 System Capacity Type and Maximum Number of Slots The PBX supports the following type and number of slots. Maximum Number Slot Type KX-TDE100 KX-TDE200 IPCMPR Card Slot Free Slot Virtual Trunk Slot Virtual Slot Virtual Extension Slot IPCMPR Card Slot and Free Slots...
  • Page 32 1.3.3 System Capacity Virtual Slots of the IPCMPR Card Virtual Trunk Virtual Slots Extension Slots IPCMPR Card Virtual Slots Maximum Optional Service Cards The following number of cards can be installed in the Free Slots or Virtual Slots of the PBX. Note •...
  • Page 33 1.3.3 System Capacity Cards Installed in Free Slots or Virtual Slots Maximum Number Card Type KX-TDE100 KX-TDE200 IPCMPR Trunk Card Virtual Trunk Card V-IPGW16 V-SIPGW16 Physical Trunk Card Total 6 Total 8 LCOT4 LCOT8 LCOT16 DID8 E&M8 BRI4 BRI8 PRI23...
  • Page 34 1.3.3 System Capacity Cards Mounted on Other Optional Service Cards Maximum Number Card Type Mounted on KX-TDE100 KX-TDE200 DSP16 DSP64 IPCMPR Card IPCMEC CID/PAY8 LCOT8 Card/LCOT16 Card CID8 EXT-CID SLC8 Card DPH4 DPH2 ECHO16 MSG4 OPB3 Card ESVM2 ESVM4 EIO4 Only 1 ECHO16 card can be mounted on each OPB3 card.
  • Page 35 1.3.3 System Capacity Type KX-TDE100 KX-TDE200 Extension (Virtual Extension Card) IP-PT and IP Softphone SIP Extension Only 49 virtual trunk/extension card channels can be in use at any one time (except for peer-to-peer calls for IP extensions). Note For non-peer-to-peer calls via the DSP card, calls cannot be made or received when all of the card’s resources are being used.
  • Page 36 1.3.3 System Capacity Maximum Terminal Equipment The following shows the number of each terminal equipment type supported by the PBX. Terminal Equipment Type KX-TDE100 KX-TDE200 Telephone KX-DT300/KX-T7600 series DPT KX-T7560/KX-T7565 DPT Other DPT IP-PT IP-PT (supported by IP-EXT16 card) IP-PT...
  • Page 37 1.3.3 System Capacity Note for KX-NT265 IP-PT users The supported card varies depending on the software version of your KX-NT265 IP-PT. To confirm the version, follow the procedure below: While starting up SP-PHONE SP-PHONE PROGRAM "AP Version". Select Select "Maintenance". "Version display".
  • Page 38 1.3.3 System Capacity PSU Capacity Each PSU supports a different load figure. PSU Type Maximum Load Figure PSU-S (for KX-TDE100 only) PSU-M PSU-L (for KX-TDE200 only) Calculation Example (KX-TDE200) Equipment Type Load Figure KX-T7600 series DPT 48 units Other DPT...
  • Page 39: Activation Key Installation

    Section 2 Activation Key Installation This section describes information on activation keys, including how to obtain an activation key and install it in the SD Memory Card. Installation Manual...
  • Page 40: Information About The Activation Keys

    2.1.1 Activation Keys 2.1 Information about the Activation Keys 2.1.1 Activation Keys To use IP trunks and IP telephones on a private IP network using the IPCMPR card or to upgrade the software for enhanced features, you need the appropriate activation keys. Activation Keys are provided via the DSP16/DSP64 card and optional activation key files.
  • Page 41 2.1.1 Activation Keys Supported IP Trunks/ Maximum Activation Key Type Description IP Telephones/CA Number Users Allows the use of CA Basic for 128 CA Basic 128users 128 users users. Allows the use of CA PRO for 1 user. CA Pro 1user 128 users Allows the use of CA PRO for 5 CA Pro 5users...
  • Page 42 2.1.1 Activation Keys Example: Preinstalled Activation Keys in the DSP16 Card Additional Activation Keys in the SD Memory Card (Activation Key Files) When the number of preinstalled activation keys on the DSP16/DSP64 card is not enough for the desired configuration or when you wish to use enhanced features, additional activation keys in the form of activation key files can be installed on the SD Memory Card.
  • Page 43 2.1.1 Activation Keys Maximum Number/Supported IP Telephones Model No. Activation Key Type with DSP16 with DSP64 KX-NCS4701 1 SIP Extension KX-NCS4704 4 SIP Extension 128 SIP 128 SIP Extensions Extensions KX-NCS4708 8 SIP Extension KX-NCS4716 16 SIP Extension Activation Keys for CA Users Model No.
  • Page 44 2.1.1 Activation Keys Activation Key Installation Example The following shows an example of when using 16 H.323 trunks, 16 SIP trunks, 32 IP-PTs, 32 IP softphones, and 64 SIP Extensions on a private IP network using the IPCMPR card. Virtual Trunk Virtual Extension Slots Slots...
  • Page 45: Activation Key Code And Key Management System

    2.1.2 Activation Key Code and Key Management System 2.1.2 Activation Key Code and Key Management System To obtain additional activation keys, you need to purchase the appropriate activation key codes and access the Key Management System. You can download the activation keys as an activation key file from the Key Management System.
  • Page 46: Activation Key File

    2.1.3 Activation Key File 2.1.3 Activation Key File The corresponding number of IP trunks and IP telephones or enhanced features can be activated by installing the downloaded activation key file(s) in the SD Memory Card of the IPCMPR card using the Maintenance Console.
  • Page 47: Installation

    Section 3 Installation This section describes the procedures to install the PBX. Detailed instructions for planning the installation site, installing the shelves and optional service cards, and cabling of peripheral equipment are provided. Further information on system expansion and peripheral equipment installation is included.
  • Page 48: Before Installation

    Use caution when installing or modifying telephone lines. Installation Precautions This set is made for wall mounting (KX-TDE100/KX-TDE200) or floor standing (KX-TDE200 only), and should be installed in a location where it is accessible for inspections and maintenance. To prevent malfunction, noise, or discolouration, follow the instructions below:...
  • Page 49 3.1.1 Before Installation Wiring Precautions Be sure to follow these instructions when wiring the unit: WARNING • Do not run unshielded telephone cables near AC power cables, computer cables, AC power sources, etc. When running cables near other noise-generating devices or cables, use shielded telephone cables or shield the telephone cables with metal tubing.
  • Page 50: Installation Of The Pbx

    3.2.1 Unpacking 3.2 Installation of the PBX 3.2.1 Unpacking Unpack the box and check the items below: KX-TDE100 KX-TDE200 Main Unit Ferrite Core (for the IPCMPR card) AC Cord with a Ferrite Core Metal Bracket Screw A Screw B (Black)
  • Page 51: Names And Locations

    3.2.2 Names and Locations 3.2.2 Names and Locations Inside View KX-TDE100 KX-TDE200 RUN Indicator ALARM Indicator MNT Port LAN Port PSU Slot Null Slot (not available for any optional service card) Free Slots 1 to 6 (from the left) IPCMPR Card Slot...
  • Page 52: Opening/Closing The

    3.2.3 Opening/Closing the Front Cover 3.2.3 Opening/Closing the Front Cover Opening the Front Cover Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw cover. Screw Cover Turn the screw anticlockwise to loosen. Slide the front cover to the right until it stops, then lift the front cover.
  • Page 53 3.2.3 Opening/Closing the Front Cover Closing the Front Cover Hook the front cover onto the shelf (line up the protrusions on the cover with the receptacles on the shelf). Then slide the front cover to the left until it locks. Turn the screw clockwise to tighten.
  • Page 54: Installing/Replacing The Power Supply Unit

    Upper: 200 V AC to 240 V AC 1.4 A KX-TDE200) Lower: 100 V AC to 130 V AC 5.1 A PSU-L (for KX-TDE200) Upper: 200 V AC to 240 V AC 2.55 A PSU-S PSU-M/PSU-L Battery Switch Battery Switch...
  • Page 55 3.2.4 Installing/Replacing the Power Supply Unit Note • For details about frame earth connection, refer to "3.2.5 Frame Earth Connection". • For details about backup batteries connection, refer to "3.2.6 Backup Battery Connection". The following procedures are for installing or replacing a PSU only. Do not replace or remove the PSU for any other purpose.
  • Page 56 3.2.4 Installing/Replacing the Power Supply Unit Turn the 4 screws clockwise, in the order indicated by the numbers 1 to 4, to fix the PSU. Screws Replacing the Power Supply Unit Unplug the AC power cord and Back-up Battery Cable. Turn the 4 screws anticlockwise to loosen them.
  • Page 57 3.2.4 Installing/Replacing the Power Supply Unit Pull the release lever in the direction of the arrow to disconnect the PSU from the back board. Back Board Release Lever Replace the PSU. New PSU Current PSU Follow the steps in "Installing the Power Supply Unit". Installation Manual...
  • Page 58: Frame Earth Connection

    3.2.5 Frame Earth Connection 3.2.5 Frame Earth Connection Loosen the screw. Screw Insert an earthing wire (user-supplied). Tighten the screw. Connect the earthing wire to earth. Earthing wire To earth WARNING • Proper earthing (connection to earth) is very important to reduce the risk to the user of electrocution or to protect the PBX from the bad effects of external noise in the case of a lightning strike.
  • Page 59: Backup Battery Connection

    3.2.6 Backup Battery Connection 3.2.6 Backup Battery Connection The backup batteries and Back-up Battery Cable provide a backup power supply to allow full use of the PBX in the event of a power failure. In case of power failure, the backup batteries automatically maintain the power to the PBX without interruption.
  • Page 60 3.2.6 Backup Battery Connection Connecting Backup Batteries Turn off the battery switch on the PSU. Connect the Back-up Battery Cable to a set of 3 identical batteries. Battery Switch Battery Connector Back-up Battery Cable Fuse Black Backup Batteries (VRLA 12 V DC x 3) Installation Manual...
  • Page 61: Installing/Removing The Optional Service Cards

    3.2.7 Installing/Removing the Optional Service Cards 3.2.7 Installing/Removing the Optional Service Cards CAUTION • To protect the back board from static electricity, do not touch parts on the back board in the main unit and on the optional service cards. To discharge static electricity, touch ground or wear an earthing strap.
  • Page 62 3.2.7 Installing/Removing the Optional Service Cards Turn the 2 screws clockwise to fix the card in place. Screws Note Make sure the screws are tightened to earth the card securely. Installation Manual...
  • Page 63 3.2.7 Installing/Removing the Optional Service Cards Covering the Blank Slots Be sure to cover each slot in which no optional service card is installed by using a Blank Slot Cover. CAUTION Failure to install the Blank Slot Cover may cause electromagnetic interference. Installation Manual...
  • Page 64 3.2.7 Installing/Removing the Optional Service Cards Handling of the Cables When cables are connected to the PBX, run the cables to either the right or the left and then towards the back of the shelf as shown below. Note For safety reasons, do not stretch, bend, or pinch the AC power cord. Installation Manual...
  • Page 65 3.2.7 Installing/Removing the Optional Service Cards Removing the Optional Service Cards Turn the 2 screws anticlockwise to loosen them. Screws Pull the release lever in the direction of the arrow to disconnect the card from the back board. Pull the card from the shelf to remove it.
  • Page 66: Types Of Connectors

    3.2.8 Types of Connectors 3.2.8 Types of Connectors Connector Type Pin Number Used for • DHLC8 (KX-TDA0170) RJ11 • SLC8 (KX-TDA0173) • SLC16 (KX-TDA0174) • MSLC16 (KX-TDA0175) • CSLC16 (KX-TDA0177) • LCOT8 (KX-TDA0180) • LCOT16 (KX-TDA0181) • LCOT4 (KX-TDA0183) (Twisted pair cable) •...
  • Page 67 3.2.8 Types of Connectors Connector Type Pin Number Used for • DPH4 (KX-TDA0161) 10-pin 8-pin • DPH2 (KX-TDA0162) Terminal Terminal • EIO4 (KX-TDA0164) Block Block • Basic Shelf RS-232C (Shielded cable) • IPCMPR Mini Plug Installation Manual...
  • Page 68: Attaching A Ferrite Core

    3.2.9 Attaching a Ferrite Core 3.2.9 Attaching a Ferrite Core A ferrite core must be attached when: • an RJ45 connector is connected to an IPCMPR, T1, E1, PRI, BRI, IP-GW16 or IP-EXT16 cards, or • an Amphenol connector is connected to an extension card. Note In Canada, the ferrite core is not necessarily required for the T1 and PRI23 cards.
  • Page 69 3.2.9 Attaching a Ferrite Core For a BRI Card Attach the ferrite core, then close the case of the ferrite core. Attach the ferrite core as close to the card’s connector as possible. The ferrite core is included with the card. When only 1 or 2 cables are used for connection, wrap the cable(s) once around the ferrite core.
  • Page 70 3.2.9 Attaching a Ferrite Core Attaching to an Amphenol Connector For Extension Cards Pass the cable through the ferrite core, then close the case of the ferrite core. Attach the ferrite core 3 cm away from the connector. The ferrite core is included with the card. 3 cm If you need to open the ferrite core, use a flathead screwdriver to unlatch the case of the ferrite core.
  • Page 71: Fastening An Amphenol Connector

    3.2.10 Fastening an Amphenol Connector 3.2.10 Fastening an Amphenol Connector An Amphenol 57JE-type connector is used on some of the optional service cards. To connect an Amphenol connector, use the spring latch or screw to fix the upper part and use Velcro® tape to fix the lower part of the connector.
  • Page 72 3.2.10 Fastening an Amphenol Connector Amphenol Connector Pin Assignment Chart Below is an Amphenol connector pin assignment chart for all optional service cards that use the Amphenol connector. For more details, refer to the appropriate section in "3.5 Information about the Physical Trunk Cards"...
  • Page 73: Wall Mounting (Kx-Tde200)

    3.2.11 Wall Mounting (KX-TDE200) 3.2.11 Wall Mounting (KX-TDE200) WARNING • Make sure that the wall that the shelf will be attached to is strong enough to support the shelf. If not, it is necessary for the wall to be reinforced.
  • Page 74 3.2.11 Wall Mounting (KX-TDE200) Install 4 anchor plugs in the wall, using the metal bracket as a template. Fix the metal bracket with 4 screws (A). Anchor Plug Hammer W a ll Anchor Plug 8 mm Metal Bracket 30 mm...
  • Page 75: Wall Mounting (Kx-Tde100)

    3.2.12 Wall Mounting (KX-TDE100) 3.2.12 Wall Mounting (KX-TDE100) WARNING • Make sure that the wall that the shelf will be attached to is strong enough to support the shelf. If not, it is necessary for the wall to be reinforced. •...
  • Page 76 3.2.12 Wall Mounting (KX-TDE100) Install 3 anchor plugs in the wall, using the metal bracket as a template. Fix the metal bracket with 3 screws (A). Anchor Plug Hammer Anchor Plug 8 mm W a ll Metal Bracket 30 mm Screw (A) Screw (A) Metal Bracket...
  • Page 77: Floor Standing (Kx-Tde200 Only)

    3.2.13 Floor Standing (KX-TDE200 Only) 3.2.13 Floor Standing (KX-TDE200 Only) WARNING Be careful not to drop any components. Dropping components may damage them or cause an injury. CAUTION • Do not block the openings of the shelf. Allow space of at least 20 cm above and 10 cm at the sides of the shelf.
  • Page 78 3.2.13 Floor Standing (KX-TDE200 Only) Lift the shelf, attach it to the metal bracket, slide it backwards until it locks, and retain it with 2 screws (B). FRONT Screws (B) Metal Bracket Fix the front cover on the shelf (refer to "3.2.3 Opening/Closing the Front Cover").
  • Page 79: Surge Protector Installation

    3.2.14 Surge Protector Installation 3.2.14 Surge Protector Installation CAUTION Performing surge protection is essential. Make sure to follow the instructions in this section. Overview A massive electrical surge can be caused if lightning strikes a telephone cable 10 m above ground, or if a telephone line comes into contact with a power line.
  • Page 80 3.2.14 Surge Protector Installation Outside Installation (Main Building) Surge Protector Trunk (Another Building) Trunk Extn. PT-interface CS Terminal Board Surge Extn. Protector Extn. Extn. PT-interface CS Earth Extn.: Extension Line If you install an extension outside of the building, the following precautions are recommended: Install the extension wire underground.
  • Page 81 3.2.14 Surge Protector Installation Connect the earth rod to the surge protector using an earthing wire with a cross-sectional area of at least 1.3 mm Bury the earth rod near the protector. The earthing wire should be as short as possible. The earthing wire should run straight to the earth rod.
  • Page 82: Information About The Main Processing Card

    3.3.1 IPCMPR Card 3.3 Information about the Main Processing Card 3.3.1 IPCMPR Card Function The IPCMPR card is the preinstalled main processing card with built-in ESVM card feature (2-channel) and an Activation Key for CA Basic for 10 Users. The Virtual Cards (trunk/extension) can be installed in Virtual Slots of the IPCMPR card and can be activated with the activation keys.
  • Page 83 To prevent data leakage, render the SD Memory Card physically unusable before disposal. Notice • Some built-in ESVM card features are not supported for KX-TDE100/KX-TDE200 PBXs released with MPR software version 2.01 or earlier: – The Music on Hold feature is not recommended to be used with the built-in ESVM card feature.
  • Page 84 3.3.1 IPCMPR Card LED Indications Indication Colour Description BATT ALARM Battery alarm indication • OFF: Normal ON: Alarm SD ACCESS Green SD memory card status • ON: Accessing 10BASE-T/100BASE-TX 2 LINK Green Link status indication • OFF: Off-line • ON: Linked normally •...
  • Page 85: Dsp16 Card (Kx-Tde0110) And Dsp64 Card (Kx-Tde0111)

    3.3.2 DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111) 3.3.2 DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111) Function DSP16: 16-channel digital signal processor card with a 4-Channel IP Trunk activation key and a 8-Channel IP Proprietary Telephone activation key preinstalled. Compliant with ITU-T G. 729A and G.711 codec methods.
  • Page 86 3.3.2 DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111) • When installing the DSP16 or DSP64 card, hold down the shaded areas of the card to connect it firmly. Installation Manual...
  • Page 87: Ipcmec Card (Kx-Tde0105)

    3.3.3 IPCMEC Card (KX-TDE0105) 3.3.3 IPCMEC Card (KX-TDE0105) Function Memory expansion card to increase system data storage space. To be mounted on the IPCMPR card. IPCMPR Card inside IPCMEC Card Screw Accessories and User-supplied Items Accessories (included): Screws ´ 2 User-supplied (not included): none CAUTION •...
  • Page 88: Rmt Card (Kx-Tda0196)

    3.3.4 RMT Card (KX-TDA0196) 3.3.4 RMT Card (KX-TDA0196) Function Analogue modem card for remote communication with the PBX. ITU-T V.90 support. To be mounted on the IPCMPR card. IPCMPR Card inside RMT Card Screw Accessories and User-supplied Items Accessories (included): Screws ´ 2 User-supplied (not included): none Installation Manual...
  • Page 89: Information About The Virtual Cards

    3261, 3262, 3264, 3311, 3581, 3960 and 4028 protocols, and ITU-T G.729AB and G.711 codec methods. Also supports T. 38 protocol. Virtual 32-Channel VoIP Extension Virtual Card for 32 VoIP extensions. Compliant with Panasonic Card (V-IPEXT32) proprietary protocol, and ITU-T G.729A, G.711 and G.722 codec methods.
  • Page 90: Information About The Physical Trunk Cards

    3.5.1 LCOT4 Card (KX-TDA0183), LCOT8 Card (KX-TDA0180), and LCOT16 Card (KX-TDA0181) 3.5 Information about the Physical Trunk Cards 3.5.1 LCOT4 Card (KX-TDA0183), LCOT8 Card (KX-TDA0180), and LCOT16 Card (KX-TDA0181) Function LCOT4: 4-port analogue trunk card with 2 power failure transfer (PFT) ports. LCOT8: 8-port analogue trunk card with 2 power failure transfer (PFT) ports.
  • Page 91 3.5.1 LCOT4 Card (KX-TDA0183), LCOT8 Card (KX-TDA0180), and LCOT16 Card (KX-TDA0181) Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Ring port 1 Tip port 1 Ring port 2 Tip port 2 Ring port 3 Tip port 3 Ring port 4 Tip port 4 Ring port 5 Tip port 5...
  • Page 92: Did8 Card (Kx-Tda0182)

    3.5.2 DID8 Card (KX-TDA0182) 3.5.2 DID8 Card (KX-TDA0182) Function 8-port DID trunk card. Amphenol To DID line Accessories and User-supplied Items Accessories (included): Screws ´ 2 User-supplied (not included): Amphenol connector Note • To connect the Amphenol connector, refer to "3.2.10 Fastening an Amphenol Connector". •...
  • Page 93 3.5.2 DID8 Card (KX-TDA0182) Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Ring port 1 Tip port 1 Ring port 2 Tip port 2 Ring port 3 Tip port 3 Ring port 4 Tip port 4 Ring port 5 Tip port 5 Ring port 6 Tip port 6...
  • Page 94: Cid/Pay8 Card (Kx-Tda0189)

    3.5.3 CID/PAY8 Card (KX-TDA0189) 3.5.3 CID/PAY8 Card (KX-TDA0189) Function 8-port Caller ID signal type FSK/FSK (with Call Waiting Caller ID [Visual Caller ID])/DTMF, and 8-port Pay Tone Service (12 kHz/16 kHz). To be mounted on the LCOT8/LCOT16 cards. Set all DIP switches for ports 09-16 at "OFF"...
  • Page 95: Cid8 Card (Kx-Tda0193)

    3.5.4 CID8 Card (KX-TDA0193) 3.5.4 CID8 Card (KX-TDA0193) Function 8-port Caller ID signal type FSK/FSK (with Call Waiting Caller ID [Visual Caller ID])/DTMF. To be mounted on the LCOT8/LCOT16 cards. LCOT16 card only inside CID8 Card Screw S W 1 Accessories and User-supplied Items Accessories (included): Screws ´...
  • Page 96: E&M8 Card (Kx-Tda0184)

    3.5.5 E&M8 Card (KX-TDA0184) 3.5.5 E&M8 Card (KX-TDA0184) Function 8-port E & M (TIE) trunk card. Type 5 support. Amphenol To terminal board from the E & M (TIE) line Accessories and User-supplied Items Accessories (included): Screws ´ 2 User-supplied (not included): Amphenol connector Note •...
  • Page 97 3.5.5 E&M8 Card (KX-TDA0184) Signal Name Function Signal Name Function Tip 1 port 3 Ring 1 port 3 E line port 3 M line port 3 Tip port 4 Ring port 4 Tip 1 port 4 Ring 1 port 4 E line port 4 M line port 4 Tip port 5...
  • Page 98: T1 Card (Kx-Tda0187)

    3.5.6 T1 Card (KX-TDA0187) 3.5.6 T1 Card (KX-TDA0187) Function 1-port T1 trunk card. EIA/TIA standard compliant. LEDs RJ45 To NT1 / Extension Accessories and User-supplied Items Accessories (included): Ferrite core ´ 1 User-supplied (not included): RJ45 connector CAUTION • When connecting this optional service card to the trunk, connect through NT1; do not connect to the trunk directly.
  • Page 99 3.5.6 T1 Card (KX-TDA0187) Pin Assignments RJ45 Connector for Trunk Use Signal Name Level [V] Function Receive data (+) Receive data (-) Reserved – – Transmit data (-) Transmit data (+) Reserved – – RJ45 Connector for Extension Use Signal Name Level [V] Function Transmit data (-)
  • Page 100 3.5.6 T1 Card (KX-TDA0187) Indication Colour Description SYNC Green Synchronisation status indication • OFF: Not synchronised • ON: Synchronised • Flashing (60 times per minute): Synchronised (Clock Master) Maximum Cabling Distance of Extension Connection The maximum length of the extension cable that connects the T1 cards is shown below: Diameter Maximum Distance 0.5 mm:...
  • Page 101: E1 Card (Kx-Tda0188)

    3.5.7 E1 Card (KX-TDA0188) 3.5.7 E1 Card (KX-TDA0188) Function 1-port E1 trunk card. ITU-T standard compliant. LEDs RJ45 BNC (TX) outer conductor J 3 0 8 J 3 0 8 To NT1/Extension For Frame For Frame To NT1/Extension Ground Open Ground Short For RJ45 BNC (TX)
  • Page 102 3.5.7 E1 Card (KX-TDA0188) Switch Settings Switch Type Usage and Status Definition Select 120 W (default) or 75 W to match the connector type to be Termination Slide used. Slide When using an RJ45 connector, select A (default) for trunk or B for extension use.
  • Page 103 3.5.7 E1 Card (KX-TDA0188) BNC (coaxial) Connector (RX) Signal Name Level [V] Function Receive data (-) Receive data (+) LED Indications Indication Colour Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) •...
  • Page 104: Bri4 Card (Kx-Tda0284) And Bri8 Card (Kx-Tda0288)

    3.5.8 BRI4 Card (KX-TDA0284) and BRI8 Card (KX-TDA0288) 3.5.8 BRI4 Card (KX-TDA0284) and BRI8 Card (KX-TDA0288) Function BRI4: 4-port ISDN Basic Rate Interface card with 1 power failure transfer port. EURO-ISDN/ETSI compliant. BRI8: 8-port ISDN Basic Rate Interface card with 1 power failure transfer port. EURO-ISDN/ETSI compliant.
  • Page 105 3.5.8 BRI4 Card (KX-TDA0284) and BRI8 Card (KX-TDA0288) Switch Settings Switch Type Usage and Status Definition Slide Select A (default) for trunk or B for extension use. Pin Assignments RJ45 Connector for Trunk Use Signal Name Level [V] Function Reserved –...
  • Page 106 3.5.8 BRI4 Card (KX-TDA0284) and BRI8 Card (KX-TDA0288) Indication Colour Description LINE 8 Green Line status indication (LINE 1 to LINE 8): LINE 7 Refer to "LINE LED Pattern" below for details. LINE 6 Note LINE 5 LINE 5 to LINE 8 are for BRI8 card only. LINE 4 LINE 3 LINE 2...
  • Page 107 3.5.8 BRI4 Card (KX-TDA0284) and BRI8 Card (KX-TDA0288) Maximum Cabling Distance of S0 Bus Connection The maximum length of the extension cable that connects the PBX and the ISDN terminal equipment (TE) is shown below: CAT 5: Under 1000 m Point-to-Point CAT 5: Under 150 m Point-to-Multipoint...
  • Page 108: Pri30 Card (Kx-Tda0290Ce/Kx-Tda0290Cj)

    3.5.9 PRI30 Card (KX-TDA0290CE/KX-TDA0290CJ) 3.5.9 PRI30 Card (KX-TDA0290CE/KX-TDA0290CJ) Function 1-port ISDN Primary Rate Interface card (30B channels). EURO-ISDN/ETSI compliant. LEDs RJ45 To NT1 / Extension To NT1/Extension For RJ45 BNC (TX) BNC (RX) 120Ω 120Ω For BNC 75Ω 75Ω Accessories and User-supplied Items Accessories (included): Ferrite core ´...
  • Page 109 3.5.9 PRI30 Card (KX-TDA0290CE/KX-TDA0290CJ) Switch Settings Switch Type Usage and Status Definition Select 120 W (default) or 75 W to match the connector type to be Termination Slide used. Slide When using an RJ45 connector, select A (default) for trunk or B for extension use.
  • Page 110 3.5.9 PRI30 Card (KX-TDA0290CE/KX-TDA0290CJ) LED Indications Indication Colour Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
  • Page 111: Pri23 Card (Kx-Tda0290)

    3.5.10 PRI23 Card (KX-TDA0290) 3.5.10 PRI23 Card (KX-TDA0290) Function 1-port ISDN Primary Rate Interface card (23B channels). NI (North American standard ISDN protocol) compliant. LEDs RJ45 To NT1/ Extension Accessories and User-supplied Items Accessories (included): Ferrite core ´ 1 User-supplied (not included): RJ45 connector CAUTION •...
  • Page 112 3.5.10 PRI23 Card (KX-TDA0290) Pin Assignments RJ45 Connector for Trunk Use Signal Name Level [V] Function Receive data (+) Receive data (-) Reserved – – Transmit data (-) Transmit data (+) Reserved – – RJ45 Connector for Extension Use Signal Name Level [V] Function Transmit data (-)
  • Page 113 3.5.10 PRI23 Card (KX-TDA0290) Indication Colour Description SYNC Green Synchronisation status indication • OFF: Not synchronised • ON: Synchronised • Flashing (60 times per minute): Synchronised (Clock Master) D-LINK Green Data link status indication • OFF: Not established • ON: Established Maximum Cabling Distance of Extension Connection The maximum length of the extension cable that connects the PRI23 cards is shown below: Diameter...
  • Page 114: Ip-Gw4E Card (Kx-Tda0484)

    3.5.11 IP-GW4E Card (KX-TDA0484) 3.5.11 IP-GW4E Card (KX-TDA0484) Function 4-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729A, G.723.1 and G. 711 codec methods. LEDs RJ45 (10BASE-T/100BASE-TX) To private IP network Accessories and User-supplied Items Accessories (included): CD-ROM (including documentation for web programming) ´ 1 User-supplied (not included): RJ45 connector Note •...
  • Page 115 3.5.11 IP-GW4E Card (KX-TDA0484) LED Indications Indication Colour Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
  • Page 116: Ip-Gw16 Card (Kx-Tda0490)

    3.5.12 IP-GW16 Card (KX-TDA0490) 3.5.12 IP-GW16 Card (KX-TDA0490) Function 16-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729A, G.723.1 and G. 711 codec methods. LEDs RJ45 (10BASE-T/100BASE-TX Full Duplex) To private IP network Accessories and User-supplied Items Accessories (included): Ferrite core ´...
  • Page 117 3.5.12 IP-GW16 Card (KX-TDA0490) LED Indications Indication Colour Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
  • Page 118: Information About The Physical Extension Cards

    3.6.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) 3.6 Information about the Physical Extension Cards 3.6.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) Function CSIF4: 4-port CS interface card for 4 CSs. CSIF8: 8-port CS interface card for 8 CSs. RJ45 (LINE 1 to LINE 8) To CS...
  • Page 119 3.6.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) Pin Assignments RJ45 Connector Signal Name Function Reserved – Data port (High) POWH Power (High) POWL Power (Low) Data port (Low) Reserved – LED Indications Indication Colour Description CARD STATUS Green/Red Card status indication •...
  • Page 120: Dhlc8 Card (Kx-Tda0170)

    3.6.2 DHLC8 Card (KX-TDA0170) 3.6.2 DHLC8 Card (KX-TDA0170) Function 8-port digital hybrid extension card for DPTs, APTs, SLTs, DSS consoles, and PT-interface CSs, with 2 power failure transfer (PFT) ports. Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws ´ 2, Ferrite core ´ 1 User-supplied (not included): Amphenol connector Note •...
  • Page 121 3.6.2 DHLC8 Card (KX-TDA0170) Signal Signal Name Function Function Name PT Data port 3 PT Data port 3 (Low) (High) Reserved – Reserved – SLT Ring port 4 SLT Tip port 4 PT Data port 4 PT Data port 4 (Low) (High) Reserved...
  • Page 122: Dlc8 Card (Kx-Tda0171)

    3.6.3 DLC8 Card (KX-TDA0171) 3.6.3 DLC8 Card (KX-TDA0171) Function 8-port digital extension card for DPTs, DSS consoles, and PT-interface CSs. Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws ´ 2, Ferrite core ´ 1 User-supplied (not included): Amphenol connector Note •...
  • Page 123 3.6.3 DLC8 Card (KX-TDA0171) Signal Signal Name Function Function Name Data port 5 (Low) Data port 5 (High) 15-16 Reserved – 40-41 Reserved – Data port 6 (Low) Data port 6 (High) 18-19 Reserved – 43-44 Reserved – Data port 7 (Low) Data port 7 (High) 21-22 Reserved...
  • Page 124: Dlc16 Card (Kx-Tda0172)

    3.6.4 DLC16 Card (KX-TDA0172) 3.6.4 DLC16 Card (KX-TDA0172) Function 16-port digital extension card for DPTs, DSS consoles, and PT-interface CSs. Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws ´ 2, Ferrite core ´ 1 User-supplied (not included): Amphenol connector Note •...
  • Page 125 3.6.4 DLC16 Card (KX-TDA0172) Signal Signal Name Function Function Name Data port 10 Data port 10 (Low) (High) Data port 11 Data port 11 (Low) (High) Data port 12 Data port 12 (Low) (High) Data port 13 Data port 13 (Low) (High) Data port 14...
  • Page 126: Slc8 Card (Kx-Tda0173)

    3.6.5 SLC8 Card (KX-TDA0173) 3.6.5 SLC8 Card (KX-TDA0173) Function 8-port extension card for SLTs with 2 power failure transfer (PFT) ports. Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws ´ 2, Ferrite core ´ 1 User-supplied (not included): Amphenol connector Note •...
  • Page 127 3.6.5 SLC8 Card (KX-TDA0173) Pin Assignments Amphenol Connector Signal Signal Name Function Function Name Ring port 1 Tip port 1 Reserved – 27-28 Reserved – Ring port 2 Tip port 2 Reserved – 30-31 Reserved – Ring port 3 Tip port 3 Reserved –...
  • Page 128: Ext-Cid Card (Kx-Tda0168)

    3.6.6 EXT-CID Card (KX-TDA0168) 3.6.6 EXT-CID Card (KX-TDA0168) Function Sends Caller ID signals to extension ports. To be mounted on the SLC8 card only. inside SLC8 Card Screw EXT-CID Card Accessories and User-supplied Items Accessories (included): Screws ´ 2 User-supplied (not included): none Installation Manual...
  • Page 129: Slc16 Card (Kx-Tda0174), Mslc16 Card (Kx-Tda0175), And Cslc16 Card (Kx-Tda0177)

    Accessories (included): Screws ´ 2, Ferrite core ´ 1 User-supplied (not included): Amphenol connector Note • Panasonic SLT with Message Waiting Lamp (e.g., KX-T7710) is recommended for connection to the MSLC16 card. • Attach the included ferrite core to the cable. Refer to "3.2.9 Attaching a Ferrite Core".
  • Page 130 3.6.7 SLC16 Card (KX-TDA0174), MSLC16 Card (KX-TDA0175), and CSLC16 Card (KX-TDA0177) Pin Assignments Amphenol Connector Signal Signal Name Function Function Name Ring port 1 Tip port 1 Ring port 2 Tip port 2 Ring port 3 Tip port 3 Ring port 4 Tip port 4 Ring port 5 Tip port 5...
  • Page 131: Ip-Ext16 Card (Kx-Tda0470)

    3.6.8 IP-EXT16 Card (KX-TDA0470) 3.6.8 IP-EXT16 Card (KX-TDA0470) Function 16-channel VoIP extension card. Compliant with Panasonic proprietary protocol, and ITU-T G.729A and G. 711 codec methods. LEDs RJ45 (10BASE-T/100BASE-TX Full Duplex) To LAN Accessories and User-supplied Items Accessories (included): Ferrite core ´ 1...
  • Page 132 If the LINK indicator is OFF, the ONLINE indicator will also be OFF. ALARM Alarm indication • OFF: Normal • ON: Alarm VoIP BUSY Green Panasonic proprietary VoIP protocol process indication • OFF: VoIP process inactive • ON: VoIP process active LINK Green Link status indication •...
  • Page 133: Information About The Other Physical Cards

    3.7.1 OPB3 Card (KX-TDA0190) 3.7 Information about the Other Physical Cards 3.7.1 OPB3 Card (KX-TDA0190) Function Optional 3-slot base card for mounting a maximum of 3 option cards from the following: • DPH4 card • DPH2 card • EIO4 card •...
  • Page 134: Dph4 Card (Kx-Tda0161)

    3.7.2 DPH4 Card (KX-TDA0161) 3.7.2 DPH4 Card (KX-TDA0161) Function 4-port doorphone card for 4 doorphones and 4 door openers. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings. DPH4 Card OPB3 Card 8-pin Screw 10-pin Accessories and User-supplied Items Accessories (included): Screws ´...
  • Page 135 3.7.2 DPH4 Card (KX-TDA0161) Pin Assignments 8-pin Terminal Block Signal Name Function Doorphone 4 transmit com4 Doorphone 4 receive Doorphone 3 transmit com3 Doorphone 3 receive Doorphone 2 transmit com2 Doorphone 2 receive Doorphone 1 transmit com1 Doorphone 1 receive 10-pin Terminal Block Signal Name Function...
  • Page 136: Dph2 Card (Kx-Tda0162)

    3.7.3 DPH2 Card (KX-TDA0162) 3.7.3 DPH2 Card (KX-TDA0162) Function 2-port doorphone card for 2 German-type doorphones and 2 door openers. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings. DPH2 Card OPB3 Card 8-pin Screw 10-pin Accessories and User-supplied Items...
  • Page 137 3.7.3 DPH2 Card (KX-TDA0162) Pin Assignments 8-pin Terminal Block Proprietary Standard Function Signal Name Signal Name Path_2b b (2) Doorphone 2 transmit Path_2a a (2) Doorphone 2 receive Call_2b RT b (2) Doorphone 2 call button Call_2a RT a (2) Doorphone 2 call button com Path_1b b (1)
  • Page 138 3.7.3 DPH2 Card (KX-TDA0162) Connection Diagram for German-type Doorphones and Door Openers German-type Doorphone 2 BL: Light RT: Call Button OP: Door Opener Connection Terminal Door Opener 2 DC: Doorphone Current Supply Control Terminal Path: Doorphone Call Path L O U B Call_2b Call_2a : Speaker...
  • Page 139: Eio4 Card (Kx-Tda0164)

    3.7.4 EIO4 Card (KX-TDA0164) 3.7.4 EIO4 Card (KX-TDA0164) Function 4-port external input/output card. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings. EIO4 Card OPB3 Card 8-pin Screw 10-pin Accessories and User-supplied Items Accessories (included): Screws ´ 3, 10-pin terminal block ´ 1, 8-pin terminal block ´ 1 User-supplied (not included): Copper wire Note For details about connection to external sensors and external relays, refer to "3.9.1 Connection of...
  • Page 140 3.7.4 EIO4 Card (KX-TDA0164) Pin Assignments 8-pin Terminal Block Signal Name Function Control 4 Control 4 com Control 3 Control 3 com Control 2 Control 2 com Control 1 Control 1 com 10-pin Terminal Block Signal Name Function Reserved – OP4b Opener 4 OP4a...
  • Page 141: External Sensor

    3.7.4 EIO4 Card (KX-TDA0164) External Sensor Power to the external sensor is provided from the EIO4 card and must be grounded through the EIO4 card as indicated in the diagram below. A pair of "sensor" and "common" lines are connected to the EIO4 card for each external sensor.
  • Page 142: Echo16 Card (Kx-Tda0166)

    3.7.5 ECHO16 Card (KX-TDA0166) 3.7.5 ECHO16 Card (KX-TDA0166) Function 16-channel card for echo cancellation during conferences. To be mounted on the OPB3 card. OPB3 Card inside ECHO16 Card Screw Accessories and User-supplied Items Accessories (included): Screws ´ 3 User-supplied (not included): none Note To establish a conference call involving 6 to 8 parties, install an ECHO16 card and enable echo cancellation for conferences using the Maintenance Console.
  • Page 143: Msg4 Card (Kx-Tda0191)

    3.7.6 MSG4 Card (KX-TDA0191) 3.7.6 MSG4 Card (KX-TDA0191) Function 4-channel message card. To be mounted on the OPB3 card. OPB3 Card inside MSG4 Card Screw Accessories and User-supplied Items Accessories (included): Screws ´ 3 User-supplied (not included): none Installation Manual...
  • Page 144: Esvm2 Card (Kx-Tda0192) And Esvm4 Card (Kx-Tda0194)

    3.7.7 ESVM2 Card (KX-TDA0192) and ESVM4 Card (KX-TDA0194) 3.7.7 ESVM2 Card (KX-TDA0192) and ESVM4 Card (KX-TDA0194) Function ESVM2: 2-channel simplified voice message card for Built-in Simplified Voice Message feature. Also supports MSG card features. To be mounted on the OPB3 card. ESVM4: 4-channel simplified voice message card for Built-in Simplified Voice Message feature.
  • Page 145: Connection Of Extensions

    3.8.1 Maximum Cabling Distances of the Extension Wiring (Twisted Cable) 3.8 Connection of Extensions 3.8.1 Maximum Cabling Distances of the Extension Wiring (Twisted Cable) Cable Maximum Distance ø 0.4 mm: 222 m PT-interface CS ø 0.5 mm: 347 m ø 0.6 mm: 500 m CAT 5: 347 m...
  • Page 146 3.8.1 Maximum Cabling Distances of the Extension Wiring (Twisted Cable) "ü" indicates that the extension card supports the terminal. Installation Manual...
  • Page 147: Parallel Connection Of The Extensions

    3.8.2 Parallel Connection of the Extensions 3.8.2 Parallel Connection of the Extensions Any SLT can be connected in parallel with an APT or a DPT as follows. Note In addition to an SLT, an answering machine, a fax machine or a modem (PC) can be connected in parallel with an APT or a DPT.
  • Page 148 3.8.2 Parallel Connection of the Extensions With DPT Parallel mode or eXtra Device Port (XDP) mode can be selected through system programming. If XDP mode is enabled through system programming, parallel connection is not possible. Refer to "1.11.9 Parallelled Telephone" and "2.1.1 Extension Port Configuration" in the Feature Guide for further information.
  • Page 149 3.8.2 Parallel Connection of the Extensions With KX-T7600 Series DPT (except KX-T7665) To DHLC8 card 2-conductor wiring cord 4-conductor wiring cord Connect pins "T" and "R". Connect pins "T", "R", "D1" and "D2". TO MAIN UNIT TO TEL / PABX To DHLC8 card To SLT With Other DPT (except KX-T7560 and KX-T7565)
  • Page 150: Digital Extra Device Port (Digital Xdp) Connection

    3.8.3 Digital EXtra Device Port (Digital XDP) Connection 3.8.3 Digital EXtra Device Port (Digital XDP) Connection A DPT can be connected to another DPT on the Digital XDP connection. In addition, if the DPT is connected to a DHLC8 card, it can also have an SLT connected in Parallel mode or XDP mode. Note •...
  • Page 151 3.8.3 Digital EXtra Device Port (Digital XDP) Connection Using an EXtra Device Port To DLC8/DLC16 card 4-conductor wiring cord To DHLC8 card Connect pins "T", "R", 2-conductor wiring cord (for connection of SLT) "D1" and "D2". Connect pins "T" and "R". 4-conductor wiring cord Connect pins "T", "R", "D1"...
  • Page 152 3.8.3 Digital EXtra Device Port (Digital XDP) Connection With KX-T7600 Series DPT (except KX-T7600E Series) Using a Modular T-Adaptor To DLC8/DLC16 card Modular To DHLC8 card T-Adaptor (for connection of SLT) 2-conductor wiring cord Connect pins "T" and "R". 4-conductor wiring cord Connect pins "D1"...
  • Page 153 3.8.3 Digital EXtra Device Port (Digital XDP) Connection Using an EXtra Device Port To DLC8/DLC16 card 4-conductor wiring cord To DHLC8 card Connect pins "T", "R", 2-conductor wiring cord (for connection of SLT) "D1" and "D2". Connect pins "T" and "R". 4-conductor wiring cord Connect pins "T", "R", "D1"...
  • Page 154 3.8.3 Digital EXtra Device Port (Digital XDP) Connection With KX-T7600E Series DPT Using a Modular T-Adaptor To DLC8/DLC16 card Modular To DHLC8 card T-Adaptor (for connection of SLT) 2-conductor wiring cord Connect pins "T" and "R". 4-conductor wiring cord Connect pins "D1" and "D2". 4-conductor wiring cord Connect pins "D1"...
  • Page 155 3.8.3 Digital EXtra Device Port (Digital XDP) Connection Using an EXtra Device Port Connecting to a Slave DPT To DLC8/DLC16 card To DHLC8 card 4-conductor wiring cord (for connection of SLT) Connect pins "T", "R", 2-conductor wiring cord "D1" and "D2". Connect pins "T"...
  • Page 156 3.8.3 Digital EXtra Device Port (Digital XDP) Connection Connecting to a Master DPT To DLC8/DLC16 card To DHLC8 card 4-conductor wiring cord (for connection of SLT) Connect pins "D1" and "D2". 4-conductor wiring cord Connect pins "T", "R", "D1" and "D2". Master DPT Slave DPT 2-conductor wiring cord...
  • Page 157: First Party Call Control Cti Connection

    3.8.4 First Party Call Control CTI Connection 3.8.4 First Party Call Control CTI Connection CTI connection between a PC and a KX-DT343/KX-DT346/KX-T7633/KX-T7636 DPT provides first party call control. The CTI connection is made via a USB interface (version 2.0), and uses the TAPI 2.1 protocol. A USB Module must be connected to the DPT.
  • Page 158: Connection Of Doorphones, Door Openers, External Sensors, And External Relays

    3.9.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays 3.9 Connection of Doorphones, Door Openers, External Sensors, and External Relays 3.9.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays The PBX supports a maximum of 16 doorphones (KX-T30865/KX-T7765 with a DPH4 card, or German-type doorphone with a DPH2 card), 16 door openers, 16 external sensors, and 16 external relays.
  • Page 159 3.9.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays When loosening/tightening the screw, do not scratch the cabinet wall with the driver shaft. Cabinet Wall Pass the wires through the hole in the base cover, and attach the base cover to a wall using 2 screws. Screw To 8-pin terminal block Note...
  • Page 160 3.9.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays Connection Use 8-pin and 10-pin terminal blocks (included with the card) for connection. While pressing down on the hole at the top of the terminal block using a screwdriver, insert the wire into the side hole as shown below.
  • Page 161: Connection Of Peripherals

    3.10.1 Connection of Peripherals 3.10 Connection of Peripherals 3.10.1 Connection of Peripherals Maximum Distance Cable Maximum Distance ø 0.4 mm: 10 m ø 0.5 mm: 10 m MNT Port ø 0.6 mm: 10 m CAT 5: 10 m Cable Maximum Distance ø...
  • Page 162 3.10.1 Connection of Peripherals BGM/MOH The PBX provides Background Music and Music on Hold. Up to 2 external music sources (e.g., user-supplied radios) can be connected to the PBX. CAUTION • Wiring should be done carefully to prevent undue force being exerted on the plug. Otherwise, sound may only be heard intermittently.
  • Page 163 3.10.1 Connection of Peripherals Connection Charts For connecting a printer/PC with a 9-pin RS-232C connector PBX (9-pin) Printer/PC (9-pin) Circuit Type Signal Signal Circuit Type Pin No. Pin No. (EIA) Name Name (EIA) RD (RXD) RD (RXD) SD (TXD) SD (TXD) ER (DTR) ER (DTR) DR (DSR)
  • Page 164 3.10.1 Connection of Peripherals • Clear To Send (CTS):…(input) An ON condition of circuit CS (CTS) indicates that the printer or the PC is ready to receive data from the unit. The unit does not attempt to transfer data or receive data when circuit CS (CTS) is OFF. •...
  • Page 165: Lan Connection

    3.11.1 LAN Connection 3.11 LAN Connection 3.11.1 LAN Connection Connection Chart for LAN Connection The PBX is equipped with a LAN port for connecting to a LAN so that IP telephones (IP-PTs, IP softphones, SIP Extensions), IP-CSs, PCs and a CTI Server can be connected on a private IP network. IP Softphone LAN Port Switching Hub...
  • Page 166: Power Failure Connections

    3.12.1 Power Failure Connections 3.12 Power Failure Connections 3.12.1 Power Failure Connections When the power supply to the PBX fails, power failure transfer (PFT) will switch from the current connection to the Power Failure Connection. Refer to "2.4.1 Power Failure Transfer" in the Feature Guide for further information.
  • Page 167 3.12.1 Power Failure Connections RJ11 Connector Pin Assignments for Analogue Trunk Card PFT Ports 1 and 2 Signal Name Function Ring port 2 Ring port 1 Tip port 1 Tip port 2 PFT Ports 3 and 4 (for LCOT16 card only) Signal Name Function Ring port 4...
  • Page 168 3.12.1 Power Failure Connections Using BRI Card LINE 1 and LINE 2 of the BRI4 and BRI8 cards can be used for Power Failure Connections. Note When the power returns, the connection will switch back to normal configuration from the Power Failure Connection, and a trunk conversation established during power failure will be dropped.
  • Page 169 3.12.1 Power Failure Connections RJ45 Connector LINE 2 Pin Assignments Signal Name Level [V] Function Reserved – – Receive data 2 Transmit data 1 Transmit data 2 Receive data 1 Reserved – – Installation Manual...
  • Page 170: Starting The Pbx

    3.13.1 Starting the PBX 3.13 Starting the PBX 3.13.1 Starting the PBX Before Starting the PBX Before starting the PBX, please pay attention to the following: Notice The SD Memory Card must be inserted in the SD Memory Card slot of the IPCMPR card before startup. Starting the PBX WARNING Use only the AC power cord included with the PBX for the PSU.
  • Page 171 3.13.1 Starting the PBX Plug the AC power cord into the PBX and an AC outlet, and turn on the PBX. The RUN indicator will flash. Note For safety reasons, do not stretch, bend, or pinch the AC power cord. To AC Outlet While the RUN indicator is flashing, slide the System Initialise Switch back to the "NORMAL"...
  • Page 172 3.13.1 Starting the PBX Installation Manual...
  • Page 173: Guide For The Maintenance Console

    Section 4 Guide for the Maintenance Console Explains the installation procedure, structure, and basic information of the Maintenance Console. Installation Manual...
  • Page 174: Overview

    4.1.1 Overview 4.1 Overview 4.1.1 Overview The Maintenance Console is designed to serve as an overall system programming reference for the PBX. To programme and administer the PBX by PC, you need to install the Maintenance Console onto the PC. This section describes overview and installation of the Maintenance Console only.
  • Page 175: Pc Connection

    4.2.1 PC Connection 4.2 PC Connection 4.2.1 PC Connection Connection via MNT Port of IPCMPR Card MNT Port To LAN Port Notice When connecting a PC to the PBX, a fixed IP address must be assigned to the PC. For information about fixed IP addresses, ask your network administrator.
  • Page 176 4.2.1 PC Connection Make sure that both connector cases (frame ground) of the RS-232C cross cable (shielded cable) are conductive. If they are not conductive, make sure that both connector cases of the cable are firmly connected. If this is not possible, connect the frame of the PBX to the frame of the PC using an earthing wire in order to prevent difference in the electrical potentials.
  • Page 177 4.2.1 PC Connection Note • An AT command (for initialisation, enabling automatic answer, etc.) can only be programmed by Maintenance Console. "AT&F" is stored as the default value. • For more information about the AT command, refer to the external modem’s instructions. Installation Manual...
  • Page 178: Installation Of The Maintenance Console

    4.3.1 Installing and Starting the Maintenance Console 4.3 Installation of the Maintenance Console 4.3.1 Installing and Starting the Maintenance Console System Requirements Required Operating System • Microsoft Windows XP or Windows Vista Business operating system ® ® ® Minimum Hardware Requirements •...
  • Page 179 4.3.1 Installing and Starting the Maintenance Console Quick Setup, you will set up the basic items. For details about the basic items, refer to "2.3.4 Quick Setup" in the Feature Guide. Connect the PC to the PBX with an Ethernet straight cable or RS-232C cross cable. Start the Maintenance Console from the Start menu.
  • Page 180 4.3.1 Installing and Starting the Maintenance Console CAUTION Do not remove the SD Memory Card while power is supplied to the PBX. Doing so may cause the PBX to fail to start when you try to restart the system. Installation Manual...
  • Page 181: Troubleshooting

    Section 5 Troubleshooting This section provides information on the PBX and telephone troubleshooting. Installation Manual...
  • Page 182: Troubleshooting

    5.1.1 Installation 5.1 Troubleshooting 5.1.1 Installation PROBLEM PROBABLE CAUSE SOLUTION You cannot make/receive • • IP-EXT/IP-GW/DSP Replace the corresponding card. calls via an IP network. card malfunction • • IPCMPR card Replace the IPCMPR card (be sure to turn malfunction off the PBX when replacing).
  • Page 183 5.1.1 Installation PROBLEM PROBABLE CAUSE SOLUTION Extensions (except IP-PT/ • • Extension card Replace the corresponding card. SIP Extension) do not malfunction operate. • • Poor connection Take the extension and plug it into the between the PBX and same extension port using a short the extension telephone cord.
  • Page 184 5.1.1 Installation PROBLEM PROBABLE CAUSE SOLUTION The LINK indicator of the • • IP-EXT/IP-GW card Replace the corresponding card. IP-EXT/IP-GW/IPCMPR malfunction does not turn on. • • IPCMPR card Replace the IPCMPR card (be sure to turn malfunction off the PBX when replacing). •...
  • Page 185: Connection

    5.1.2 Connection 5.1.2 Connection Connection between the PBX and a PT: CAUSE SOLUTION Can you dial The T/R is connected to the D1/D2. Use the correct cord (the an extension? inner 2 wires are for T/R and the outer 2 wires are for D1/D2) Extension Connection between the PBX and an SLT:...
  • Page 186 5.1.2 Connection Connection between the trunk and the PBX: CAUSE SOLUTION (Continued from the Trunk is connected to the T2/T1. Reconnect the trunk to previous page.) the T1/R1 or T2/R2 of the telephone jack using 2- conductor wiring. Can you dial out on a Trunk trunk?
  • Page 187: Operation

    5.1.3 Operation 5.1.3 Operation PROBLEM PROBABLE CAUSE SOLUTION • • • Cannot set the IP An unusable value is Set an IP address within the valid range. address, subnet mask being set. IP address of the IP-PT/PBX: "1.0.0.0" to address, and PBX IP "223.255.255.255"...
  • Page 188 5.1.3 Operation PROBLEM PROBABLE CAUSE SOLUTION • • • Originating an outside The corresponding Programme the flexible button. Refer to call, call transfer, or flexible button does not "1.20.2 Flexible Buttons" in the Feature conference cannot be exist on the PT. Guide.
  • Page 189: Using The Reset Button

    5.1.4 Using the Reset Button 5.1.4 Using the Reset Button If the PBX does not operate properly, use the Reset Button. Before using the Reset Button, try the system feature again to confirm whether there definitely is a problem or not. CAUTION In order to avoid possible corruption of data on the SD Memory Card, please ensure that the "SD ACCESS"...
  • Page 190: Troubleshooting By Error Log

    5.1.5 Troubleshooting by Error Log 5.1.5 Troubleshooting by Error Log When a major system error occurs in the PBX, the ALARM indicator on the front of the shelf turns on red, and the system logs the error information. Error Log Display Format Below is the display format of the error log.
  • Page 191 KX-TDE100 (Physical slot): 00 to 06 (00: IPCMPR Card Slot/Built-in ESVM card; 01 to 06: Free Slots) – KX-TDE200 (Physical slot): 00 to 11 (00: IPCMPR Card Slot/Built-in ESVM card; 01 to 11: Free Slots) – KX-TDE100/KX-TDE200 (Virtual slot): 01 to 08...
  • Page 192 5.1.5 Troubleshooting by Error Log Installation Manual...
  • Page 193: Appendix

    Section 6 Appendix Installation Manual...
  • Page 194: Revision History

    6.1.1 PMMPR Software File Version 2.0xxx 6.1 Revision History 6.1.1 PMMPR Software File Version 2.0xxx New Options • System Components Table • 16-Port Single Line Telephone Extension Card with Caller ID (CSLC16) KX-TDA0177 • 2-Channel Simplified Voice Message Card (ESVM2) KX-TDA0192 •...
  • Page 195: Pmmpr Software File Version 2.01Xx

    6.1.2 PMMPR Software File Version 2.01xx 6.1.2 PMMPR Software File Version 2.01xx New Options • System Components Table • 1-Channel IP Proprietary Telephone Activation Key (1 IP PT) KX-NCS4501 • 1-Channel SIP Extension Activation Key (1 SIP Extension) KX-NCS4701 • 1-Channel IP Softphone/IP Proprietary Telephone Activation Key (1 IP KX-NCS4201 Softphone/IP PT)
  • Page 196: Pmmpr Software File Version 3.0Xxx

    6.1.3 PMMPR Software File Version 3.0xxx 6.1.3 PMMPR Software File Version 3.0xxx New Options • System Components Table – Activation Key for CA Basic for 1 User (CA Basic 1user) KX-NCS2101 – Activation Key for CA Basic for 5 Users (CA Basic 5users) KX-NCS2105 –...
  • Page 197: Index

    Index Installation Manual...
  • Page 198 Index 8-Port E & M Trunk Card (KX-TDA0184) 26, 96 Numerics 8-Port Single Line Telephone Extension Card 16-Channel Echo Canceller Card (KX-TDA0166) 25, 142 (KX-TDA0173) 26, 126 16-Channel IP Proprietary Telephone Activation Key (KX-NCS4516) 16-Channel IP Softphone/IP Proprietary Telephone Activation Key (KX-NCS4216) About the software version of your PBX 16-Channel SIP Extension Activation Key...
  • Page 199 KX-NCS4716 (16-Channel SIP Extension Activation Ferrite Core Key) First Party Call Control CTI Connection KX-NCS4950 (Activation Key for Software Upgrade to Floor Standing (KX-TDE200 Only) Enhanced Version) Frame Earth Connection KX-TDA0103 (L-Type Power Supply Unit) 25, 54 Front Cover, Closing...
  • Page 200 26, 90 KX-TDA0184 (8-Port E & M Trunk Card) 26, 96 Pager KX-TDA0187 (T-1 Trunk Card) 26, 98 Panasonic Proprietary Telephones, Compatible KX-TDA0188 (E-1 Trunk Card) 26, 101 Panasonic Proprietary Telephones, Incompatible KX-TDA0189 (8-Port Caller ID/Pay Tone Card) 26, 94...
  • Page 201 Virtual 32-Channel SIP Extension Card (V-SIPEXT32) Virtual 32-Channel VoIP Extension Card (V-IPEXT32) Virtual 4 IP Cell Station Interface Card (V-IPCS4) Virtual Cards Virtual Extension Slot Virtual Trunk Slot V-SIPEXT32 (Virtual 32-Channel SIP Extension Card) Wall Mounting (KX-TDE100) Wall Mounting (KX-TDE200) Wiring Precautions Installation Manual...
  • Page 202 Panasonic Communications Co., Ltd./Panasonic Communications Company (U.K.) Ltd. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting: http://www.doc.panasonic.de...
  • Page 203 Notes Installation Manual...
  • Page 204 Copyright: This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., Ltd. Panasonic Communications Co., Ltd. 2009...

This manual is also suitable for:

Kx-tde100

Table of Contents